1. DL manuals
  2. Baby Trend
  3. Car Seat
  4. EuroSport
  5. Owner's Manual

Baby Trend EuroSport Owner's Manual - Warning!

Manual is about: 3-in-1 car seat

Summary of EuroSport

  • Page 1

    Carefully read and understand all instructions and warnings in this manual. Failure to properly use this car seat increases the risk of serious injury or death in a sudden stop or crash. By baby trend www.Babytrend.Com efb55ff0711 keep instructions for future use. Warning! Owner’s manual stage 1 tod...

  • Page 2

    Table of contents 7.3 installation with top tether..................................................28 7.3.1 installation - latch with top tether...............................29 7.3.2 installation - lap/shoulder belt with top tether...............34 7.3.3 installation - lap belt only with top tethe...

  • Page 3

    4 your child’s safety depends on: 1. Choosing the correct use mode for your child’s weight and height. 2. Choosing the best location within your vehicle for installing the car seat. Seating positions with frontal air bags must be avoided if possible. 3. Proper installation. A. Toddler use mode - req...

  • Page 4

    5 failure to follow these instructions and car seat labels can result in child striking the vehicle’s interior during a sudden stop or crash. • use this car seat only with children who weigh between 22 and 100 lbs. (10 and 45 kg.) and whose height is between 29 and 57 in. (74 and 145 cm) and who are...

  • Page 5

    7 • this car seat is designed and tested to accommodate a child of a specific range of weight and height. Using the car seat for a child whose weight or height is outside of these limits will increase the risk of death or serious injury in the event of a crash (see section 5.0 of this manual for wei...

  • Page 6

    3.0 features and benefits 3.1 toddler car seat ( with built-in harness system) 9 harness strap covers toddler shoulder belt guide body insert harness clip toddler shoulder belt guide seat base smart safety buckle armrest cup holder can be mounted on either side of seat base. Harness straps harness a...

  • Page 7

    3.0 features and benefits 3.4 backless booster car seat ( without harness system and back support) 12 seat base pad owner’s manual owner’s manual storage pocket (under pad) cup holder can be mounted on either side of seat base. Seat base armrest armrest shoulder belt positioner assembly (stored in o...

  • Page 8

    4.0 preparing car seat for use 14 backless booster car seat without harness system “40 - 100 lbs.” (18 to 45 kg) (see weight and height recommendations” section). - remove back support (see “assembly and removal of back support” section). 4.3 select a vehicle seating location to install the car seat...

  • Page 9: Warning!

    16 warning! Death or serious injury can occur: •failure to use child restraint in a manner appropriate for your child’s size may increase the risk of serious injury or death. This child restraint is designed for use only by children who are at least 1 year old, can sit upright unassisted, who weigh ...

  • Page 10

    5.0 weight and height recommendations 18 5.3 high-back booster car seat use ( without built-in harness system) child must meet all of the following requirements to use the high-back booster car seat mode: • child’sweightisbetween 30 and 100 lbs. (13.6 and 45 kg) and • child’sheightisbetween 42 and 5...

  • Page 11: Warning!

    19 5.0 weight and height recommendations 5.4 backless booster car seat use ( without built-in harness system) child must meet all of the following requirements to use the backless booster car seat mode: • child’sweightisbetween40 and 100 lbs. (18 and 45 kg) and • child’sheightisbetween42and 57 in. (...

  • Page 12

    21 • please review your vehicle owner’s manual to determine the bestlocationforeachcarseatusemode,anyspecific instructions for car seat installation, or to determine if any locations are unsafe for car seat installation. If you do not have the vehicle owner’s manual or the owner’s manual does not ad...

  • Page 13: Warning!

    6.2 seating locations to avoid do not use this car seat in the following seating locations. • never use this car seat in a vehicle seating location that has an active air bag unless recommended in the vehicle owner’s manual. If your vehicle is equipped with a front passenger air bag, please refer to...

  • Page 14

    7.0 toddler car seat ( with built-in harness) installation and use 25 the belt path routing used to secure this car seat into a vehicle is dependent on installation with or without the top tether. - if the car seat is installed with the top tether, the “front entry” belt routing must be used. - if t...

  • Page 15

    Installation without top tether “rear entry” belt routing the “rear entry” belt routing is used to secure the toddler car seat (with harness) when installed without the top tether. The latch lower anchor belt and vehicle seat belts are routed through the “rear entry” belt path in the same way. “rear...

  • Page 16: Warning!

