1. DL manuals
  2. Audio Design Associates
  3. Music Equipment
  4. Suite 16
  5. System Design & Technical Documentation

Audio Design Associates Suite 16 System Design & Technical Documentation

Manual is about: Multi-room

Summary of Suite 16

  • Page 1

    System design & technical documentation 602-610 mamaroneck avenue, white plains, ny, 10605, www.Ada-usa.Com, 1-800-hd-audio, fax (914) 946-9620 r evised a pril ‘02.

  • Page 2: Contents

    - 1 - all specifications subject to change without prior notice. ©2002 audio design associates, inc. All rights reserved. Contents suite 16 modules ........................................................................ 2 a-16 audio input module ........................................................

  • Page 3: Suite 16 Modules

    - 2 - suite 16 modules suite 16 is appropriately named as it is a system that is built using a suite of modules and components. These modules and other components allow extraordinary flexibility in the de- sign of a distributed entertainment system. This section will focus on the three modules that ...

  • Page 4: A-16 Audio Input Module

    - 3 - a-16 audio input module only one a-16 audio input module is used per suite 16 system. Audio inputs the a-16 features 16 stereo rca jacks which are the sixteen audio inputs to the system. Input level trim control by and large most audio source components put out audio signal levels that are clo...

  • Page 5: Irl-5000

    - 4 - the two low voltage triggers can also be used to en- gage an “on” and an “off” ir command when using ada’s irl-5000 to control source components. The irl-5000 is an advanced version of ada’s irl- 3000 infrared learner and uses the same pc soft- ware program to capture, test, layout, and label ...

  • Page 6

    - 5 - 1 2 3 4 5 6 7 8 to 9 pin "d" delta-88 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1000 watts max total set shunting pins to engage ac with zone or source numbers 1-8 120-240 vac 50-60 hz quad ac controller acc-48 caution risk of electric shock do not open attention! Risque de choc electriq...

  • Page 7: Sources 1-8

    - 6 - 1/2 asb 115v~ 1/4 asb 230v~ 115v~/60hz • 230v~/50hz 500 watts max caution risk of electric shock do not open attention! Risque de choc electrique. Ne pas ouvrir made in u.S.A. 230v 115v 1 gnd 2 fdbk 3 cntrl 4 +v ada bus® network control i/o main ac input switch ac (10a) warning! Risk of hazard...

  • Page 8: Acc-48

    - 7 - 1 2 3 4 5 6 7 8 to 9 pin "d" delta-88 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1000 watts max total set shunting pins to engage ac with zone or source numbers 1-8 120-240 vac 50-60 hz quad ac controller acc-48 caution risk of electric shock do not open attention! Risque de choc electriq...

  • Page 9: Paging Features

    - 8 - party functions there are four “party” functions which when activated, cause rooms to switch to the selected source. As room outputs are programmed to track party groups, this feature is discussed under p-16 features. Paging features the a-16 also features a seventeenth input for paging. Unlik...

  • Page 10: P-16 Preamplifier Module

    - 9 - the second trigger is a low voltage input trigger (3-24v ac or dc). It connects to the a-16 on the removable 5-pin screw terminal connector on the far right side of the a-16 module (pin 4 is [+] and pin 5 is [-], polarity does not matter for an ac trigger). The low voltage trigger, once activa...

  • Page 11

    - 10 - volume and tone presets each zone has four volume and four tone presets. Each of these eight presets has a serial command to store the settings and another to recall these settings. The tone presets recall and store both a bass and treble level as well as loudness and stereo enhancement filte...

  • Page 12

    - 11 - playing different sources at the same time. As such, the installer can program the controls in these rooms to send party input commands instead of the standard input commands. As such, whenever someone selects cd in the living room, the dining room and entry foyer will turn on to cd as well. ...

  • Page 13: Power Amplifier Options

    - 12 - low voltage triggers the p-16 features three low voltage trigger outputs: two 9-pin “d” type connectors (these are not rs-232) and one removable five-pin screw terminal connector. The top 9-pin “d” connector provides a single ground pin and six pins that go to +12vdc individually with respect...

