Summary of ESWGP206-2SFP-T
Page 1
Eswgp206‐2sfp‐t user manual.
Page 2: International Headquarters
2 international headquarters b+b smartworx. 707 dayton road ottawa, il 61350 usa phone (815) 433-5100 -- general fax (815) 433-5105 website: www.Imcnetworks.Com support@bb-smartworx.Com european headquarters b+b smartworx westlink commercial park oranmore, co. Galway, ireland phone +353 91-792444 --...
Page 3
3 contents figures ........................................................................................................................................................................... 4 tables .......................................................................................................
Page 4
4 figures figure 1. Poe reset ......................................................................................................................................................... 9 figure 2. Din rail mounting .........................................................................................
Page 5
5 radio frequency interference statement this equipment has been tested and found to comply with the limits for a class a computing device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in ...
Page 6
6 warranty effective for products of b+b smartworx shipped on or after may 1, 2013, b+b smartworx warrants that each such product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable solely to the original user and is not transferable....
Page 7
7 contents of package the package includes: • b+b ethernet switch with attached din rail clip • printed quick start guide • 4-panel mounting clips with screws you may download the user manual at any time from the b+b smartworx/imc networks web site: www.Imcnetworks.Com.
Page 8
8 product description the eswgp206-2sfp-t is a plug-and-play, poe+, unmanaged, industrial ethernet switches with ip30 protection. It provides four 10/100/1000mbps copper ports and two sfp ports for 1000mbps speed. The fiber sfp port (port #6) can accommodate both single-mode and multi-mode fiber. Th...
Page 9
9 hardware led description led status description pwr (p1, p2) green on power applied sta green flashing system state lnk led green on link established green flashing data is being transmitted spd led green on 1000 mbps orange on 100 mbps off 10 mbps max led green on poe power over max load poe+(1/2...
Page 10
10 din rail mounting the din rail mounting clips are connected to the switch when shipped and are ready to be mounted on a 35mm size din rail. Figure 2. Din rail mounting panel mounting figure 3. Panel mounting.
Page 11
11 rj45 ethernet connection all copper ports on the switch support the auto cross feature, which allows the end user to use a straight-through or crossover cable. Figure 4. Ethernet connection.
Page 12
12 figure 5. Ethernet connection pin assignments pin# signal direction 10/100m poe & poe+ pinout (alt-a) 1 out* v+ 2 out* v+ 3 in* v- 4 5 6 in* v- 7 8 table 2. Pin assignments.
Page 13
13 sfp installation and connection to connect the transceiver and fiber cable, follow the steps below. The sfp port is not proprietary. Any msa-compliant 1000mbps fiber sfp can be installed in the port. (note: sfp modules typically offer an lc fiber connector). One of the sfp ports allows fiber sfps...
Page 14
14 figure 7. Lc connector to the transceiver last, remove the sfp and gently pull out of the cage manually. Power input connections eswgp206-2sfp-t accepts 24v~52vdc input voltage using terminal blocks. Figure 8. Power input connections.
Page 15
15 specifications technology standard ieee802.3, 802.3u, 802.3x, 802.3z, 802.3ab, 802.3af/at processing type store and forward broadcast storm disabled flow control full duplex flow control, half duplex back pressure control protocols csma/cd (carrier sense multiple access/collision detect) switch p...
Page 16
16 certifications safety iec/ul/en60950-1 emi ce, fcc part 15, en55022: class a ce en61000-6-4 (industrial) ems ce en61000-4-2 (esd) ce en61000-4-3 (rs) ce en61000-4-4 (eft) ce en61000-4-5 (surge) ce en61000-4-6 (cs) ce en61000-4-8 ce en61000-4-11 ce en61000-6-2 (industrial) free fall iec60068-2-32 ...
Page 17
17 compliance and disposal the products described here in comply with the council directive on electromagnetic compatibility (2004/108/ec) and the council directive on electrical equipment designed for use within certain voltage limits (2006/95/ec). Will be certified for information technology equip...
Page 18
18 dimensional drawing figure 9: dimensional drawing.
Page 19
19 b+b smartworx technical support phone: 1-800-346-3119 (monday - friday, 7 a.M. To 5:30 p.M. Cst) fax: 815-433-5109 email : support@bb-smartworx.Com web: www.Imcnetworks.Com.