1. DL manuals
  2. B&B Electronics
  3. Computer Hardware
  4. iMcV-LIM
  5. Operation Manual

B&B Electronics iMcV-LIM Operation Manual

Manual is about: iMcV-Modules

Summary of iMcV-LIM

  • Page 1

    Imcv-modules operation manual above illustrations are representative; some minor differences may be present in actual product.

  • Page 2

    Ii fcc radio frequency interference statement imcv-s2mm/1250 and imcv-s2sm/1250 this equipment has been tested and found to comply with the limits for a class a computing device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interfer...

  • Page 3

    Iii limited lifetime warranty effective for products of b&b electronics shipped on or after may 1, 2013, b&b electronics warrants that each such product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable solely to the original user a...

  • Page 4

    Iv table of contents fcc radio frequency interference statement .............................................. Ii limited lifetime warranty .............................................................................. Iii about the imcv-modules .........................................................

  • Page 5

    1 about the imcv-modules imcv-modules are snmp-manageable and install in the modular, snmp- manageable imediachassis series in the unmanaged mediachassis series. The following media conversion and fiber mode conversion imcv modules are described in this manual: imcv-pim ethernet module providing a s...

  • Page 6

    2 leds on imcv-pim (-10) the led functions are as follows: pwr glows green when unit has power. Lnk (rj-45) glows green if link is established on the twisted pair port (located on rj-45). Act (rj-45) glows amber when data is being passed on the twisted pair (located on rj-45). Lnk glows green when l...

  • Page 7

    3 leds on imcv-lim the led functions are as follows: ll glows green when fx linkloss is enabled. Lnk glows green when a link is established on the port. Xmt blinks green when port is transmitting data. Rcv blinks yellow when port is receiving data. Fa* glows green when fiberalert is enabled. *fibera...

  • Page 8

    4 configuration instructions many imcv-modules have user-configurable features (e.G., fiberalert, linkloss, auto negotiation, etc.). Refer to the chart for information on available features on each module. Instructions for configuring both managed (via an snmp- compatible management application such...

  • Page 9

    5 about linkloss, fiberalert, and pulsing fiberalert imcv-lim tx/fx and tx/ssfx -30 board imcv-pim tp/fo - 10 board.

  • Page 10

    6 some imcv-modules include advanced troubleshooting features that help locate silent failures on the network. Troubleshooting features include: fo/fx linkloss (a.K.A. Fiber linkloss or linkloss) tp/tx linkloss (a.K.A. Twisted pair linkloss or reverse linkloss) fiberalert pulsing fiberalert it is im...

  • Page 11

    7 tp/tx linkloss is another troubleshooting feature. When a fault occurs on the twisted pair segment of a conversion, tp/tx linkloss detects the fault and passes this information to the fiber segment. If a media converter is not receiving a twisted pair link, tp/tx linkloss disables the transmitter ...

  • Page 12

    8 tx linkloss remote site only twisted pair fiber fx linkloss home site (or both) fiber twisted pair if unsure of how best to implement these features in a specific configuration, please contact b&b electronics technical support at (800) 346-3119 (u.S./canada), +353 91 792444 (europe) or via e-mail ...

  • Page 13

    9 end to end connection switch mcpc tx/fx half-duplex manually configure hdx auto negotiation off full-duplex manually configure fdx auto negotiation off full-duplex auto negotiation on auto negotiation on configure auto negotiation on an imcv-lim by adjusting the dip switch setting (for unmanaged m...

  • Page 14

    10 5 to 95% (non-condensing); 0 to 10,000 ft. Altitude dimensions single slot imcv-module b&b electronics technical support tel: (800) 346-3119 (in the u.S. And canada) monday-friday, 7:00am- 7”00pm cst +353 91 792444 (europe) monday through friday 8:00am - 5:00pm gmt fax: (815) 433-5109 u.S. And ca...

  • Page 15

    11 fiber optic cleaning guidelines fiber optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules. 1. Use fiber p...

  • Page 16

    12 certifications ce: the products described herein comply with the council directive on electromagnetic compatibility (2004/108/ec) for further details, contact b&b electronics. European directive 2002/96/ec (weee) requires that any equipment that bears this symbol on product or packaging must not ...

  • Page 17: International Headquarters

    International headquarters b&b electronics 707 dayton road ottawa, il 61350 usa phone (815)433-5100 — general fax (815) 433-5105 email: support@bb-elec.Com website: www.Bb-elec.Com european headquarters b&b electronics westlink commercial park oranmore, co. Galway, ireland phone +353 91-792444 — fax...