  • Page 14

    - 13 - individual zones bypass trigger all zones 12vdc 1(-) 2(+) voltage selector 4 asb - 115v~ 2 asb - 230v~ 115v~/60hz 230v~/50hz 480 watts max warning! Risk of hazardous energy! Make proper connections. Avertissement! Energie electrique dangereuse! Faire des connexions propres pour l'hautparleur....

  • Page 15

    - 14 - individual zones bypass trigger all zones 12vdc 1(-) 2(+) voltage selector 4 asb - 115v~ 2 asb - 230v~ 115v~/60hz 230v~/50hz 480 watts max warning! Risk of hazardous energy! Make proper connections. Avertissement! Energie electrique dangereuse! Faire des connexions propres pour l'hautparleur....

  • Page 16

    - 15 - if zones require ultra-high power amplification, ada suggests using pf-2501 power amplifi- ers (250w/ch @ 8 Ω, 450w/ch @ 4Ω, stable to 2Ω) along with an acc-3 ac controller. If zones require driving a great many speakers (up to sixteen pairs @ 8 Ω), ada suggests using a pf-201 (60w/ch @ 8 Ω, ...

  • Page 17

    - 16 - home theater (or recording) set up when working with home theater preamplifiers, whether they are in the form of an av receiver or separate preamplifier and amplifier, you can assign a suite 16 zone output to the theater room. As such, the theater preamplifier can play the same components tha...

  • Page 18

    - 17 - amp trigger jumping on 9-pin d connectors when more than just a few zones require greater power, several ada amplifiers options exist including the ptm-6150 (6 x 150w/ch @ 8 Ω, 250w/ch @ 4Ω, stable to 2Ω), ptm-8150 (8 x 150w/ch @ 8 Ω, 250w/ch @ 4Ω, stable to 2Ω), and ptm-1260 (operating in br...

  • Page 19: V-16 Video Switching Module

    - 18 - v-16 video switching module the v-16 video switching module expands suite 16’s distribution capabilities to include com- posite video as well as audio routing. Much like the p-16 modules, the v-16 can be used in multiples for up to 96 zones of video switching (up to six v-16 modules). Video i...

  • Page 20

    - 19 - v-16 • video i/o module input triggers s 8/16 programmed video input triggers 5-24v ac•dc gnd (-) 1 (+) 2 (+) 3 (+) 4 (+) 1/9 2/10 programmed video triggers the v-16 also features five programmed triggers. The removable 5-pin screw terminal connector features ground (-) on pin 1, and 3- 24v a...

  • Page 21

    - 20 - avp-16 baud rate, zone, & paging settings the avp-16 front panel is remarkably void of clutter. In addition to the main power switch, the front panel rs-232 i/o, there is only a smoked plexiglass plate through which several leds are visible. During setup, this plate may need to be removed to ...

  • Page 22

    - 21 - the compression slope trim pot is used to compress the paging audio input signal. This feature will prevent an input signal that is too high from being broadcast at that level. While each room has its own paging volume level to prevent speaker overdrive, the compression slope adjustment is us...

  • Page 23: Avp-16 Configuration Options

    - 22 - 1/2 asb 115v~ 1/4 asb 230v~ 115v~/60hz • 230v~/50hz 500 watts max caution risk of electric shock do not open attention! Risque de choc electrique. Ne pas ouvrir made in u.S.A. 230v 115v 1 gnd 2 fdbk 3 cntrl 4 +v ada bus® network control i/o main ac input switch ac (10a) warning! Risk of hazar...

  • Page 24

    - 23 - matrix switching - s-video, component, or rgbhv for applications where an installation requires simultaneous switching of multiple discrete video signals, any suite-16 v-16 video module may be set up as a slave card. This is useful for s-video (y & c), component video (y, cr, cb), or hdtv vid...

  • Page 25

    - 24 - if you have a suite-16 for 16 rooms that is switching composite video and you have a compo- nent video switching matrix in a separate avp-16 chassis, then you might opt to use the room group address of 17-32 for the matrix switcher. As such, you could connect the suite-16 audio video system r...

  • Page 26

    - 25 - avp-16 slave-unit configuration options slave audio setup - in addition to the first avp-16, a 2nd chassis w/one p-16 this configuration is in addition to the primary avp-16 and as such, does not require an a-16 audio input module. This chassis adds 16 zones to the primary unit. 1/2 asb 115v~...

