Aube Technologies TH132 A Owner's Manual

Thank you for choosing the Aube TH132, a programma-

ble thermostat that provides both energy savings and total

comfort.

n

DAY/HOUR/MIN—Set the day and clock settings.

o

PGM—Program the schedule (programs).

p

MODE—Select the operating mode.

RETURN—To exit a function.

q

To configure temperature setpoints:

 Comfort

, 

  Economy and 

 Vacation.

r

Adjust the floor temperature limit (AF only).

s

—Increase and decrease temperature.

t

—Indicates the number of the current 

program when Automatic mode is enabled.

u

Current operating mode (auto

/ 

manual ). 

In 

Auto mode, the program’s associated setpoint icon is 

also displayed (

).

v

Indicates the room OR floor temperature.

w

Heating indicators (see “Temperature Control” 

below).

TH132-A

This model has been designed to control a room’s ambi-

ent temperature.

The TH132-A has one temperature sensor located in the

control module.

TH132-AF

This model is designed to use a floor sensor to control the

room temperature. 

The TH132-AF has two temperature sensors:

•

The first one, installed in the control module, controls

the ambient temperature. 

•

The second one, installed in the floor (and connected

to the power base), limits the temperature of the floor

(the default setting of this limit is 82°F). 

TH132-F

This model is designed to control floor heating systems. 

The TH132-F has one temperature sensor installed in the

floor (sensor is connected to the power base).

The TH132 has two switches, located on the upper-left

part on the rear of the control module, which are used to

set the following options:

Early Start

When the Early Start function is enabled (disabled by

default), the TH132 calculates the optimum system start

time to obtain the desired temperature by the set time. To

enable this function:

Position switch #1 down.

Note:

When this function is enabled, the

system can be activated before the pro-

gram’s start time. 

Temperature Display

By default, the TH132 displays the temperature in °C. If

you wish to change to °F:

Position switch #2 up.

Note:

When you switch from °C to °F or vice

versa, the  ,   and   setpoints must be

redefined.

Control Module

TH132 A/F/AF

Owner’s Guide

TH132 Description

Models Overview

Configure the Switches

Align the bracket tabs on the control module with the

holes located on top of the power base.

This control module must be installed on a PB130 series

power base.

Note:

Keep the thermostat's air vents clean and free from

obstructions.

Note:

The screw cannot be removed completely.

On the first installation, the screen displays: 

0:00, MO,  and temperature (room/floor). 

For Floor Heating Installations: 

One of the two following messages may be dis-

played when a problem occurs:

LO

: The floor temperature is below 32°F (0°C), or 

the temperature sensor is defective, or not 

connected. 

The heating indicator 

 is displayed and 

the relay is closed (energized).

HI

: The floor temperature is above 

140°F (60°C), or the temperature sensor is 

defective.

n

Set the time (HOUR - MIN).

o

Set the day (DAY).

If you remove the module from its base for more than

2 hours, the time and day will have to be reprogrammed.

Comfort 

and Economy 

Setpoints

These setpoints are associated with the schedule’s pro-

grams (prog. 1 & 3 = Comfort, prog. 2 & 4 = Economy)

and are preprogrammed as follows:

A & AF models—

 68°F,   64°F

F model—

 82°F,   68°F

To modify a setpoint:

n

Set the temperature using 

 and press and hold the 

 or 

 button until it is displayed on the screen.

o

Press MODE/RETURN to exit.

Vacation Setpoint 

The vacation setpoint is associated to the Vacation oper-

ating mode and is preprogrammed to 50°F. To modify this

setpoint, repeat above steps.

Floor Temperature Setpoint (AF model only)

The floor temperature limit is preprogrammed to 82°F to

avoid damage to your floor. 

To modify, press the adjustment button (below ) using a

pointed object, set the desired temperature using 

 and

press MODE/RETURN to exit.

The TH132 offers three operating modes:

Automatic —

Executes the schedule.

n

Press MODE to select 

. The current 

program number is displayed.

You can temporarily bypass the current

program by setting a specific temperature setpoint

 or by selecting one of the pre-defined setpoint

buttons (

). The new setpoint will be maintained

until the beginning of the next program.

Manual 

—Maintains a constant temperature.

n

Press MODE to select   .

o

Set temperature 

 or select one of the pre-

defined setpoint buttons (

).

Vacation

—Maintains the Vacation setpoint 

during a prolonged absence. 

Press .

Install the Control Module

Power base

Control module

Air vents

Air vents

First Power ON

Set the Time and Day

Adjust the Temperature Setpoints 

Select the Operating Mode

400-132-000-A