Audinate Dante-MY16-AUD2 Getting Started Manual - Dante-My16-Aud2 Overview
Dante-MY16-AUD2 Getting Started Guide
- 4 -
Dante-MY16-AUD2 Overview
Sample-accurate timing with inaudibly low latency.
Dante uses audio-independent, high- accuracy network
synchronization standards to ensure all Dante devices are synchronized at all times. Sample-accurate playback
with extremely low latency and jitter is achieved without limiting your audio sample rates and network layout
options.
True Ethernet and IP network compatibility.
Dante networking runs over inexpensive off-the-shelf computer
networking hardware, and does not require dedicated network infrastructure. Ethernet switches transmit Dante
digital media streams alongside ordinary data traffic, so you can integrate professional media operations into
properly designed pre-existing networks.
Easy to set up and use.
Our innovative configuration protocols make networking a true plug-and-play process
with automatic device discovery and system configuration. Simply connect your Dante-MY16-AUD2 to a network
and it will automatically configure its network interface before finding and being found by other Dante-enabled
devices on the network. Instead of “magic numbers”, you label Dante network devices and their audio channels
with names that make sense to you.
Using Dante Controller (a free application for PC or Mac), you can instantly see all Dante-enabled devices on
the network, edit channel and device labels as you like, and route audio with a single click. With Dante Virtual
Soundcard, your computer looks and acts like any other Dante-enabled device on the network. Just connect your
computer to a network switch to use digital audio processing, recording or playback software on the network. You
can also use Dante Via
™
to ‘Dante-enable’ all audio applications and devices installed on or connected to your
computer, and to route audio to and from a Dante network. See www.audinate.com for more information.
The Dante-MY16-AUD2 card can be configured to handle 16 input channels and 16 output channels at 44.1kHz
or 48kHz, or 8 input channels and 8 output channels at 88.2kHz or 96kHz, of 16, 24 or 32-bit uncompressed
digital audio data using Audinate’s Dante audio networking standard.
Specification Summary
Sample rates
44.1kHz, 48kHz, 88.2kHz and 96kHz
Sample rate pull-up/down
+4.1667, +0.1, -0.1, and - 4.0 %
Audio channels
16x16 @ 44.1kHz and 48kHz OR 8x8 @ 88.2kHz and 96kHz
Sample bit-depth
16, 24 or 32-bit PCM
Audio transport formats
Dante Audio over IP, AES67 RTP
Network
2 x Gigabit (1000Mbps) Ethernet RJ45 connectors
Redundancy
Glitch-free Dante audio redundancy using dual Ethernet networks (redundant mode)
Daisy chaining
Daisy chain multiple Dante-MY16-AUD2 cards together (switched mode)
HA Remote
Support for HA Remote capable Yamaha products
Expandable
Install up to four Dante-MY16-AUD2 cards in available MY16-compatible slots for up to 64x64 audio channels
Compatible Yamaha
equipment:
Compatible with a range of digital mixing consoles, processors and power amps equipped with MY16-interface
compatible card slots, including:
Digital Mixers
CS-R10, DSP-R10, RPio622, CL5/3/1, QL5/1, PM5D, DSP5D, M7CL, LS9, DM2000, DM1000, 02R96, 01V96, 01V96i
Interfaces
RSio64-D
Processors
MRX7-D, MTX5-D, DME24N, DME64N
Power Amps
Tx4n, Tx5n, Tx6n
Synchronization
High quality on-board VCXO clock can provide master clock OR slave from audio equipment; automatic
synchronization with Dante network
About Dante Networking (cont’d)