  • Page 27: Avp-16 Slave-Unit Setup

    - 26 - 1/2 asb 115v~ 1/4 asb 230v~ 115v~/60hz • 230v~/50hz 500 watts max caution risk of electric shock do not open attention! Risque de choc electrique. Ne pas ouvrir made in u.S.A. 230v 115v 1 gnd 2 fdbk 3 cntrl 4 +v ada bus® network control i/o main ac input switch ac (10a) warning! Risk of hazar...

  • Page 28

    - 27 - avp-16 bottom (master & slave units other than last slave) set master & any slave units other than last slave unit on/off by master avp-16 power switch avp-16 bottom (last slave unit) set last slave unit on/off by master avp-16 power switch avp-16 main & slave unit power-on setup during initi...

  • Page 29

    - 28 - avp-16 ada bus & control wiring suite 16 without other ada components or keypads if you are controlling just an ada suite 16 from a non-ada control interface (i.E. Touch screen control system), you can connect directly to the suite-16’s rear panel rs-232 jack. Please note, that the front pane...

  • Page 30

    - 29 - 1/2 asb 115v~ 1/4 asb 230v~ 115v~/60hz ¥ 230v~/50hz 500 watts max caution risk of electric shock do not open attention! Risque de choc electrique. Ne pas ouvrir made in u.S.A. 230v 115v 1 gnd 2 fdbk 3 cntrl 4 +v ada bus¤ network control i/o main ac input switch ac (10a) warning! Risk of hazar...

  • Page 31: Damaged Wiring Options

    - 30 - damaged wiring options in the event that a cat. 5 cable is damaged, you can still get an mc-5000, mc-5011, mc-3000, mc-3800, mc-3000 od, or mc-3800 od to operate, providing that six of the eight cat. 5 wires are good. To do so, eliminate the first wire and the eighth wire from the rj-45 conne...

  • Page 32: Ir Control of The Suite 16

    - 31 - ir control of the suite 16 ada provides the rc-40 hand-held ir remote control for wire- less infrared control of the suite-16 and source components. This unit features the same button layout as an mc-5000 and like any system keypad, the rc-40 is programmed for a spe- cific room. As such, it c...

  • Page 33: Rf Control

    - 32 - rft-3000 rj-45 cat. 5 cable connector top front b r o w n b r o w n w h i t e b l u e b l u e w h i t e 8 7 6 5 4 3 2 1 rf control ada provides an rf control option for suite 16 systems operat- ing at either 1200 baud or 19200 baud. This involves using a single rft-3000 rf transceiver per sys...

  • Page 34

    - 33 - output level antenna audio output l r tuner 3 output level antenna audio output l r tuner 2 output level antenna audio output l r tuner 1 this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1 this device may not cause harmful interference....

  • Page 35

    - 34 - mc-6000 keypad with video, wh-6000, & tv-6000 the mc-6000 keypad fits a four-gang box and in addition to the mc-5000 rapture keypad, features a small lcd preview display. There are also five navigation buttons below the screen for up, down, right, left, and enter (select) control. The enter b...

  • Page 36

    - 35 - video output (75 Ω) cat-link video input (from wh-6000) pull shunting pin for hi-z input h.F. Gain tv-6000 cat-link video receiver rj-45 cat-link 8 7 6 5 4 3 2 1 video in 1 video in 2 75 Ω hi-z gain trim tx loop out i/o 1 i/o 2 ada bus 4 3 2 1 rj-45 cat-link i/o 3 in rx bus power cat-link 1 h...

  • Page 37: Cmb-1 Clock Module

    - 36 - cmb-1 clock module the cmb-1 clock calendar module is a master clock module which calibrates all system clocks (i.E. Mc- 5000 keypads) on power up and from then on, every hour. While typically powered by the ada bus, the cmb-1 also features a battery backup to maintain time during power outag...

  • Page 38: Mc-5011 Keypad Setup

    - 37 - mc-5011 keypad setup the mc-5011 keypad combines both elegance, function, and price into a single-gang decora bezel. The mc-5011 is only available with a cat-link connector. As such, the mc-5011 must be wired on standard cat. 5 cable. The mc-5011 controls the suite 16 system. You must use the...

