- DL manuals
- Baby Lock
- Sewing Machine
- Ovation
- Accessories Manual
Baby Lock Ovation Accessories Manual
Summary of Ovation
Page 1
22 serger accessory/feet kit instructions www.Babylock.Com tm.
Page 2: Beading Foot
Machine settings stitch type: 3-thread rolled hem stitch selector: d needle: 02 stitch width: m stitch length: 3-4 rolled hem upper knife: engaged “unlocked” differential feed: n-0.6 sewing speed: slow to moderate speed 1. Remove the left needle from the machine. Set machine to narrow rolled hem (re...
Page 3: Belt Loop Binder
Www.Babylock.Com easily create straps, drawstrings, decorative trim, purse handles and of course, belt loops. This binder takes all of the work out of bias strips by folding and pressing them for you. Choose from 3/4” or 1-1/2” sizes. Machine settings stitch type: triple cover stitch c1-c2-c3 wide c...
Page 4: Blindhem Foot
Looking for a quick, easy way to make your hems invisible? This foot was designed specifically for easily stitching a blindhem on the serger. You can also use this foot for quick stitching along fabric edges. Machine settings needle: 02 upper knife: engaged “unlocked” stitch type: 2-thread narrow he...
Page 5: Clear Foot
Use this foot for better visibility when attaching ribbon and lace, or guiding lightweight decorative stitching. The raised guidelines on the foot ensure that you stitch with accuracy. This foot is perfect for decorative construction and the baby lock exclusive wave stitch. Machine settings any stit...
Page 6: Cover/chain Stitch
Use the cover/chain stitch foot for better visibility and easier control for stitching curves or turning tight corners and attaching tape and ribbons. Machine settings: stitch: left, right or center chain stitch, narrow, wide or triple cover stitch. (select one and check with instruction book for le...
Page 7: Curving Foot
The curve foot is short and has a flat sole, making it a good choice for stitching curves and sewing over cross seams. Its short size is also good for sewing around cuffs, necklines and children’s wear using the cover stitches. Machine settings: 1. Raise the presser foot lever. 2. Lower the cutting ...
Page 8: Double Fold Bias
Www.Babylock.Com this conventional binder will double fold and sew bias strips to your project in one quick step, using either a chain or coverstitch. Choose from two widths based on your preference. Machine settings stitch type: 1-1/2” chain stitch - c3 needle position c2-c3 narrow right cover stit...
Page 9: Elastic Foot
Instructions for elastic foot: 1. Before attaching the elastic foot to the machine, loosen the elastic pressure adjustment screw, raise the pressure plate and insert the elastic until it reaches behind the foot (see illustration). Tighten the elastic pressure adjustment screw slightly. Note: the lin...
Page 10: Elastic Foot
Www.Babylock.Com coverstitch: machine settings stitch type: triple cover stitch or wide cover stitch needles: triple cover stitch-c1,c2,c3 wide cover stitch-c1,c3 stitch length: 4 stitch width: m differential feed: normal upper knife: disengaged “locked” sewing table: remove knife cover and snap on ...
Page 11: Lace Applicator Foot
Www.Babylock.Com use this foot for guiding lace onto your fabric with a 2-thread flatlock or to attach ribbon to your fabric under a cover stitch. Or attach decorative trim by combining an overlock stitch with a chain stitch. Follow your “quick reference threading guide” for various stitches and set...
Page 12: Pintuck Foot
Use this foot on your serger to add beautiful texture to a classic heirloom or everyday garment. The groove on this foot allows for perfect spacing with professional results. Achieve precise pintucking when making corded and hollow tucks as well as parallel and curved forms. 1. Change to sewing tabl...
Page 13: Piping/cording Foot
Machine settings stitch type: 4-thread overlock stitch selector: a needle: o1 and o2 stitch width: m -7.5 stitch length: 3-3.5 upper knife: engaged “unlocked” differential feed: n sewing speed: slow to moderate speed to make covered piping: fold bias strip of fabric right side out around the cording...
Page 14: Plain Hemmer Foot
Guide fabric into a perfectly straight hem without any pre- project pressing. The plain hemmer is designed to be used for straight hemming only. Leave one seam of the garment open. After hemming, sew the seam closed. Machine settings stitch type: chain stitch - c1 needle position narrow left cover s...
Page 15: Plain Hemmer Foot
Www.Babylock.Com guide fabric into a perfectly straight hem without any pre- project pressing. The plain hemmer is designed to be used for straight hemming only. Leave one seam of the garment open. After hemming, sew the seam closed. Machine settings stitch type: chain stitch stitch width: m-7.5 nee...
Page 16: Quilt Guide
Www.Babylock.Com instructions: 1. Insert the stem of the quilt bar into the hole at the rear of the presser foot bar. 2. Adjust the stem of the quilt bar so that the guide aligns with the seam that has already been sewn. 3. Tighten the quilt bar fixing screw. 4. Continue to serge so the guide follow...
Page 17: Ruffling Foot
Www.Babylock.Com machine settings stitch type: 4-thread overlock stitch width: m-7.5 needle: 01 and 02 stitch length: 4 upper knife: engaged “unlocked” differential feed: 2 stitch selector: a sewing speed: slow to moderate gathering fabric: place one layer of fabric under the presser foot and sew. G...
Page 18: Single Fold Bias
Single fold bias binder 1-1/8 inch (28mm) (ble8-s4) 1-5/8 inch (40mm) (ble8-s5) instructions this conventional binder will double fold and sew bias strips to your project in one quick step on the serger, using either a chain or cover stitch. Choose from two widths based on your preference. Machine s...
Page 19: Single Downturn
Machine settings stitch type: 1/4” narrow left cover stitch-only c1-c2 stitch type: 5/8” narrow left cover stitch-c1-c2 wide cover stitch-c1-c3 stitch type: 1” wide cover stitch-c1-c3 triple cover stitch c1-c2-c3 narrow left cover stitch c1-c2 sewing speed: moderate to slow stitch length: 3-4 upper ...
Page 20
Www.Babylock.Com item lnis-bles8ftkit.