- DL manuals
- B&D
- Door Opening System
- Controll-A-Door Advance
- Instruction Manual
B&D Controll-A-Door Advance Instruction Manual
Summary of Controll-A-Door Advance
Page 1
Doc #: 161041_00 part #:79151 released: 04/08/2016 sectional door opener instruction manual sdo-3v2 controll-a-door ® s controll-a-door ® s & panelpro ® sdo-4v1 panelpro ®.
Page 2
Controll-a-door ® s & panelpro instruction manual 2 table of contents 1. Installation safety warnings! 3 2. Before you begin 4 examine the conditions in the garage: 4 test the following before commencing installation: 4 3. Tools required 4 4. Kit contents 5 5. Position 5 6. Fit the opener 6 7. Brack...
Page 3
3 controll-a-door ® s & panelpro instruction manual 1. Installation safety warnings! Warning! • the door may operate unexpectedly, therefore do not allow anything to stay in the path of the door. • when operating the manual release while the door is open, the door may fall rapidly due to weak or bro...
Page 4: Diy
Controll-a-door ® s & panelpro instruction manual 4 3. Tools required 2. Before you begin test the following before commencing installation: a. The door must be in good operating condition. B. Manually move the door up and down, the door should move freely without binding or sticking. C. The maximum...
Page 5
5 controll-a-door ® s & panelpro instruction manual 4. Kit contents 1 2 3 4 5 6 7 8 9 10 11 12 13 14 or 15 16 1. 1 x sdo drive unit 2. 1 x wall mount transmitter with battery and screws (cad s only) 3. Transmitters and batteries cad s: 2 x tb6 transmitters panelpro: 3 x tb-5 transmitters, 1 viso cli...
Page 6
Controll-a-door ® s & panelpro instruction manual 6 6. Fit the opener secure c-rail to opener: a. Remove the opener from the box and place onto towel. B. Locate and insert the shaft of drive unit 1 into the c-rail’s sprocket. C. Fix the two track brackets 15 with four (4) m4 x 8 screws 14 supplied i...
Page 7
7 controll-a-door ® s & panelpro instruction manual 8. Perforated angle attach perforated angle (not supplied) or equivalent a. Measure across the ceiling from the centre point 3177mm (+/- 150mm) to find a supporting beam. B. Create a perforated angle which best suits your site. Use a hack saw to cu...
Page 8
Controll-a-door ® s & panelpro instruction manual 8 9. Mounting brackets and arms mounting the door bracket: a. The door bracket locator 7 is placed over the door bracket 8 , on the door’s centre line one-third down the top panel and mounted using m6 or equivalent screws (not supplied), b. Steel doo...
Page 9
9 controll-a-door ® s & panelpro instruction manual 11. Setting the datum position note: the door and shuttle must be engaged into the chain index. The door should be open approximately half way. Note: if safety beams are to be used they must be installed before setting the travel limits. Adjust the...
Page 10
Controll-a-door ® s & panelpro instruction manual 10 12. Safety testing test the close cycle a. Press the operate button to open the door. B. If the door closes, press the operate button to stop the door, then press operate again to open. C. Place a piece of timber approximately 40mm high (or the op...
Page 11
11 controll-a-door ® s & panelpro instruction manual safety beams a safety beam kit may be fitted to this opener. When this option is fitted, the operation of this device is such that if an object (i.E car, child etc) blocks the infra-red beam, then the garage door opener will not close the door aut...
Page 12
Controll-a-door ® s & panelpro instruction manual 12 14. Coding a transmitter storing the transmitter code the opener can only operated from remote control transmitters that have been programmed into its memory. Up to 64 codes can be stored in the memory. A. Press the door code button and release. T...
Page 13
13 controll-a-door ® s & panelpro instruction manual setting the transmitter to operate pet (pedestrian) mode the pet mode position (see programming the opener) must set prior to coding a transmitter. A. Press the door code button five (5) times - the door code led will illuminate and the courtesy l...
Page 14: Diy
Controll-a-door ® s & panelpro instruction manual 14 b&d doors to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of a b&d garage door opener. B&d doors ...
Page 15
Controll-a-door ® s & panelpro instruction manual 16. Opener safety & security your door can not be used by the opener when: a. There is a locking device installed. B. There is a power failure. Your door can be used when: a. There is an emergency, by disengaging the opener. B. There is a power failu...
Page 16
Controll-a-door ® s & panelpro instruction manual 16 19. Door status indicators door status indicators open led (green) close led (red) beeper open on close on opening flashing closing flashing door travel stopped flashing flashing door obstructed when opening flashing beeps while door is moving doo...
Page 17
17 controll-a-door ® s & panelpro instruction manual 20. Specifications technical specifications controll-a-door ® s panelpro ® power supply 230v - 240va.C. 50hz 230v - 240va.C. 50hz maximum door opening width: height: door area: weight: door must be well balanced and able to be operated by hand, as...
Page 18
Controll-a-door ® s & panelpro instruction manual 18 21. Troubleshooting symptom possible cause remedy the opener does not work from the transmitter garage door in poor condition e.G. Springs may be broken the opener does not have power the battery in the transmitter is flat transmitter does not con...
Page 19
19 controll-a-door ® s & panelpro instruction manual 21 troubleshooting if you need a service call if the opener needs a service please call the dealer who installed the garage door opener (their contact details are usually on a sticker on the back of your garage door). For product assistance contac...
Page 20
Controll-a-door ® s & panelpro instruction manual 20 22. Maintenance door maintenance a poorly maintained door could cause fatal / serious injuries or damage to property. • frequently examine the door, particularly the cables, springs and mountings for signs of wear, damage or imbalance. Do not use ...
Page 21
21 controll-a-door ® s & panelpro instruction manual 25. Service schedule b&d doors is a division of b&d australia pty ltd phone: 13 62 63 website: www.Bnd.Com.Au year / approx. Cycles date details 1 / 3,000 2 / 6,000 3 / 9,000 4 / 12,000 5 / 15,000 service indicator (only available with cad s) whil...
Page 22
Controll-a-door ® s & panelpro instruction manual 22 product: controll-a-door ® s and panelpro ® purchased from:______________________________purchaser:___________________________________ (described as “you” below) address:_____________________________________installed by:___________________________...
Page 23
23 controll-a-door ® s & panelpro instruction manual 27. Optional accessories there are a range of additional accessories for your added convenience and security. Contact your dealer for installation of these accessory items. • safety beams - provides additional protection if the door is closing ont...
Page 24
Controll-a-door ® s & panelpro instruction manual 20 b&d doors is a division of b&d australia pty ltd abn 25 010 473 971 is your opener beeping or flashing? It may be time for a service (for more details see section 22) for a service, contact your dealer using the details below... Dealer: © copyrigh...