    29 7.0 toddler car seat ( with built-in harness) installation and use 7.3.1 installation - latch with top tether warning! • only use the car seat latch system in vehicle seating positions designated by the vehicle manufacturer as latch use position and have anchor spacing of 11 inches (280 mm). • th...

  • Page 17

    32 7.0 toddler car seat ( with built-in harness) installation and use 13. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should not move more than 1 inch in either direction. • ifthecarseatmovesmorethan 1 inch, retighten the ...

  • Page 18: Warning!

    34 7.0 toddler car seat ( with built-in harness) installation and use 7.3.2 installation - lap/shoulder belt with top tether warning! • vehicle seat belt system must stay tightly adjusted to car seat at all times. If vehicle seat belt does not stay tight, read vehicle owner’s manual and “vehicle sea...

  • Page 19

    35 6. If the vehicle seat back is adjustable, adjust into the upright position or the positionspecifiedinthevehicleowner’s manual for use with a car seat. 7. Pull the vehicle lap/shoulder belt out and route through the car seat using the “front entry” belt routing as shown in section 7.2 and buckle ...

  • Page 20: Warning!

    37 1. Loosen top tether by pressing the button on the tether adjuster and sliding belt through adjuster . 2. Unhook top tether hook from vehicle tether anchor. Press up on retainer , unhook tether hook , and remove . 3. Unbuckle vehicle seat belt and remove seat belt from belt path. 7.0 toddler car ...

  • Page 21

    7.0 toddler car seat ( with built-in harness) installation and use 40 13. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should not move more than 1 inch in either direction. • ifthecarseatmovesmorethan1inch, retighten the ve...

  • Page 22: Warning!

    7.0 toddler car seat ( with built-in harness) installation and use 42 7.4.1 installation - latch without top tether warning! • only use the car seat latch system in vehicle seating positions designated by the vehicle manufacturer for use with latch and have anchor spacing of 11 inches (280 mm). • th...

  • Page 23

    9. Place knee inside seat and while pressing down, pull on the free end of the latch lower anchor belt to tighten the latch lower anchor belt around the car seat . After tightening the latch belt, the green tension indicator on the latch adjuster must be visible. 10. Check for a secure installation ...

  • Page 24: Warning!

    To remove car seat: 1. Loosen latch lower anchor belt by putting knee in seat and while pressing down , lift up on latch adjuster and slide belt through adjuster . 2. Unhook latch lower anchor belt connectors from vehicle anchors. Press up on retainer , unhook latch connector , and remove . Note: wh...

  • Page 25

    7.0 toddler car seat ( with built-in harness) installation and use 48 10. While holding the lap belt tight, pull slack out of shoulder belt and allow retractor to tighten shoulder belt. 11. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. T...

  • Page 26: Warning!

    7.0 toddler car seat ( with built-in harness) installation and use 50 4. Place the car seat on the vehicle seat in a seating location and centered between the lap belt anchorages (see “selecting a vehicle seating location” section). 5. If the vehicle seat back is adjustable, adjust into the upright ...

  • Page 27

    51 7.0 toddler car seat ( with built-in harness) installation and use 9. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should not move more than 1 inch in either direction. • ifthecarseatmovesmorethan 1 inch, retighten the l...

  • Page 28: Warning!

    53 7.0 toddler car seat ( with built-in harness) installation and use warning! Death or serious injury can occur: • failure to properly adjust the harness on your child increases the risk of death or serious injury in the event of a sudden stop or crash. Follow the instructions very closely to ensur...

  • Page 29

    7.0 toddler car seat ( with built-in harness) installation and use 56 5. Close harness clip and position as close to arm pit level as possible. 6. Check that the harness straps are snugly adjusted. - check that harness straps are snug on child’s shoulders and thighs. - the harness strap is properly ...

  • Page 30: Warning!

    57 to remove your child: 1. Unbuckle harness clip – press on the tabs in the top and bottom of the harness clip and pull apart to open the harness clip. 2. Unbuckle the smart safety buckle to open the harness system note: each time the smart safety buckle is unbuckled, the safety alarm on the buckle...

  • Page 31: Warning!

    59 8.0 booster car seat ( without built-in harness) installation and use warning! Death or serious injury can occur: • if child will not keep vehicle shoulder belt properly positioned on shoulder, do not use this booster car seat. Use a different child restraint system. • do not allow child to slide...

  • Page 32

    62 8.0 booster car seat ( without built-in harness) installation and use 8. Adjust head support so that the vehicle shoulder belt passes over the shoulder midway between the neck and the end of the shoulder. The booster shoulder belt guide in the head support should be just above the child’s shoulde...

