1. DL manuals
  2. B&D
  3. Garage Door Opener
  4. 1140
  5. Instructions Manual

B&D 1140 Instructions Manual

Manual is about: Chamberlain Instructions Garage Door Opener

Summary of 1140

  • Page 1

    Qld office: 17 oasis court clontarf 4019 (07) 3883-0200 nsw office: 34-36 marigold street revesby 2212 (02) 9722 5555 vic/tas office: 147-153 canterbury road kilsyth 3137 (03) 9237 7766 b&d doors new zealand: 70 allens road easttamaki auckland, new zealand (09) 273 8600 www.Bnd.Co.Nz sa office: 23 f...

  • Page 2: Warn

    2 introduction 2-7 safety rule review........................................................2 preparing your garage door ........................................3 tools needed ...............................................................3 planning ....................................................

  • Page 3: Warn

    3 pliers wire cutters claw hammer hack saw screwdriver adjustable end wrench locking pliers 13mm, 11mm, and 6mm sockets and wrench drill tape measure 2 1 stepladder pencil 8mm, 5mm, and 4mm drill bits carpenter's level to avoid damage to the garage door and opener, disable locks before installing an...

  • Page 4

    Safety reversing sensor horizontal and vertical reinforcement is needed for lightweight garage doors (fibreglass, steel, aluminum, door with glass panels, etc.). See page 21 for details. Support bracket & fastening hardware is required. See page 17. — — — — — — — — door centre header wall safety rev...

  • Page 5

    5 access door gap between floor and bottom of door must not exceed 6mm. Safety reversing sensor the chamberlain group, inc. One-piece door with track installation (cable -usa) 3/3/93 header bracket header sleeve bracket door bracket straight door arm curved door arm trolley emergency release rope & ...

  • Page 6

    6 your garage door opener is packaged in two cartons which contains the motor unit and the parts illustrated below. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for assembly and installation is shown on the next page. Save the carton and pack...

  • Page 7

    Hardware inventory separate all hardware and group as shown below for the assembly and installation procedures. 7 spring /trolley nut (1) master link (2) assembly installation notice handle rope lock washer 8mm (7) hex screw 8mm x 20mm (4) nut 8mm (7) carriage bolt 8mm x 65mm (2) screw (2) washered ...

  • Page 8

    8 assembly step 1 assemble the rail note: if your opener came with a one piece rail, proceed to assembly step 2, page 9. Grease inside edges of rail brace sections. Place rail pieces on flat surface for assembly. All four rail sections are interchangeable. Slide rail braces onto rail section. Connec...

  • Page 9: Warn

    9 assembly step 3 attach chain spreader attach chain spreader to opener with phillips pan head screws. Chain spreader phillips pan head screws opener to avoid serious damage to opener, only use screws mounted in top of motor unit. W warn arning ing caution caution attention attention avertissement a...

  • Page 10

    Bolt trolley stop bolt hole lock washer nut bolt nut lock washer washered bolt sprocket 2 stops 4 sprocket spreader stops spreader screwdriver tip nut ring wrench spring nut header sleeve screwdriver tip nut ring wrench spring nut header sleeve fasten rail to opener set chain tension 10 114a2845 114...

  • Page 11: Ning

    11 important installation instructions 1. Read and follow all installation warnings and instructions. 2. Install garage door opener only on properly balanced and lubricated garage door. An improperly balanced door may not reverse when required and could result in severe injury or death. 3. All repai...

  • Page 12: Warn

    12 installation step 1 determine the header bracket location installation procedures vary according to garage door types. Follow the instructions which apply to your door. Sectional door and one-piece door with track 1. Close the door and mark the inside vertical centreline of the garage door. 2. Ex...

  • Page 13

    13 one piece door without track 1/30/92 - 4/7/92 header wall vertical centreline vertical centreline of garage door 40mm reinforcement board unfinished ceiling optional ceiling mount for header bracket structural supports 40mm reinforcement board one-piece door without track 1. Close the door and ma...

  • Page 14

    14 installation step 2 install the header bracket wall header bracket installation • centre the bracket on the vertical guideline with the bottom edge of the bracket on the horizontal line (with the arrow pointing toward the ceiling). • mark all of the bracket holes. Drill 4.5mm (3/16") pilot holes ...

  • Page 15: Warn

    15 ring fastener (2) temporary support garage door header wall header bracket header sleeve bracket clevis pin 8mm x 13mm (2) ring fastener ring fastener clevis pin 8mm x 13mm clevis pin 8mm x 13mm header sleeve bracket rail hardware shown actual size installation step 3 attach the rail to the heade...

