- DL manuals
- B&D
- Remote Control
- Controll-A-Door P
- Instruction Manual
B&D Controll-A-Door P Instruction Manual
Summary of Controll-A-Door P
Page 1
Www.Bnd.Com.Au controll-a-door ® p n1854 instruction manual b&d doors is a division of b&d australia pty ltd abn 25 010 473 971 sectional door opener manufacturer’s part # 79070 (manual).
Page 2: Controll-A-Door
Safety rules 03 default settings and specifications 04 about your b&d opener 05 operating controls 06 kit contents 08 installation 09 knockdown c-rail assembly 09 attaching the c-rail 10 determine door type 11 mounting - track type door 12 mounting - non-track type door 13 mounting door bracket & ar...
Page 3: Safety Rules
Safety rules please read these important safety rules these safety alert symbols indicate a personal safety or property damage instruction exists. Read these instructions carefully. This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated i...
Page 4
Default settings & specifications factory default settings default step minimum maximum maximum motor run time 40 seconds - - - courtesy light time 4 minutes (approx.) - - - obstruction force margin 2 1 0 24 auto-close time 30 seconds - - - technical specifications power supply 230v - 240va.C. 50hz ...
Page 5: About Your B&d Opener
Thank you for choosing a controll-a-door ® p automatic garage door opener, designed and developed in australia by b&d doors & openers. The technically advanced construction of this b&d opener ensures you enjoy the following benefits: warranty five (5) year/10,000 cycles full parts and labour warrant...
Page 6: Operating Controls
Operating controls 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 13. Prog input is used to connect the universal handheld programmer to edit control and receiver functions. Safety infra-red beam auto-close shunt has to be placed on to enable the auto-close feature. Terminal block: pwr is used to p...
Page 7
Fig. 01 06 09 07 08 10 11 12 13 04 05 01 02 03 diamond pd power drive : instruction manual © copyright january 2008 b&d doors 7 controll-a-door ® p instruction manual.
Page 8: Kit Contents
Kit contents powerhead unit 1 x controll-a-door ® p powerhead (fig. 02) 1 x transmitter pack (fig. 02) (pack includes two keyring transmitters and batteries) 1 x wall mount transmitter with battery 2 x door attachment arms (fig. 02) 1 x accessory and hardware pack (fig. 02) 1 x installation manual 1...
Page 9: Knockdown C-Rail Assembly
Knockdown c-rail assembly to assemble unpack and assemble the c-rail using the steps outlined below in (fig. 05) . Fig. 05 tension 13mm hex bolt diamond pd power drive : instruction manual © copyright january 2008 b&d doors 9 controll-a-door ® p instruction manual.
Page 10: Attaching The C-Rail
Attaching the c-rail locate shaft into sprocket shaft trac k b rac ket (x2 ) fig. 07 fig. 06 marker door shuttle important note: do not power up the powerhead before assembling to the c-rail. Step 1 - centre the shuttle make sure the shuttle is near the marker, which is located in the centre of c-ra...
Page 11: Determine The Door Type
Determine the door type important note: ensure that no parts of the door extend over public footpaths or roads before installing the opener step 4 - determine door type determine which type of garage door you have as illustrated in (fig. 09) to (fig. 11). For a sectional (panel) door on tracks (fig....
Page 12
Mounting on a track type door fig. 12 track door track level level door drilled holes structural member fig. 14 fig. 13 fig. 15 step 5 - determine bracket position open the door and find the highest point of travel of the top door panel. Using a level, transfer this height to the wall above the door...
Page 13
Fig. 16 mounting on a non-track type door highest point of door travel 25mm door step ladder c-rail step ladder highest point of door travel 25mm door step ladder c-rail step ladder centre of door fig. 19 fig. 18 fig. 17 warning: make sure concrete, brick wall or timber lintels are solid and sound s...
Page 14
Mounting door bracket and arms step 12.1 - alternative mounting option the opener can be fastened to the roof by driving a bolt through the c-rail into a structural timber support. The bolt head’s height must not exceed 6mm (fig. 20) . Step 13 - mounting door bracket the door bracket comes in two pa...
Page 15: Setting Travel Limits
Setting travel limits note: the operate button will not function until the open and close limit positions are set. Note: if a safety infra-red beam is to be used it must be installed before setting the travel limits. Step 15.1 - set the datum position remove the controls cover to access the control ...
