1. DL manuals
  2. B+B SmartWorx
  3. Network Router
  4. SmartFlex SR300
  5. User Manual

B+B SmartWorx SmartFlex SR300 User Manual

Manual is about: LAN Industrial Router

Summary of SmartFlex SR300

  • Page 1

    Lan industrial router smartflex sr300 user’s manual.

  • Page 2

    Headquarters international headquarters advantech b+b smartworx 707 dayton road ottawa, il 61350 usa phone (815) 433-5100 – general fax (815) 433-5105 websites www.Bb-smartworx.Com www.Bb-smartsensing.Com support@bb-elec.Com cellular routers office advantech b+b smartworx s.R.O. Sokolska 71 562 04, ...

  • Page 3

    Used symbols used symbols danger – information regarding user safety or potential damage to the router. Attention – problems that can arise in specific situations. Information, notice – useful tips or information of special interest. Gpl licence source codes under gpl licence are available free of c...

  • Page 4

    Contents contents 1 safety instruction 2 2 weee directive 3 3 router description 4 4 contents of package 5 5 router design 6 5.1 router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5.2 delivery identification . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 5

    Contents 7.3 type tests and environmental conditions . . . . . . . . . . . . . . . . . . . . . . 26 7.4 technical parameters of wifi . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7.5 technical parameters of i/o port . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7.6 technical pa...

  • Page 6

    List of figures list of figures 1 contents of package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 version switch (plastic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 version switch and wifi (plastic) . . . . . . . . . . . . . . . . . . . . . . . . . 6 4...

  • Page 7

    List of tables list of tables 1 router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 delivery identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 order codes overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 8

    1. Safety instruction 1. Safety instruction please, observe the following instructions: • the router must be used in compliance with all applicable international and national laws and in compliance with any special restrictions regulating the utilization of the router in prescribed applications and ...

  • Page 9

    2. Weee directive 2. Product disposal instructions the weee (waste electrical and electronic equipment: 2002/96/ec) directive has been introduced to ensure that electrical/electronic products are recycled using the best available recovery techniques to minimize the impact on the environment. This pr...

  • Page 10

    3. Router description 3. Router description lan industrial router smartflex sr300 is an ideal device for the realization of a secure connection of two local area networks (lans). Interconnection is carried out using two eth- ernet 10/100 interfaces and secure tunnel (ipsec, openvpn, l2tp). The other...

  • Page 11

    4. Contents of package 4. Contents of package basic delivered set of router includes: • router, • power supply, • crossover utp cable, • 2.4 ghz wifi antenna (only for version with wifi), • loose power and i/o connector (+8 pins 1 ), • clip for the din rail, • paper start guide. Figure 1: contents o...

  • Page 12

    5. Router design 5. Router design 5.1 router versions smartflex sr300 router is supplied in the following versions (see table below). All versions are available in plastic or metal box according to customer requirements. All versions are available with poe pd (power over ethernet – powered device) s...

  • Page 13

    5. Router design 5.2 delivery identification trade name type name other smartflex sr300 smartflex router in a plastic or metal box table 2: delivery identification figure 6: label examples 5.3 order codes order codes overview is shown in the table below. Product name order code features – interfaces...

  • Page 14

    5. Router design letter "y" – type of the router box type of box number "y" in code plastic 1 metal 2 table 5: type of router box letter "z" – type of the power supply connector type of power supply number "z" in code europe 1 uk & ireland 2 australia 3 north america 4 without accessories 0 table 6:...

  • Page 15

    5. Router design 5.4 basic dimensions of the router box figure 7: basic dimensions of the router box 5.5 mounting recommendations • possibility to be put on a work surface, • din rail en 60715 with included clip cpd3 (or ckd2 for metal version). For the most of applications with a built-in router in...

  • Page 16

    5. Router design 5.6 removing from the din rail din holder is suitable for din rail according to en 60715 standard only. Default position of cpd3 holder (or ckd2 holder for metal version), which is used for mounting the router on a din rail, is shown in the following figure: figure 8: default positi...

  • Page 17

    5. Router design 5.7 description of the rear panel the rear panel contains only one holder for sd card (sd) and rst button used to restore default configuration and reboot the router. 5.8 description of the front panel on the front panel is the following: caption connector description pwr 2-pin conn...

  • Page 18

    5. Router design 5.8.1 status indication about router status inform nine led indicators on the front panel. Each eth port has two additional leds that provide information about port status. Caption color state description pwr green blinking on fast blinking router is ready starting of the router upd...

  • Page 19

    5. Router design 5.8.2 power connector pwr panel socket 2-pin. Pin number signal mark description 1 gnd(-) negative pole of dc supply voltage 2 vcc(+) positive pole of dc supply voltage (+10 to +60 v dc) table 10: connection of power connector figure 11: power connector power supply for the router m...

  • Page 20

    5. Router design 5.8.3 antenna connector wifi if the router is equipped with wifi module on the customer’s request, appropriate antenna is connected to the reverse sma connector (wifi). The extarnal antenna is connected by screwing this antenna to the reverse sma connector on the front panel of the ...

