Summary of ASP2802
Page 1
Quick start guide version: 1.00
Page 2
Page -2- © audient ltd asp2802 installation................................................... Page 3 warning 3 safety & mains (fuse information) 4 dimensions & specification 5 ventilation 6 optional rack ear installation 7 channel strip controls................................................ Page ...
Page 3
Page -3- © audient ltd installation.
Page 4
Page -4- © audient ltd installation package contents your asp2802 console has been carefully and meticulously tested and inspected before dispatch. Please check for any signs of transit damage. If any signs of mishandling are found please notify the carrier and inform your dealer immediately. Your 2...
Page 5
Page -5- © audient ltd installation asp2802 dimensions (including rubber feet) height front - 60 mm height rear - 170 mm width - 450 mm depth - 550 mm height (depth) when racked 13ru plus connector space - 15ru asp2802 specifications some general performance figures from the console - taken with pri...
Page 6
Page -6- © audient ltd installation ventilation care should be taken not to obstruct the series of ventilation holes in the metalwork of the console. The desk is designed to release heat and take adequate air flow via these holes to ensure longevity of performance. These can be found along the left ...
Page 7
Page -7- © audient ltd rack installation (optional) please note that rack ears for asp2802 are an optional extra..
Page 8
Page -8- © audient ltd channel strip.
Page 9
Page -9- © audient ltd master section.
Page 10
Page -10- © audient ltd control surface panel control surface installation please refer to the separate daw specific control surface manuals found online at www.Audient.Com to guide you through installation, setup and configuration of asp2802 as a daw control surface..
Page 11
Page -11- © audient ltd rear panel channel connections.
Page 12
Page -12- © audient ltd db25 wiring specification the following table provides channel counts for each db25 connector: summing input daw inputs direct outputs input 1l (24, 12, 25) daw input 1 (24, 12, 25) dir out 1 (24, 12, 25) input 2r (10, 23, 11) daw input 2 (10, 23, 11) dir out 2 (10, 23, 11) i...
Page 13
Page -13- © audient ltd rear panel master connections.
Page 14
Page -14- © audient ltd daw ethernet connection (mac) you can use standard cat-5e ethernet cable to connect asp2802 to your studio daw computer. The interface in asp2802 is compatible whether you use a straight through or cross-over cable. Please ensure that you have downloaded and installed the lat...
Page 15
Page -15- © audient ltd networking (mac) once you have connected asp2802 to your studio computer via either a direct ethernet link or through a router and installed aunet you are ready to set up the networking side of the console. Ip address setup for direct connection unless you have a router in yo...
Page 16
Page -16- © audient ltd networking (mac) moving across to asp2802, power up the console and once booted, press the setup button. The oled displays will show the first page of console setup. First set the application you are using with asp2802. The options at the time of release include: • apple logi...
Page 17
Page -17- © audient ltd networking (mac) subnet mask set to 255.255.255.0: port set to 1212: press the setup key to exit setup and your setting will be saved. Now power down the console and restart your apple computer. Once booted, ensure that the aunet application is running and open on your daw ma...
Page 18
Page -18- © audient ltd networking (mac) your console should now be connected to your studio daw computer and ready for configuration as a hui tm control surface and analogue automation platform. Setting up the console with dhcp (for use with routers) if you have more than one device connected to yo...
Page 19
Page -19- © audient ltd daw ethernet connection (pc) you can use standard cat-5e ethernet cable to connect asp2802 to your studio daw computer. The interface in asp2802 is compatible whether you use a straight through or cross-over cable. Please ensure that you have downloaded and installed the late...
Page 20
Page -20- © audient ltd networking (pc) once you have connected asp2802 to your studio computer via either a direct ethernet link or through a router and installed aunet you are ready to set up the networking side of the console. Until your console is connected (or any other lan device to your pc), ...
Page 21
Page -21- © audient ltd networking (pc) in the local area connections properties dialogue window scroll down and select internet protocol tcp/ip and then open the properties dialogue box with the button to the right. Here select the ‘ use the following ip address ’ radio button. Set the ip address o...
Page 22
Page -22- © audient ltd networking (pc) moving across to asp2802, press the setup button. The oled displays will show the first page of console setup. First set the application you are using with asp2802. The options for pc at the time of release include: • avid pro tools 8 • steinberg cubase 5 (nue...
Page 23
Page -23- © audient ltd networking (pc) subnet mask set to 255.255.255.0: port set to 1212: press the setup key to exit setup and your setting will be saved. Now power down the console and restart your pc. Once booted, ensure that the aunet application is running and open on your daw machine. Finall...
Page 24
Page -24- © audient ltd networking (pc) your console should now be connected to your studio daw computer and ready for configuration as a hui tm control surface and analogue automation platform. If you need to exit the aunet program it will still run in the systray until you manually quit by right c...
Page 25
Page -25- © audient ltd networking (pc) you will most likely be running dhcp with automatic ip hand out. Ensure that the console is set to use dhcp on the second page of the setup menu, once set reboot the console and follow the same aunet connection procedure as outlined previously once the console...
Page 26
Page -26- © audient ltd example systems example system 1 - 8 channel daw platform the first example system shown on the next page illustrates a basic system with a typical 8-in and 8-out soundcard / interface as commonly available. In this example there are 8 microphone channels, some basic outboard...
Page 27
Page -27- © audient ltd example systems example system 3 cont. If you wish to work it another way, an all analogue, zero-latency monitor mix could be formed by feeding the analogue output of asp008 (or whatever standalone preamplifiers you are using) into the db25 daw input connection. Using the alt...
Page 28
Page -28- © audient ltd example system 1.
Page 29
Page -29- © audient ltd example system 2.
Page 30
Page -30- © audient ltd example system 3.
Page 31
Page -31- © audient ltd example system 4.
Page 32
Page -32- © audient ltd bus compressor settings.
Page 33
Www.Audient.Com audient ltd 1 stable court herriard park herriard hampshire rg25 2pl uk phone: +44 (0) 1256 381944 fax: +44 (0) 1256 381906.