  • Page 39: Mc-5000 Keypad Led Setup

    - 38 - mc-5000 keypad led setup the mc-5000 rapture keypad is designed to permit you to select different light colors per button groups. The buttons are grouped together by function and each group has three dip switches associated to that group. The three switches turn on red, green, and blue indivi...

  • Page 40: Mc-5000 Keypad Manual Setup

    - 39 - mc-5000 keypad manual setup the extra button is used to both permit the user to access other keypad functions while permitting the installer to enter the keypad’s program mode. To enter the program mode, press and hold the extra button for 5 seconds. The display will read the keypad’s version...

  • Page 41

    - 40 - 1200 baud rate for code 1117, the display will read baud 1200. If the display maintains baud 1200, the keypad is not communicating with the suite 16. As such, this may be the wrong baud rate setting. 19200 baud rate for code 1118, the display will read baud 19200. If the display maintains bau...

  • Page 42: Mc-5000 Installer Setup

    - 41 - set date - after setting the month, use the > button to advance the display to set date and then press > once. Again the display will read the current date and time, as an example, feb14 23:33. At this time, pressing >> or numeric date. When the desired date is displayed, use the > button to ...

  • Page 43

    - 42 - input configuration while the display reads input config pressing the > button will engage the input configu- ration mode. The display will read: normal input here there are a total of five options, the most common of which the normal input configu- ration option is the most common: normal in...

  • Page 44

    - 43 - party group source selection the party group source selection feature permits multiple rooms to engage to the selected source when a single keypad accesses that source. This feature is used to setup “party” type sources in several rooms when entertaining. In this application, not all sources ...

  • Page 45

    - 44 - irl-5000 once you press the > button while ir learner is displayed, the display will change to read: irl address1 using the >> and button to return to the previous level. While the display reads irl address1, pressing the > button will take you to the next level where the display will read: i...

  • Page 46

    - 45 - exiting trinity tuner setup to exit the trinity tuner from the lowest level, you will need to press the first time will return you to the address level, the second time will return you to ada tuner with the following options available. Ir learner - ada tuner - special cd - lvi - no function u...

  • Page 47

    - 46 - source labels source labels are the names of the sources that are connected to the suite 16. While the keypad buttons have only a few buttons to designate a source name, the keypad’s display can read up to eleven characters. This permits you to better define that component. Whether you are us...

  • Page 48

    - 47 - to completely exit the source label area, press the either the first eight or all sixteen source labels, use the >> or reads: custom label then press the > button. The display will read the first of sixteen inputs. Input 1 using the >> or is on an input whose label you wish to alter, press th...

  • Page 49

    - 48 - rs-232 connections for pc’s & control systems the avp-16 chassis features two rs-232 ports, one on the front of the chassis and a second one on the rear panel. These two rs-232 ports are in parallel. As such only one port can be used at any one time. If you have a pc or external control syste...

  • Page 50

    - 49 - keypad uploader program (mc-5ks uploader) ada’s mc-5ks uploader program is designed to speed you through the process of program- ming keypad button input links, source control links, and source labels. Furthermore, you can retain a saved version of the project as a “.5ks” file type, permittin...

  • Page 51

    - 50 - begin by labeling your inputs. Select an input label, by default labeled 1 through 16, which will then be outlined in blue. You can label each source with only 11 characters..

  • Page 52

    - 51 - now select the source button representative of the eight source buttons on ada keypads and assign a suite 16 input to it. Determine if the keypad button is a normal input or if it will activate a suite 16 party group. Finally, assign the source control option, in this example trinity tuner, m...

  • Page 53

    - 52 - for sources that are controlled by the irl-5000, you can assign both an address and port. For the special cd option, to control and get feedback from the aquarius hard drive server, select the source button and assign a special cd address. For sources that are controlled by the lvi-388 low vo...

  • Page 54

    - 53 - once you have the customer’s mc-5000 configuration established, you can opt to save it as a “.5ks” file type. As such you can reload these settings at a later time. Under file, select save as and enter a customer name with the “5ks” suffix and press save. To upload the settings to the mc-5000...

  • Page 55: Suite 16 Testing & Program

    - 54 - suite 16 testing & program ada has developed a fully functional pc program for the suite-16 system, the suite-16 test- ing & programming software. Using this application, you can control a complete suite-16 system. This program is also ideal for setting up a suite-16 system, permitting you to...