  • Page 21

    5. Router design changing the microsd card: • use the flat end of a spudger, or your fingernail, to press the microsd card slightly deeper into its slot until you hear a click. • after the click, release the card and it will pop out of its slot. • remove the microsd card and push any other microsd c...

  • Page 22

    5. Router design crossover utp cable (ethernet cable) plug into the rj45 connector labeled as eth0 or eth1 (see figure below). Figure 16: connection of ethernet cable the insulation strength of ethernet ports from each other and from the rest of the router (grounding) is dependent on the router vers...

  • Page 23

    5. Router design the poe pd parameters can be found in chapter 7.6 . The poe led on the front panel of the router turns on with the green light on the voltage present in an ethernet port so the user knows the router can be poe powered. You can still power the router with this connector even if the r...

  • Page 24

    5. Router design 5.8.7 usb port panel socket usb-a. Pin signal mark description data flow direction 1 +5 v positive pole of 5 v dc supply voltage, 0.5 a 2 usb data - usb data signal – negative pole input/output 3 usb data + usb data signal – positive pole input/output 4 gnd negative pole of dc suppl...

  • Page 25

    5. Router design binary inputs • characteristics of inputs: logical 0 / 1 ∗ voltage current web interface status log. 1 max 3 v 0.4 ma off log. 0 min 5 v 0.7 ma on log. 0 type 12 v 2 ma on log. 0 max 60 v 7 ma on table 16: characteristics of inputs ∗ the binary input status in the shell returned via...

  • Page 26

    5. Router design 5.8.9 reset when pwr led starts flashing on the front panel, it is possible to restore the default con- figuration of the router by pressing the rst button on the rear panel. After pressing this button the default configuration is restored and then router reboots (green led will be ...

  • Page 27

    5. Router design 5.9 interfaces description there are available versions with one of the following interfaces: • switch interface 5.9.1 switch interface three lan ports of switch interface for smartflex routers (rj45 connectors for connect- ing ethernet devices) act as a typical switch device. This ...

  • Page 28

    6. First use 6. First use 6.1 connecting the router before first use before putting the router into operation it is necessary to connect all components which are required to run your applications. The router can not operate without connected power supply. Figure 25: router connection 22.

  • Page 29

    6. First use 6.2 start the router is put into operation when the power supply is connected to this router. By default, the router will automatically start to log on to the default apn. Dhcp server will start to assign addresses for devices on the ethernet port eth0. Router behavior can be changed vi...

  • Page 30

    6. First use after successfully entering login information user gains access to the router via his internet browser. Figure 28: router web interface a detailed description of the router settings via the web interface can be found in the document configuration manual for smartflex routers. 24.

  • Page 31

    7. Technical parameters 7. Technical parameters 7.1 basic parameters smartflex sr300 temperature range operating storage -40 ◦ c to +80 ◦ c -40 ◦ c to +85 ◦ c cold start -40 ◦ c humidity operating storage 0 to 95 % relative humidity non condensing 0 to 95 % relative humidity non condensing altitude ...

  • Page 32

    7. Technical parameters 7.3 type tests and environmental conditions phenomena test description test levels esd en 61000-4-2 enclosure contact enclosure air ± 6 kv (crit. A) ± 8 kv (crit. A) rf field am modulated iec 61000-4-3 enclosure 20 v/m (crit. A) (80 – 2700 mhz) fast transient en 61000-4-4 sig...

  • Page 33

    7. Technical parameters 7.4 technical parameters of wifi wifi antenna connector r-sma – 50 ohms supported wifi band 2.4 ghz, 5 ghz standards 802.11a, 802.11b, 802.11g, 802.11n 2.4 ghz supported channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 5 ghz supported channels 36, 40, 44, 48, 52, 56, 60, 64...

  • Page 34

    7. Technical parameters 7.6 technical parameters of power over ethernet (poe) standards ieee 802.3at-2009 (poe+) and ieee 802.3af-2003 (poe) supported. Cabling needed is category 5, up to 12.5 Ω. It is possible to use a passive poe injector. Poe pd: parameters for opposite pse input voltage range 42...

  • Page 35

    8. Recommended literature 8. Recommended literature [1] advantech b+b smartworx: start guide, [2] advantech b+b smartworx: configuration manual for smartflex routers. 29.

  • Page 36

    9. Troubleshooting 9. Troubleshooting if you can not connect to the router from your pc, your network card may be configured the way it is not possible to connect to the router. Take one or more of the following steps to solve the problem: • select the communication rate 10 mb/s in the properties of...

  • Page 37

    9. Troubleshooting • the operator may not provide the address of dns server and without dns server’s adress it is impossible to connect to the dyndns.Org server. There will be these messages in the system log: – dyndns daemon started – error resolving hostname: no such file or directory – connect to...

  • Page 38

    10. Customers support 10. Customers support 10.1 global customer support you can find up to date information about this product on our website: www.Bb-smartcellular.Eu upkeep-advices: • the sim-card must be handled carefully as with a credit card. Don’t bend, don’t scratch on this and do not expose ...