  • Page 33: Warning!

    Death or serious injury can occur: • child must be at least 4 years old and weigh at least 40 lbs. (18 kg) to use the backless booster car seat. • use high-back booster mode as long as possible. The back support and head support provide incremental crash protection in frontal and side impact crashes...

  • Page 34: Warning!

    65 8.0 booster car seat ( without built-in harness) installation and use to secure car seat and your child: 1. Assemble vehicle shoulder belt positioner to back of car seat (see “assembly and removal of vehicle shoulder belt positioner” section). 2. Place the car seat on the vehicle seat in a seatin...

  • Page 35: Warning!

    68 9.0 vehicle seat belts 9.1 check that the vehicle seat belt is safe to use the car seat is designed to be tightly installed at all times. The vehicle seat belt must be capable of maintaining tight installation at all times. A variety of vehicles have been equipped with vehicle seat belt systems t...

  • Page 36

    Vehicle seat belt systems that are adequate for installation of car seat: the following vehicle seat belt systems can be used with the car seat provided that all of the other requirements prescribed in these instructions, including seat position, and all instructions provided by your vehicle’s owner...

  • Page 37

    71 vehicle seat belt systems that are not safe for installation of car seat: do not use the following types of vehicle seat belt systems with the car seat. These vehicle seat belt systems will not hold the car seat securely in place at all times. The addition of a locking clip will not make these ve...

  • Page 38

    9.0 vehicle seat belts 74 if you have any of the above vehicle seat belt systems, do not use it to secure the car seat in the vehicle. Look in the vehicle for a location that has a more suitable vehicle seat belt system as described in the “vehicle seat belt systems that are adequate for installatio...

  • Page 39: Warning!

    75 10.0 operation and adjustments 10.1 assembly and removal of back support before using your car seat in your vehicle, you must assemble the back support and prepare the car seat harness straps for your child. To assemble back support: • placecarseatonthefloororother firmsurfaceandloosentheharness ...

  • Page 40: Warning!

    10.0 operation and adjustments 77 3. Check that the harness straps are snugly adjusted. The harness strap is properly tightened if you are not able to insert more thanonefingerbetweentheharnessstrap and the child’s shoulder or thigh and green tension indicators are visible on both harness adjusters....

  • Page 41

    10.0 operation and adjustments 79 the harness can be adjusted to three different heights. The proper height of the harness straps is at or just above your child’s shoulders. If your child’s shoulders are between two levels, always use the higher of the two. Remove the body insert if your child’s sho...

  • Page 42

    10.0 operation and adjustments 81 10.4 harness removal and assembly harness removal: a. Buckle harness and chest clip to hold harness system together. B. Adjust the harness to loosen harness straps. C. From the front of back support, slide top corners of back support pad off back support exposing ha...

  • Page 43: Warning!

    10.0 operation and adjustments 83 harness assembly: warning! • harness straps must be at or above the child’s shoulders. Failure to properly adjust the harness on your child increases the risk of death or serious injury in the event of a sudden stop or crash. • harness strap covers must always be us...

  • Page 44

    10.0 operation and adjustments 86 10.5 adjusting the head support the head support on this car seat is designed to provide maximum lateral head protection. Never remove the head support from the back support. The head support can be moved up or down through a series of positions. To adjust head supp...

  • Page 45

    10.7 cup holder attachment a cup holder is provided and can be attached to either one of the armrests. Use of cup holder is optional. •locate slot in the outer side of the armrest pad and expose the cup holder attachment track. • align the cup holder slot with the cup holder attachment track and sli...

  • Page 46

    89 11.1 certifications this car seat conforms to all federal motor vehicle safety standards for use in motor vehicles and aircraft. See use modes below: toddler car seat mode ( with harness system): this restraint is certifiedforuseinmotorvehiclesandaircraft. Booster car seat mode ( without harness ...

  • Page 47: Warning!

    12.0 cleaning and maintenance 92 to remove seat base pad: • removeharnessandcrotchstrap(see“harnessremovaland assembly” section. • slidethebaseseatpadoverthearmrestsandoffthefrontof the car seat. Reverse above steps for replacing pads and harness system. Cleaning harness system: • surfacewashonlywit...

  • Page 48

    13.0 replacement parts 93 13.0 replacement parts if you need help or replacement parts, please call our customer service department at 1-800-328-7363 between the hours of 8:00amand4:30pm,pacificstandardtime,mondaythrough friday or visit us online at www.Babytrend.Com. 14.0 register your car seat 94 ...