- DL manuals
- B&K
- Amplifier
- ST3030 Series II
- Owner's Manual
B&K ST3030 Series II Owner's Manual
Summary of ST3030 Series II
Page 1
B & k components ltd. P/n 12691.
Page 2
B&k components, ltd., 2100 old union road, buffalo, new york 14227.
Page 3
Page 1 safety precautions page 2 purpose and function page 3 design and construction page 3 features page 3 rear panel view page 4 rear panel description page 4 - 5 control muting page 5 - 6 level controls page 6 outputs page 7 inputs page 7 - 8 system installation page 9 making the connection page ...
Page 4
Page 2 warning: to prevent fire or shock hazard, do not expose this unit to rain or moisture. The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient mag...
Page 5
Page 3 the st3030 series ii is a compact, very efficient, two channel power amplifier. It is designed to be used in all types of audio or audio/video systems. The st3030 series ii utilizes high quality electronic circuitry to achieve an environment wherein a detailed, transparent, and highly musical...
Page 6
Page 4 1. Ac fuse holder 5. Rca inputs (unbalanced) 2. Ac input receptacle 6. Level controls ** 3. Speaker outputs 7. Amplifier control muting input/output 4. Balanced inputs 1. Ac fuse holder - holds the ac line fuse. This fuse is an 8 amp / 250 volt slow blow fuse. Replace with same type and value...
Page 7
Page 5 4. Balanced inputs - for connecting balanced signal patch cables (xlr). Explained further on page 8. 5. Rca inputs - for connecting signal patch cables (interconnects) from the preamplifier to the amplifier to pass signal. 6. Level controls - for adjusting the input level to the amplifier. Ex...
Page 8
Page 6 if the control function is desired, each unit in the system must remain connected at all times and the control must be enabled. To enable the control function, the ctrl enable button must be out for each controllable amplifier in the system. For more information on the amplifiers output statu...
Page 9
Page 7 five way binding posts are provided. One pair for each channel. They are designed to accept a banana-type plug or spade lug connector (shown below) and are color coded for easy identification. The red (+) post should always be connected to the speakers (+) jack. The black (-) post should alwa...
Page 10
Page 8 balanced - xlr type connectors accept line input from the preamplifier’s balanced output connectors. There are two input connectors, one for each channel, that may be used to connect the amplifier to the preamplifier. Balanced cable connector - operation - for balanced operation, ensure the b...
Page 11
Page 9 there will most likely be a number of cables involved in the installation of your home entertainment system. Pre-planning is essential in order to maximize system efficiency. We recommend the following as a means of helping you reach that goal: make a diagram of your proposed system by laying...
Page 12
Page 10 connect the wires from your speakers to the appropriate output on the amplifier. It is absolutely essential that you observe correct polarity in these connections. Double check all connections. Plug the amplifier’s power cord into the ac power source. Turn the amplifier’s power switch ‘on’. ...
Page 13: ** Note
Page 11 problem possible cause possible solution no sound 1. Power cord not plugged in. 1. Reconnect power cord. (‘on’ led not illuminated) 2. Power off at ac source. 2. Check ac switch or fuse. 3. Ac power inlet fuse blown 3. Check for shorts or or faulty. Overloading. 4. Control switch in the wron...
Page 14
Page 12 power rating: 8 ohms 200 watts @ 1 khz 4 ohms 300 watts @ 1 khz frequency response 5 hz - 45 khz input sensitivity 1.4 volts thd (s+n) 0.09 % @ 1 khz input impedance 33.2 k ohms damping factor 180 current (peak to peak) 50 amps slew rate 14 v / ) sec dynamic headroom 1.1 db s/n (a-weighted) ...
Page 15
Page 13 b&k components ltd., referred to herein as b&k, warrants your b&k equipment against all defects in material and workmanship for a period of five years from the date of purchase. This warranty applies only to the original purchaser and only to equipment in normal residential use and service. ...
Page 16
B&k components, ltd. 2100 old union road buffalo, new york 14227 716-656-0023 www.Bkcomp.Com.