Aube Technologies TH102 Owner's Manual

400-102-000-A 1/4

MODELS TH102 & TH102-3

SUMMARY

OPTIONS SELECTION

To change the temperature from °C to °F and back, maintain DAY

buton pressed down as RESET button is being pressed on and

released. Then release DAY button.

To change the time format from 24 hrs. to 12 hrs. and back, maintain

HOUR button pressed down as RESET button is being pressed on

and released. Then release HOUR button.

To change the heating control from proportional to on/off and back,

maintain MIN button pressed down as RESET button is being

pressed on and released. Then release MIN button.

TO SET TIME AND DAY

Press on DAY, HOUR and MIN buttons to adjust time and day.

TO RECORD THE HEATING PROGRAMS

Set the operating mode to AUTO. Use the PGM button to select the

program to be recorded or modified. Once the program is selected,

use HOUR and MIN buttons to set time and    or    to select

temperature setting.

TO RECORD THE ECONO PROGRAMS

Set the operating mode to ECONO. Use the PGM button to select the

program to be recorded or modified. Once the program is selected,

use DAY, HOUR and MIN buttons to set time and      or      to select

temperature setting.

OPERATING MODES

To select an operating mode, use MODE button.

AUTO:

Runs the program.       or      shows temperature setting

and can override temporarily your programming.

MAN:

Maintain the selected temperature.       or      change

the temperature setting.

ECONO:

Maintain a temperature setting up to the user's pre-

programmed day and time.       or      shows temperature

setting and can override temporarily your programming.

INSTALLATION

Note:

The "Problems and Solutions" section at the end of this user's guide

will help you to correct your problems during the installation.

This thermostat has been designed to operate with any installation which has a

RESISTIVE load not exceeding 2500 W @ 240 VAC or 1250 W @ 120 VAC such

as electric baseboards, radiant ceilings and floors, electric convectors, etc. It is

not compatible with a low voltage controller used by a central heating system or

systems using a contactor or a relay whose current is under 1.0 A.

Electricians or experienced technicians should install the thermostat.

This thermostat is designed to be used with a self-protected heating system

equipped with thermal cut off and circuit breaker.

PARTS INCLUDED

- One (1)  thermostat

- Two (2) 6-32 screws, 1 ½  inches

- Two (2) solderless connectors

TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER

PANEL TO AVOID ELECTRICAL SHOCK.

Keep air vents of thermostat clean

and free from obstructions.

1) Connecting wires and mounting thermostat

Connect the rear thermostat wires to the power supply and to the electric heater

wires using solderless connectors for copper wires 

(there is no polarity for the

wires)

. See schematic diagram.

2-wire installation :

Electric baseboard

120 / 240 VAC

Line

Solderless

connector for

copper wires

NOTE: 

To access the programmable keyboard, remove the cover by placing

your fingers to the right side of the thermostat and pull toward you.

Push the excess wire back into the electrical box to prevent interference with the

thermostat. Secure the thermostat using the supplied screw. Once the thermostat

is properly installed, return power to heating system.

Note 1 :

All cables and connections must conform to the local electrical

code.

Note 2 :

In normal use at full capacity (2500 W), the housing temperature of

the thermostat can reach 35 to 40 °C.

WARNING :

Special CO/ALR solderless connectors must be used when

connecting with aluminum conductors.

2) Options selection

Some options have been factory set. Those default settings are :

• The temperature is in °C, the heating control is proportional and the time

format is 24 hrs.

2.1 Temperature displayed in °C or °F 

To change the temperature from °C to °F and back, maintain  DAY button pressed

down as RESET button is being pressed on and released. Then release DAY but-

ton.

2.2 Time format displayed in 24 hours or 12 hours

To change the time format from 24 hrs. to 12 hrs. and back, maintain HOUR but-

ton pressed down as RESET button is being pressed on and released. Then

release HOUR button.

4-wire installation :

Electric baseboard

120 / 240 VAC

Line

Solderless

connector for

copper wires