Auber WSD-1501GPH Quick Manual

Other manuals for WSD-1501GPH: Operation & Instruction Manual

Page of 14

Download

Print this page

Bookmark us

No part of this manual shall be copied, reproduced, or transmitted in any way without the prior, written consent of Auber Instruments.

Auber Instruments retains the exclusive rights to all information included in this document.

Quick Guide for WSD-1501GPH

Programmable PID Temperature Controller with Dual Probe

Version 1.0 (September, 2016)

Auber Instruments

5755 North Point Parkway, Suite 99

Alpharetta, GA 30022

770-569-8420

www.auberins.com

Introduction

Thank you for purchasing the Auber WS series temperature controller. We sincerely

appreciate your decision and trust that our machine will meet your expectations in both

the quality of the result and the value of our product. While we are delighted that you may

be anxious to operate the controller for your project, a few minutes of your time reading

through this manual will only serve to enhance your experience in the months and years

ahead. In particular, we urge you to read through the safety warnings below. Although

this plug-and-play controller is very easy to operate, the process involves high

temperature and high wattage appliances and your safety is paramount.

SAFETY WARNINGS

This controller is designed only to be used with devices that have limited power

and their own thermal cut off protection, such as a thermostat or thermal fuse in

case of controller failure.

Do not place any objects on the top of controller surface which is used to vent

excess heat during its operation.

The maximum electric current this controller can handle is 15 ampere. For 120

volt AC in US and Canada, this limits the heater power to 1800 watts.

Always place the sensor in the controlled subject when the controller is on. Before

turning on the controller, please make sure the sensor is placed inside the

container to be controlled. Leaving the sensor outside of the solution will form an

open loop operation. If the sensor is left outside, controller will assume the

temperature is low even if the controlled subject is already very hot. The controller

will provide full power to the heater. It will not only overheat the controller, but also

damage your appliance, and even cause a fire.

This controller is designed to control the devices recommended by Auber

Patent pending

1 2 3 4 5 6 7 Next › »

Summary of WSD-1501GPH

Page 1
Copyright 2007-2016, auber instruments inc. All rights reserved. No part of this manual shall be copied, reproduced, or transmitted in any way without the prior, written consent of auber instruments. Auber instruments retains the exclusive rights to all information included in this document. Quick g...
Page 2
2 instruments only. Using it to control a not recommended device can be dangerous and cause fire. Auber instruments is not liable for damages caused by misuse of the controller. If you are not sure the controller can be used, please contact auber instruments before use. If an abnormal display or noi...
Page 3
3 4) smoker generator control output status indicator . When lit, the smoker generator control output is on. When off, the output is off. 5) timer status indicator - when lit, right window shows the time passed since power up. When it is off, right window shows the current temperature detected by th...
Page 4
4 cabinet temperature. We name it probe 1. It needs to be plugged to the top sensor jack at the back of the controller. The long probe with a bend at the end is for the meat internal temperature measurement. It needs to be plugged to the bottom sensor jack at the back of the controller. The tips of ...
Page 5
5 cable b: power cable for smoke generator, nema5-15p plug 1) connection for bradley original smoker, with control of the smoker generator. A) connecting the controller to the power outlet, you should use the power cord that came with the bradley smoker for connecting the smoker generator to the pow...
Page 6: Smoke
6 c) connecting the controller output to the bradley smoker tower with the power cord that came with the auber controller auber controller smoke generator smoker tower probe 1: cabinet temp probe 2: internal temp cable a cable b to power outlet figure 5. Diagram figure 6. Back view.
Page 7: Smoke
7 figure 7. Connection between the controller and smoker 2) connection for bradley digital smoker. For the bradley digital smoker, both controller and smoker generator should be connected directly to the wall outlet. Connect the controller output with the smoker tower. Auber controller smoke generat...
Page 8
8 3. Programming the smoking temperature profile. A total of 6 steps can be programmed for this controller. Each step contains the set temperature (c-x) and an ending criteria setting (e-x), where “x” is the step number (e.G. Step 4 temperature is represented by c-4 and step 4 ending criterion is re...
Page 9
9 hours, waiting you to pick the food. If you set c-3=0 and t-3=0, when meat internal temperature reaches 160 °f, the controller will shut off the heater, flashing end on both windows, and turn on the beeping alarm to notify you that cooking is finished. Table 1. Initial program setting step # temp ...
Page 10
10 6. Important consideration for better control results. The following is a list of things that could affect the result of temperature control. A) the smoker and controller location. The smoker should not be placed directly in the sun. Direct sun light can heat the smoker to above 140 °f in the sum...
Page 11
11 7. Program the smoker generator on step. The smoker generator is controlled by the parameter r1 and r2. These two parameters determine which steps to turn on the smoker generator. The smoker generator will stay on only for the step it is programmed. It will turns off when program goes to the next...
Page 12
12 be higher than the alarm temperature. D) ast is the step ending alarm. When ast is turned on, the buzzer will beep 4 times when each step is finished. It is useful to notify the user the cooking step is finished. User can turn it off if no buzzer sound is wanted at the finish of each step. Note :...
Page 13
13 10. Single-step mode in this mode, the controller will hold temperature at one set value (c-1) continuously as long as the controller is powered on. Even if the controller is powered off and turned on again, it will resume working in this mode. You do not need to enter any other program steps in ...
Page 14
14 normal operating mode and will start run the current program. C. Store your program as recipe (single-step mode) before you input your set temperature, check the prg = off (accessed by lck code “3”). Press set key once, and then set c-1=150, press set again to confirm and exit. The controller wil...