Page 16: Setting Travel Limits
Fig. 27 step 15.3 - set the open limit position press and hold the plus (+) button until the door reaches the desired open limit position. Single presses of the button will inch the door closed (fig. 27) . Important warning: the door will automatically close, open and close again once step 15.3(b) i...
Page 17
Please take care when testing the safety obstruction force. Excessive force may cause serious personal injury and/or property damage can result from failure to follow this warning. Step 16.1 - testing close cycle press the operate button to open the door (fig. 28) . Place a piece of timber approxima...
Page 18
Fig. 31 fig. 30 fig. 32 adjusting safety obstruction force adjusting safety obstruction force the safety obstruction force is calculated automatically and set in the memory on the opener during setup. It is usually not necessary to adjust the safety obstruction force. The only time the force may nee...
Page 19: Coding Transmitters
Coding transmitters step 17.1 - storing the transmitter code the opener can only operate from transmitters that have been programmed into its receiver. The receiver needs to learn the codes of any transmitter that will be used with the operator. Up to fourteen (14) codes can be stored in the receive...
Page 20: Coding Transmitters
Step 17.3 - setting the transmitter to operate vacation mode the opener can be programmed into a “vacation mode” where the opener will not respond to any transmitter except one preprogrammed unit. Press code set button three times. The code set led will illuminate and the courtesy light will flash s...
Page 21: Coding Transmitters
Step 17.5 - setting the transmitter to operate pet (pedestrian) mode the opener can be programmed into a “pet mode” where the door opens partially to allow pets to enter/exit the garage: press the code set button five times, the code set led will illuminate and the courtesy light will flash quickly ...
Page 22: Accessories
Accessories terminal block a variety of wired accessory items can be connected to the terminal block such as safety infra-red beams, wall switch, door status indicator and more. The terminal block also features and auxiliary output for controlling other devices from your transmitter. These can inclu...
Page 23: Accessories
Accessories pwr a ux osc com i r (0v) i r black yellow red black yellow red black red black 30v pwr p.E p.E 0v gnd operate aux output fig. 41 fig. 42 safety infra-red beam (part no 062734) for additional protection b&d doors strongly recommend the fitting of a safety infra-red beam. In most countrie...
Page 24: How to Use Your Opener
Fig. 43 how to use your opener for maximum efficiency of your opener, your garage door must be in good operating condition. An annual service of your garage door by an approved dealer is recommended. Cauton - activate the opener only when the door is in full view, free of obstructions and with the o...
Page 25: How to Use Your Opener
How to use your opener manual door operation caution: do not open manual release in the open position, only use in the closed position. Operating the manual release while the door is open, the door may fall rapidly due to weak or broken springs, or due to being improperly balanced. Caution! Do not d...
Page 26: Troubleshooting Guide
If you need a service call if the opener needs service please call the dealer who installed the garage door opener (for product assistance contact 13 62 63 within australia). Before calling you should have the following information to assist in providing the appropriate service: has anything happene...
Page 27: Parameters
Parameters door status indicators door opener state open led (green) close led (red) beeper open on close on opening flashing closing flashing door travel stopped flashing flashing door obstructed when opening flashing door obstructed when closing flashing beeps while door is moving opener overloade...
Page 28: Maintenance
Maintenance maintenance the service led will indicate the requirement for a service and/or adjustment. To reset the service led when the door is serviced, reprogram the door travel limits and the door travel force – on completion of this programming the service led will go out. Whilst your opener do...
Page 29: Spare Parts
Spare parts diamond pd power drive : instruction manual © copyright january 2008 b&d doors 29 controll-a-door ® p instruction manual.
Page 30: Warranty
Warranty 1. Definitions ‘b&d’ means (a) in australia - b&d doors of 17 oasis court, clontarf, queensland, 4019, a division of b&d australia pty ltd (abn 25 010 473 971), or (b) in new zealand - b&d doors nz ltd of 70 allens road east tamaki auckland, which is a subsidiary of b&d australia pty ltd. ‘...
Page 31: Warranty
9. Subject to paragraph 12 hereof; (i) the obligations of b&d under this warranty are limited to those contained herein and such warranties are expressly in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose and not...
Page 32: Www.Bnd.Com.Au
Www.Bnd.Com.Au ©copyright january 2008 b&d doors. All rights reserved. ® and tm are registered trademarks of b&d australia pty ltd. In an ongoing commitment to product quality b&d doors reserve the right to change specifications without notice. E&oe. Qld office: 17 oasis court, clontarf 4019. Ph: (0...