  • Page 56

    - 55 - room control page under the room control tab, you can set and control all of the audio parameters specific to that room. Begin by selecting a room number using the pull-down room window. To update the pc’s display with this room’s status, you will need to press the little square (orange/red) ...

  • Page 57

    - 56 - input selection there are several ways to select a source. You can simply use the input up or input down buttons. You can also directly access inputs numerically. If a room is off or if the system in all off, those buttons will be depressed. When an input is selected, the room turns on. Bass ...

  • Page 58

    - 57 - volume control volume is controlled in two ways, there is the volume up and down commands which will raise and lower volume levels over a range with 40 values (0-40). You can also do a volume direct command which enters a value using the slider control. Much like a touch screen with sliders, ...

  • Page 59

    - 58 - party grouping party grouping delivers to the suite 16 system two functional features. There are a total of four party groups. Much like a room has command sets for selection of input 1, input 2,...,in- put 16, each party group also has an input selection command set for input 1, input 2,...,...

  • Page 60

    - 59 - global room control page the global room control tab features both party group and paging triggers as well as the input level trim controls.. The red button in the lower right hand corner is the update informa- tion request button. Input level trim adjustment the trim level adjustment can low...

  • Page 61

    - 60 - paging control the paging control tab permits you to simulate paging triggers. The first six triggers are only controlled serially. As such, a control code needs to be issued in order to activate triggers 1 through 6. Paging group 7 is the audio sensing trigger. The sensitivity of this trigge...

  • Page 62

    - 61 - video control page the video control tab permits control video direct selection, activation of the four video trig- gers, and also features the settings for video-follow-audio switching. To update this page, press the red button located in the lower left hand corner. For direct video switchin...

  • Page 63

    - 62 - video trigger setup page the video trigger setup tab incorporates the feature sets that determine what events occur when one of the four video triggers is activated. Here, the surveillance feature set of suite 16 becomes obvious. To update this page, press the red box in the lower left hand c...

  • Page 64

    - 63 - ing the front door, and you want to assign these cameras to trigger number 1, select trigger number 1 from the pull down window and then set input 15 and 16 by pressing the appropriate set buttons. To clear these inputs from these triggers, press the clear buttons. To determine what triggers ...

  • Page 65

    - 64 - suite 16 serial protocol v1.4 explanation purpose: this document explains the serial data code structure and operation of the suite 16 multi- room preamplifier. This document is preliminary and is for suite 16 audio card with version 1.4 software. All content subject to change. Discussion: th...

  • Page 66

    - 65 - description of commands: all off powers down all rooms, amplifiers and source equipment; a global shutdown example ‘salofg00 shut system down feedback ‘axalofg00 feedback request ‘galofg00 feedback ‘axalofg00 or ‘asysong00 input up each input up command will advance to the next numbered audio...

  • Page 67

    - 66 - input 1-input 16 directly selects one of the 16 discreet audio inputs for a given room. If the room was off the room will now be turned on and its associated amplifier and source equipment will be acti- vated. Example ‘sad01r01 select audio input 1 for room 1 feedback ‘axad01r01 feedback requ...

  • Page 68

    - 67 - room off shuts down the selected room. If it is the only room on in the system the response will be all off. Example ‘srmofr01 turn off room 1 feedback ‘axrmofr01 or room 1 is off ‘axalofg00 all off when last room turned off feedback request ‘grmofr01 feedback ‘axrmofr01 room 1 is off or ‘axa...

  • Page 69

    - 68 - bass up advances bass by 2db for a given room. The range of bass is +12db to -12db incremented by 2db. When set to 0db bass is flat. No function when room is off. Feedback request al- lowed when room is off. Example ‘sbsupr01 increment bass up by one step in room 1 feedback ‘axb###r01 current...

  • Page 70

    - 69 - treble down decrements treble by 2db for a given room. No function when room is off. Feedback request allowed when room is off. Example ‘strdnr01 decrement treble by 1 step in room 1 feedback ‘axt###r01 current treble value for room 1 request feedback ‘gtrdnr01 feedback ‘axt###r01 current tre...

  • Page 71

    - 70 - tone recall 1-4 allows you to recall 4 pre-stored combinations of bass, treble, loudness contour and stereo enhance. No function when room is off. Feedback request allowed when room is off. Example ‘stnr1r01 recall tone 1 settings for room 1 feedback ‘axb###r01 current bass value for room 1 ‘...

