Service manual model ble3atw vol. 1.0
1.Construction of covers 1 adjusting gauge 55.4 4.5 5.6 8.5 4.8 6.8 0.8 12.1 height of left needle height of feed dog distance of lower looper tip from right side of right needle (at) distance of upper looper tip from right side of right needle distance of lower looper tip from right side of right n...
2. Adjustment of needle,lower looper , upper looper ,chain lopper & presser foot r55.4 +0.1 height of presser foot height of needle needle plate 12.1 +0.1 0 upper looper adjustment 8.5 adjustment of lower looper and upper looper lower looper adjustment max. 8.5 needle guard adjustment 0.8 +0.3 +0.1 ...
Before adjustment of thread delivery system(atd) in case you can not get the proper stitches, please check the following items before you adjust the thread delivery system. A) is thread positioned between discs? Double check the thread position. B) does spring in the head thread guide catch thread p...
Rear clearance adjustment a front clearance adjustment b shut position shut position 0.4 0.4 open position open position 4 5 6 7 8 0.9mm 0.4mm 4 3 1 2 9 3 1 2 9 8.
3-3 how to replace the timing belt of thread delivery unit (see p6) a) loosen the presser foot joint link fixing screw a( 24 upper screw). B) loosen the thread delivery unit fixing screw . C) remove 2 pcs of the thread delivery unit fixing screw . D) push the thread delivery unit downward and remove...
6 15 5 4 12 3 16 10 11 14 1 2 29 30 23 24 25 27 28 26 9 13 21 22 19 18 17 20 6 7 8 a.
3-6 replacement of sensor cable (see p.8) needle thread and looper thread sensor cable consists of 113 pcs of fine stainless wire and its pulling strength is 13kg (3 lb.). Therefore, it is almost unnecessary to replace the sensor cable. In case you replace the cable, refer the followings; there are ...
4 5 13 6 16 15 3 2 1 5 7 18 17 5 20 19 23 5 21 24 22 10 9 4 5 12 4 8 11 14 8.
4. Adjustment of stitches fabric : cotton 1-layer thread : 100% polyester spun thread (maxi-lock or metrosene thread) needle : schmetz hax1sp #11/cr machine: 1-needle (right), 3-thread sewing width : 5.0mm (max) length : 3.0mm d.F. : n stitch selector : b 4-1 adjustment of needle thread sensor cable...
Needle thread sensor cable looper thread sensor cable looper thread sensor cable adjusting screw needle thread sensor cable adjusting screw standard position fine tuning screw 10 turn clockwise become loose turn counter-clockwise become tight.
5. Adjustment of needle threader (see p12) before you adjust the needle threader, you are required to exchange the new needles of schmetz hax1sp #14cr as the bent needles or different needles cause the incorrect timing of needle threader. Also, you are required to make sure that needles are position...
12 31 29 30 28 25 23 27 26 24 22 21 20 33 32 35 34 36 6 12 8 4 3 2 1 10 11 9 13 14 15 16 17 19 5 18 7 6 a.
6. Checking threading steel pipe joint (see p .14) a) set the machine for looper threading. B) move the lock button release lever slightly to the right. C) check the connecting point whether the looper threading pipe joint and threading steel pipe is fitted each other properly. 7. Checking pump 7-1 ...
3 5 4 3 9 8 15 12 13 4 17 2 1 6 10 14 11 16 7 14.
5.5 3.0 fixing screw of knife holder fixing screw of knife driving shaft knife driving shaft 0.5mm 8. Cutting width adjustment a) cut 1 layar cotton fabric and make a cutting width 3.7 0.1mm between the eye of needle and the edge of fabric. B) cutting width adjustment loosen fixing screws of knife h...
180 pin chaining tongue holder pin chaining tongue holder chaining tongue holder pin adjusting chaining tongue adjusting chaining tongue screw a b 9. How to replace adjusting chaining tongue a) move the pin to leftward. B) remove chaining tongue holder set with adjusting chaining tongue. C)loosen sc...
10. Trouble shooting 10-1 needle threads are unbalanced ; * is the serger threaded correctly? See quick reference guide * are the threads snapped in the head guide? See instruction book p.12 * is the stitch selector positioned correctly? See quick reference guide * is the looper thread fine-tuning s...