  • Page 16: Warn

    16 top of motor unit header bracket top of door door one-piece door without track • with the door fully open and parallel to the floor, measure the distance from the floor to the top of the door. • using a stepladder as a support, raise the top of the opener to this height. • the top of the door sho...

  • Page 17

    17 114a2845 installation step 6 install the door control locate the door control within sight of the door at a minimum height of 1.5m where small children cannot reach, and away from all moving parts of the door and door hardware. 1. Strip 6mm of insulation from one end of the bell wire. Connect it ...

  • Page 18: Warning

    18 wiring instructions for accessories • place entrapment warning label on the inside of door as a reminder of safe operating procedures. Place the manual release/safety reverse test label in plain view on the inside of the garage door. To prevent possible serious injury or death from electrocution:...

  • Page 19: Warn

    19 114a2845 overhand knot emergency release handle trolley release arm notice the chamberlain group, inc. Figure 16 - manual release 4210e - 3/8/93 rope trolley • to prevent possible serious injury or death from a falling garage door: – if possible, use emergency release handle to disengage trolley ...

  • Page 20

    20 invisible light beam protection area the chamberlain group, inc. Safety sensor instruction sheet page 1 protector system disk #1 (yellow) 11/5/91 - 1/15/92 wing nut sensor beam 100-150mm max. Above floor sensor beam 100-150mm max. Above floor facing the door from inside the garage installation st...

  • Page 21: Warn

    21 carriage bolt 8mm x 65mm nut 8mm lock washer 8mm sheet metal screw hardware shown actual size 114a2845 fibreglass, aluminum or lightweight steel garage doors will require reinforcement before installation of door bracket. To prevent damage to garage doors reinforce inside of door with angle iron ...

  • Page 22

    22 carriage bolt 8mm x 65mm nut 8mm lock washer 8mm sheet metal screw hardware shown actual size 114a2845 header wall vertical centreline of garage door finished ceiling optional placement of door bracket header bracket door bracket 2x4 support for a door with no exposed framing, or for the optional...

  • Page 23

    23 installation step 12 connect door arm to trolley follow instructions which apply to your door type as illustrated below and on the following page. Sectional doors only • make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley...

  • Page 24

    All one-piece doors assemble the door arm: • fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • with the door closed, connect the straight door arm section to the door bracket with the 8mm x 32mm clevis pin. • secure with a ring f...

  • Page 25: Warn

    25 adjustment step 1 limit adjustment run the opener through a complete travel cycle. Force adjustments are not necessary when the door opens and closes completely and doesn't reverse unintentionally in the fully closed position. Locate the button on the back panel of motor unit. Note: if the operat...

  • Page 26: Warn

    Adjustment step 2 adjust the force the force, as measured on the closing edge of the door, should not exceed 400n (40kg). If the closing force is measured to more than 400n, a safety infrared reversing sensor must be installed see step 3 on page 27. The force setting button is located on the back pa...

  • Page 27: Warn

    Adjustment step 3 test the safety reverse system test • with the door fully open, place a 40mm board on the floor, centered under the garage door. • operate the door in the down direction. The door must reverse on striking the obstruction. Adjust • if the door stops on the obstruction, it is not tra...

  • Page 28: Ning

    28 using your garage door opener your opener will operate with up to twelve remote control transmitters, one entry keypad, and one dip- switch code transmitter. If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in the programming section. Activate your op...

  • Page 29: Warn

    29 to open the door manually disconnect the trolley: the door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually. The lockout feature prevents the trolley from reconnecting automati...

  • Page 30

    Troubleshooting 1. Opener doesn't operate from either door control or remote: • does the opener have electric power? Plug lamp into outlet. If it doesn't light, check the fuse box or the circuit breaker. (some outlets are controlled by a wall switch.) • have you disengaged all door locks? Review ins...

  • Page 31

    31 to erase all codes from opener receiver memory to deactivate any unwanted remote, first erase all codes: press and hold the “learn” button on opener until the smart indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wi...

  • Page 32

    114a2845 ©2005, all rights reserved printed in mexico warranty controll-a-door ® automatic garage door opener 1. Definitions ‘b&d’ means (a) in australia - b&d doors of 17 oasis court clontarf, queensland 4019 (b) in new zealand - b&d doors (nz) ltd of 70 allens road east tamaki auckland, which is a...