  • Page 72

    - 71 - loudness contour off turns off loudness contour mode for a given room. No function when room is off. Feedback request allowed when room is off. Example ‘sldofr01 turn off loudness contour for room 1 feedback ‘axldofr01 feedback request ‘gldofr01 feedback ‘axldonr01 or ‘axldofr01 loudness cont...

  • Page 73

    - 72 - mono input right selects right source input to be routed to left and right speakers for a given room no function when room is off. Feedback request allowed when room is off. Example ‘sminrr01 right input to left and right speakers in room 1 feedback ‘axminrr01 feedback request ‘gminrr01 feedb...

  • Page 74

    - 73 - balance store 1-2 allows you to store 2 balance settings for a given room. The current active balance setting is stored. No function when room is off. Feedback request allowed when room is off. Example ‘sbls1r01 store current room 1 balance setting in balance recall 1 feedback ‘a1b###r01 feed...

  • Page 75

    - 74 - party set 1-4 allows any given room to become a “member” of party 1-4 example ‘spts1r01 set room 1 to be a member of party 1 feedback ‘axpts1r01 feedback request ‘gpts1r01 feedback ‘axpts1r01 or room 1 is in party 1 ‘axptc1r01 room 1 is not in party 1 party clear 1-4 clears a given room from ...

  • Page 76

    - 75 - page volume preset allows a predetermined paging level to be set for a given room. The command structure is pv## where ## is the preset page volume 00 to 40 example ‘spv40r01 set page volume to maximum for room 1 feedback ‘axpv40r01 feedback request ‘gpv##r01 feedback ‘axpv##r01 current page ...

  • Page 77

    - 76 - page group 1-6 serial controlled paging of any group 1-6. Must be followed by the page off command when page completed. For audio feedback prevention, include the room number after the g to temporarily exclude it from the group. Example ‘sp#ong00 or page a group where # = 1 to 6 ‘sp#ong30 pag...

  • Page 78

    - 77 - manual page (aka group 8) contact closure controlled page. All members of group 8 are paged. When contacts are released paging is complete. Feedbackwhen activated ‘axp8ong00 when deactivated ‘axpgofg00 maximum allowable volume allows you to set a maximum allowable volume level per room. The c...

  • Page 79

    - 78 - reset to factory default values resets all parameters to factory default values. All volumes and volume presets are set to half, bass and treble set flat, balance and balance presets set to equal, stereo enhance off, loudness contour off, stereo mode on, mute off, all rooms off, all input tri...

  • Page 80

    - 79 - update all room controls this is an abridged request that only replies with certain room parameters for all rooms as follows: example ‘galrcg00 feedback *this feedback sequence is repeated for each room ‘axv###r## volume ‘axb###r## bass ‘axt###r## treble ‘axb###r## balance ‘ax####r## current ...

  • Page 81

    - 80 - ‘ax####r01 current input or room off or all off ‘axvpo#r01 volume preset on/off ‘axmv##r01 max volume ‘axmto#r01 mute on or off ‘ax ####r01 stereo or mono in l or mono in r ‘axldo#r01 loudness contour on/off ‘axseo#r01 stereo enhance on/off ‘av1###r01 volume preset 1 ‘av2###r01 volume preset ...

  • Page 82

    - 81 - character echo command the character echo command is useful when data is to be sent from one remote control device to another. Normally a remote control device can only send data to the suite 16 unit to request a function. For specialized functions such as label copying, the character echo co...

  • Page 83

    - 82 - 3. Video following audio/independant video has feedback this function is assignable for every input in any given room. That way if only a few of the inputs are video components only those set will follow audio selections. If following is set for any input in a room, the remaining inputs not s...

  • Page 84

    - 83 - 8. Video trigger dwell time has feedback this serial command globally sets the dwell time. Dwell time is the interval that a video input selection remains on until it switches to the next in sequence. Range is 1-60 seconds. Code examples ‘sdwelg05 set dwell time to 5 seconds ‘sdwelg60 set dwe...

