Audible Rush Jam-Pac Premium Plus User Manual - page 2
BRACKET INSTALL
OPERATION
1. Open player cover. With the Jam-Pac amp turned
off, plug the audio cable into the headphone jack of
player and Install player under hinged cover per
‘PLAYER INSTALL’ instructions. Dress excess audio
cable into space under player deck.
2. Set player volume high on player, around 90% to
95% level.
3. Close player cover and secure latch.
4. Recharge player BEFORE EACH USE using the supplied
Lithium Ion charger by inserting the charger cable into
the side opening shown.
ONLY USE AUDIBLE RUSH SUP-
PLIED CHARGERS
as safety circuits are included to pre-
vent battery overload and possible property damage
from overcharged Lithium Ion cells. When connected to
the Jam-Pac, the charger lights red while active and
turns green when battery is full. It will take 2-4 hours
to reach full charge.
5. Slide Jam-Pac into mount and unzip cover. Fold cover
as shown and secure in place with bag side buckles.
Buckles can be adjusted to hold the cover tight against
bag front.
6. Press the on/off button momentarily. LED lights green
indicating amp is on. If no music plays for about 30 minutes, the unit will shut
off to save battery power.
7. Use Jam-Pac thumbwheel to set desired volume level.
8. In the event of rain, pull over, zip cover closed and continue listening.
USB PLAYER CHARGER OPERATION
a. Using a toothpick or paper clip, slide the USB
CHARGER MODE SWITCH according to your
player: A= Apple products, B=all others. Posi-
tion C is reserved for future use.
b. Attach USB cable (supplied with your
smartphone charger) to Jam-Pac USB power port. Dress cable between into
lower storage compartment. Bring cable back up from compartment and plug
into phone’s charger port, leaving excess cable in lower compartment.
c.
With Jam-Pac off, and USB charger connected to player, hold on/off button for
about 10 seconds or until your player indicates it is receiving a charge.
The
USB charger will automatically shut down after about 30 minutes. To restart the
charger, simply power Jam-Pac off and again, hold on/off button for 10 seconds.
This can be repeated as desired.
Buckles (
2)
Use plastic spac-
er rings plus 3”
rubber strips
Use plastic
spacer
rings only
Do not
use any
spacers
1) Determine which spacers
to use: Temporarily snap
plastic spacer ring over bar
and pinch closed with fin-
gers. If it looks like the
picture, then...
3) Insert 4 screws.
Place mount in verti-
cal position and
tighten so that
bracket does not
rotate on handlebar
.
4) Adjust one end of
cable so it is flush
and tighten set
screw. Pull other end
of cable tight
(remove all slack)
and tighten set
screw. Trim excess cable.
Cable
Stem
Spacers
Clamps
2) Place spacers (if any) around each side of handlebar. Wrap cable under stem, feeding
ends into far 2 holes in bracket. Place 2 clamps over spacers and slide bracket over clamps.
Brack
et
5) Clip on.
PLAYER INSTALL
Jam-Pac comes set for iPhone- Insert audio cable in player audio jack.
Set player volume to 90%. Close and secure player cover latches.
For MP3 players such as iPods- Remove bottom thin player insert.
Replace with thick player insert, followed by medium player insert
with cutouts. This raises player so controls will operate through the
clear film. Insert audio cable in player audio jack, routing cable BE-
TWEEN layers of insert. Store excess cable under base.
For other players– 1. Connect audio cable: Route cable either up or
down inside channel. Store excess cable under base. 2. Snug Player: Remove back-
ing from self adhesive Install Strips and place on sides, top and bottom of player
base walls creating a snug fit for player. Use multiple layers of Install Strips as nec-
essary. 3. Set Player Height- Player must be positioned against underside of player
cover window when cover is closed in latched position. This allows player controls
and touch screen to operate through the clear film. Place 1 or 2 sets of Install Strips
on floor to raise player. Stack several Install Strips as necessary.
IMPORTANT: Set player volume to 90%
Latch
H
in
ge
Charg
e
Volum
e
On/
Off
Power On LED