1. DL manuals
  2. B&D
  3. Garage Door Opener
  4. Controll-A-Door ShedMaster
  5. Installation Instructions Manual

B&D Controll-A-Door ShedMaster Installation Instructions Manual

Manual is about: Shed Master AUTOMATIC ROLLING GARAGE DOOR OPENER

Summary of Controll-A-Door ShedMaster

  • Page 1

    Owners copy installation instructions warning it is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instr...

  • Page 2: Table Of Contents

    Table of contents important safety instructions................................... Features.................................................................... Operating controls...................................................... Package contents......................................................

  • Page 3

    Important safety instructions 3 for additional safety protection we strongly recommend the fitting of a photo electric beam. In most countries photo electric beams are mandatory on all garage doors fitted with automatic openers. For a small additional outlay we recommend that photo electric beams be...

  • Page 4: Features

    4 features operation to open or close the door simply press the hand held transmitter or the wall mounted transmitter for two seconds during an open or close cycle the door can be stopped by pressing the button while the door is in motion. The next actuation will move the door in the opposite direct...

  • Page 5: Operating Controls

    5 operating controls p. E. Shunt. The shunt has to be removed when connecting a photo electric beam. Note: p.E. Shunt must not be removed otherwise the opener will not function correctly. Remove only when a p.E beam is to be connected. Status led (yellow) indicates when the datum adjustment screw ha...

  • Page 6: Operating Controls

    Operating controls 6 2 4 v a c s u p p l y p r o g p .E m o t o r 1) p.E. Beam input 2) door status led (yellow) 3) datum adjust screw 4) door code button (black) 5) coding led (red) 6) set button (orange) 7) operate button (blue) 8) force margin set button 9) plus button (for limits setting & force...

  • Page 7: Package Contents

    Package contents 7 item quantity 1 2 rs with visor clips e t t i m s n a r t d l e h d n a h 1 r a b t h g i e w pan head screw m4x50mm 2 2 4 m t u n x e h k c o l i n flat washer i.D 3/16 x 1/2 2 2 s r e v o c r a b g n i k c o l 1 l a u n a m n o i t a l l a t s n i ©copyright 2006 b&d doors trans...

  • Page 8: Before Installation

    Before installation 8 important safety instructions for installation warning: incorrect installation can lead to severe injury. Follow all installation instructions. Side room requirements fig. 1 shows the minimum and recommended side room that is required to mount the opener. The distance between t...

  • Page 9: Mounting The Opener

    Mounting the opener 9 4. Fixing drive unit to the door the drive assembly can be fixed to the rolling garage door in a variety of ways. Described below is one method of fixing. Make sure there is enough side room to slide the drive assembly onto shaft. Please note: the instructions for fixing the dr...

  • Page 10: Mounting The Opener

    Mounting the opener 10 5. Fixing of door curtain to drum wheel the door curtain has to be secured to the drum wheel with suitable fasteners. 1. With the door in the fully closed position, mark the curtain (fig. 7) on both ends of the door. 2. Open door slightly to have access to the marked positions...

  • Page 11: Setting Limits

    Setting limits 11 6.2 setting travel limits note: the opener is factory preset for installation on the right hand side. When the opener is mounted on the left side of the door the opener will travel in reverse. 1. Press minus (-) button, the door will start closing. If the door starts to open - pres...

  • Page 12

    Setting safety obstruction force 12 8. Safety obstruction test please take care when testing the safety obstruction force. Due to excessive forces failure to follow this warning may cause serious personal injury and/or property damage. The test below should be repeated at regular intervals (approxim...

  • Page 13: Coding Transmitters

    Coding transmitters 13 9. Setting transmitter codes make sure to insert the battery into the transmitter. The memory in the openers receiver can store up to six unique remote control transmitters, one dipswitch transmitter and one entry keypad. 9.1 code setting the receiver with smart code or dip sw...

  • Page 14

    Pe beam and final set up 14 13. Fitting the safety photo electric beam sensor (optional) locate the photo electric beam (p.E.) normally closed contact type in a strategic location within doorway. We recommend 150mm above the floor level and as close as possible to the door opening, inside the garage...

  • Page 15: Parameters

    Parameters 15 door status indicators door opener state open led green close led red door status led yellow beeper open on close on opening flashing closing flashing door travel stopped flashing flashing door obstructed when opening flashing door obstructed when closing flashing beeps while door is m...

  • Page 16: Technical Specifications

    Technical specifications input voltage: 230v - 240v ac 50hz controller voltage: 24v dc standby power: 2.8 watts motor power: 100 watts motor type: 24v dc permanent magnet operating temperature: +5° to +40°c maximum door opening: 1,2 width: 5500mm height: 2700mm weight: 100kg rated load: 450n (45kg) ...

  • Page 17: Trouble Shooting

    Trouble shooting 17 *please note: some areas may be prone to excessive radio interference brought on by devices such as cordless telephones, wireless stereo headphones and baby monitors. It is possible that these devices could cause a degree of interference such as to greatly reduce the range of the...

  • Page 18: Spare Parts List

    Spare parts list 18 ©copyright 2006 b&d doors item no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23a 23b 24 25 26 27 28 29 description drive chassis sub-assy interna l gear axle hex serr ation head screw m6x20 interna l gear 62080 clam p w asher 62071 re taining ring stw 45 62073 clam...

  • Page 19

    Warranty and exclusion of liability 1. Definitions ‘b&d’ means (a) in australia – b&d doors of 17 oasis court, clontarf qld 4019, a division of b&d australia pty ltd (abn 25 010 473 971), or (b) in new zealand – b&d doors nz ltd of 70 allens road east tamaki auckland, which is a subsidiary of b&d au...

  • Page 20

    For product support within australia contact 1800 636 407 for product support within new zealand contact 0800 427 236 qld office: 17 oasis court, clontarf 4019 ph: (07) 3883 0200 nsw office: 34-36 marigold street, revesby 2212 ph: (02) 9722 5555 vic/tas office: 147-153 canterbury road, kilsyth 3137 ...