B.E.G. LUXOMAT PD2-M-DALI/DSI-SM Installation And Operating Instruction
Installation and Operating Instruction for B.E.G.-Occupancy detectors PD2-M-DALI/DSI-SM/-FC and PD4-M-DALI/DSI-SM/-FC
2a. Installation of the LUXOMAT
®
PD2/
PD4-M-DALI/DSI-
SM
2b. Installation of the LUXOMAT
®
PD2/PD4-M-DALI/DSI-FC
LUXOMAT
®
PD2/PD4-M-DALI/DSI
1b. Mounting preparations
Work on the 230 V mains supply
may only be carried out by quali-
fied professionals or by instructed
persons under the direction and
supervision of qualified skilled elec-
trical personnel in accordance with
electrotechnical regulations.
Disconnect supply before installing!
When in Master/Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
1a. Features
* For connection of up to 50 lamps
* Suitable for dimmable electronic
ballasts and control modules
* DALI/DSI output
* Constant light control
* Manual switching/dimming
* Semi or full automatic operation
* Luminance (brightness) set point,
switch-off delay time for LIGHT/HVAC
and orientation-light adjustable
* Sensor and power sections in one
housing
* Remote controllable
GB
C
D
68 mm
A circular opening of diameter 68 mm
must be produced in the ceiling. Having
connected up the cables in accor dance
with regulations, the detector is inserted
into the opening as shown in the drawing
opposite and fixed into position with the
assistance of the spring clips.
The detector must be in stalled on a solid and level surface.
The circular cover ring must be removed prior to assembly.
To do this, twist the lens (C) of the PD4 or (D) of the PD2
anticlockwise through approximately 5° and lift off.
Having connected up the wires in accordance with regula-
tions, secure the detector with 2 screws. After installation
replace the lens and lock (turn clockwise). Mains to be
connected.
close open
5. Putting into operation / Settings
Follow-up time for light control
The time can be set infinitely variably at between 1 and 30 minutes.
Symbol TEST: Test mode (Every movement switches on the light for a period
of 1 second, switching it off for a period of 2 seconds after that regardless
of the level of brightness)
Twilight-switch for light control (relay 1)
The switch-on value for the light can be set at between 10 and 2000 Lux.
Using the rotary control, the luminance set points can be set as desired.
Symbol : Night-time operation | Symbol
: Daytime/Night-time operation
Orientation lighting (fixed to 20%)
The orientation lighting can be set infinitely variably at between 5 and 60
minutes resp. “ON” for permanent orientation lighting or “OFF” for no
orientation lighting.
Pulse spacing PD-Slave
2 or 9 seconds can be set for the pause between 2 pulses sent to the
master. The setting can be made with activated ( ) or deactivated ( )
LED indicator.
For devices with a separate slave input, 2 sec. can be set.
6. Settings carried out using remote control (optional)
Remote control LUXOMAT
®
IR-PD-DALI
1. Check Battery:
open battery compartment by pressing the
plastic springs together and removing the
battery-holder.
2. IMPORTANT
Please pay attention, that the setting is Potentio-
meter 1 at “TEST” and Potentiometer 2 not at
“SUN”. All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position “TEST/
SUN”. Please switch Potentiometer 2 over to
“MOON” or any other value.
Caution:
Settings with remote control override the
potentiometer settings.
The product enters an initial
60-second self-test cycle, when
the supply is first connected.
The occupancy detector is
ready for operation. (red Led
flashes)
4. Self test cycle
9s
2s
LED ON
LED OFF
DIP 1 = without function
DIP 2 = without function
DIP 3 = without function
3a. Position DIP-Switches, LEDs and Potentiometer SM
ON
OFF
DIP
1
I
I
I
II
II
III
III
2
II
3
III
3b. Position DIP-Switches, LEDs and Potentiometer FC
PD2-
False ceiling
mounting
PD4-
False ceiling
mounting
PD2-
Surface
mounting
PD4-
Surface
mounting
Potentiometer A Lux Channel 1
Potentiometer B Time Channel 1
Potentiometer C Orientation lighting
LED I green
LED II red
LED III white
The DIP switch settings are
overriden
using the
remote control.
C
C
B
B
A
A
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
1
1
2
2
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
LUX
40
2000
600
1200
200
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
III II I
ON
OFF
DIP
Light
measurement
Light
measurement
1
2
3
Light
measurement
C
C
B
B
A
A
Attention: The light sensor should be mounted
on the opposite side of the window.