1. DL manuals
  2. Bachmann
  3. Toy
  4. E-Z TRACK
  5. Assembly Manual

Bachmann E-Z TRACK Assembly Manual

Summary of E-Z TRACK

  • Page 1

    Attention–produit fonctionnant À l’ÉlectricitÉ non recommandÉ pour les enfants de moins de 14 ans. Comme pourtousles produitsÉlectriques,manipuleretutiliser avec prÉcaution afin d’Éviter tout risque de choc Électrique. EntrÉe : 120 vca 60 hz. Sortie : ca 16 v 1000 ma. Caution-electrically operated p...

  • Page 2

    2 in the event of damaged or defective components, do not return this train set to the store where it was purchased. Please review the assembly and operating instructions listed on this sheet and the warranty included with this set. If service is required, contact the bachmann service department at ...

  • Page 3

    Important notice: to ensure trouble-free operation, use only bachmann’s patented e-z track ® products with this set. Use of non-compatible systems may result in unsatisfactory performance. Note to parents: it is recommended that this set be periodically examined for potential hazards and that any po...

  • Page 4

    1 4 proper e-z track ® assembly great care must be given to assembling track sections! Improper assembly will cause derailments and/or interrupted electrical contact. When assembling the track, snap it together tightly (figure 1), and at the same time , make sure the rail and rail joiners are seated...

  • Page 5

    Be sure rail joiners do not slip under the rails without properly connecting. Assurez-vous que les raccords ne glissent pas sous les rails sans les relier correctement. 2 asegúrese que las juntas del riel no se deslicen debajo de los rieles sin conectarse correctamente. Read before use attention to ...

  • Page 6

    6 5 7 8 4 6 connecting track power do not plug in the speed controller yet. Turn the speed controller to the “off” position (figure 4 ). Plug the red terminal wire into the “output to track” jack of the speed controller as shown in figure 5 . Connect the other end of the red terminal wire to the ter...

  • Page 7

    12 11 10 7 operation plug power pack into wall outlet (figure 9 ). Begin feeding power to the track by slowly turning the control knob clockwise (figure 10 ). The direction in which the locomotive travels is determined by the direction switch located at the top of the controller (figure 11). To chan...

  • Page 8

    8 action checklist if your train doesn’t run or stops running if your train doesn’t run, check the following: 1. Make sure the power pack is plugged into a live wall receptacle. 2. Make sure all locomotive and car wheels are on the track. 3. Check to make sure all wiring is secure. 4. Check to make ...

  • Page 9

    13 9 short circuits if your train stops or fails to start, a short circuit may be indicated. Unplug the power pack at once . Derailed wheels may cause a short, so check to make sure all wheels are properly on the track. Check all connections and be sure that no metal of any sort is across the rails ...

  • Page 10

    10 lubrication after every 24 hours of operation, your train set requires light lubrication to keep it in top operating condition. Do not use common household lubricants, as they may damage your train . Contact your local hobby retailer for proper lubrication products and procedures. Lubrification a...

  • Page 11

    11 cleaning and maintenance care must be taken to clean and maintain your train for optimum performance. Clean track and clean wheels ensure good electrical contact for proper train operation. After every eight hours of use, wipe the track rails and exposed portions of your locomotive’s wheels with ...

  • Page 12

    12 bachmann industries, inc. 1400easterieavenue,philadelphia,pa19124usa www.Bachmanntrains.Com printedinchina bachmann industries, inc. 1400easterieavenue,philadelphie,pa19124É.-u. Www.Bachmanntrains.Com imprimé en chine bachmann industries, inc. 1400easterieavenue,philadelphia,pa19124e.E.U.U. Www.B...