  • Page 85: Suite 16 Ascii Codes

    - 84 - string start action prefix part 2 global part 3 function character do (set) get function r01 to r99 input up ‘ s g inup r01 input down ‘ s g indn r01 input 1 ‘ s g ad01 r01 input 2 ‘ s g ad02 r01 input 3 ‘ s g ad03 r01 input 4 ‘ s g ad04 r01 input 5 ‘ s g ad05 r01 input 6 ‘ s g ad06 r01 input...

  • Page 86

    - 85 - input level trim 1 ‘ s g it01 g## input level trim 2 ‘ s g it02 g## input level trim 3 ‘ s g it03 g## input level trim 4 ‘ s g it04 g## input level trim 5 ‘ s g it05 g## input level trim 6 ‘ s g it06 g## input level trim 7 ‘ s g it07 g## input level trim 8 ‘ s g it08 g## input level trim 9 ‘ ...

  • Page 87

    - 86 - suite 16 video card protocol v1.1 01 - 16 01 - 96 set video following start set/get input function input # output function room # video tracks audio input ‘ s fs 01 r 01 video tracks nothing (goes off) ‘ s fc 01 r 01 get curent following setting for input ‘ g fs or fc 01 r 01 01 - 16 01 - 96 ...

  • Page 88

    - 87 - appendix a - mc-5000 setup flow charts code: _ _ _ _ extra fm1 fm2 am cd1 cd2 dss dvd aux using the 8 source buttons enter the code "1111 ", w here 1 is the source on the far left (fm1) and eight is on the far right (aux) code: 1 1 1 1 press & hold extra check keys reads function extra suite-...

  • Page 89

    - 88 - code: _ _ _ _ extra fm1 fm2 am cd1 cd2 dss dvd aux using the 8 source buttons enter the code "1 1 1 5", where 1 is the source on the far left (fm1) and eight is on the far right (aux) code: 1 1 1 5 press & hold extra clock set extra suite-16 system mc-5000, mc-6000, mc-3000 od, mc-3800 od pro...

  • Page 90

    - 89 - code: _ _ _ _ extra fm1 fm2 am cd1 cd2 dss dvd aux using the 8 source buttons enter the code "1867", where 1 is the source on the far left (fm1) and eight is on the far right (aux) code: 1 8 6 7 press & hold extra inst aller >> input config > source cntrl > source label > check setup > progra...

  • Page 91

    - 90 - code: _ _ _ _ extra fm1 fm2 am cd1 cd2 dss dvd aux using the 8 source buttons enter the code "1867", where 1 is the source on the far left (fm1) and eight is on the far right (aux) code: 1 8 6 7 press & hold extra inst aller >> input config > source cntrl > source label > check setup > progra...

  • Page 92

    - 91 - code: _ _ _ _ extra fm1 fm2 am cd1 cd2 dss dvd aux using the 8 source buttons enter the code "1867", where 1 is the source on the far left (fm1) and eight is on the far right (aux) code: 1 8 6 7 press & hold extra inst aller >> input config > source cntrl > source label > check setup > progra...

  • Page 93

    - 92 - code: _ _ _ _ extra fm1 fm2 am cd1 cd2 dss dvd aux using the 8 source buttons enter the code "1867", where 1 is the source on the far left (fm1) and eight is on the far right (aux) code: 1 8 6 7 press & hold extra inst aller >> input config > source cntrl > source label > check setup > progra...

  • Page 94

    - 93 - code: _ _ _ _ extra fm1 fm2 am cd1 cd2 dss dvd aux using the 8 source buttons enter the code "1867", where 1 is the source on the far left (fm1) and eight is on the far right (aux) code: 1 8 6 7 press & hold extra inst aller >> input config > source cntrl > source label > check setup > progra...

  • Page 95

    - 94 - appendix b - system specifications avp-16 size & weight (with a-16, p-16, & v-16 modules) width: 19” eia rack mount height: 5.25” (3 rack spaces) depth: 20” weight: 26 lbs electrical specifications rca inputs: 47k Ω normal input volt.: 2v maximum input volt: 2.8v balanced paging input: 600 Ω ...

  • Page 96

    - 95 - appendix c - 9 pin d connector information the following diagram indicates the pin connections for the 9-pin d connectors on used for zone low voltage triggering. The p-16 preamplifier module, the ptm-1225 and the ptm-1260 all feature female jacks with the same pin configurations. The db-9 te...