- DL manuals
- Backyard Discovery
- Play Sets & Playground Equipment
- 1605022
- Owner's Manual
Backyard Discovery 1605022 Owner's Manual
Summary of 1605022
Page 1
Made in china features the fastening system. Save this assembly manual for future reference in the event that you need to order replacement parts. • owner's manual • frequently asked questions • assembly instructions • warranty information beach front wooden play set mo del: 1605022.
Page 2
General safety instructions purpose this product is intended for outdoor, domestic use only. It is not suitable for commercial or medical use. Danger for children warning! No eating while using the product this product may only be used with adult supervision at all times. The packaging material is n...
Page 3: Safety Instructions
In certain areas during winter, snow buildup and the low temperatures can damage the product. It is recommended to remove snow buildup and to store the product indoor. We strongly recommend visual inspections every 3 months to insure the integrity of the entire product. Replace any parts as necessar...
Page 4
Consumer information sheet for playground surfacing materials the us consumer product safety commission (cpsc) estimates that about 100 000 playground equipment- related injuries resulting from falls to the ground surface are treated annually in us hospital emergency rooms. Injuries involving this h...
Page 5
Play set assembly manual faqs: 1. Does the area for the playset need to be level? Yes. We recommend the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What age range is appropriate for the playset...
Page 6
Tools required for installation: (these are the tools that are generally required for assembly of our swing sets. These tools are not included in the swing set purchase.) (level 24") (open end wrenches 1/2") (square) (tape measure) (3/8" drive ratchet, 1/2" std sockets 1/2" deep sockets) (claw hamme...
Page 7: Important Assembly Notes
Important assembly notes 1) while assembling unit, take time before and after each phase to make sure fort is level. If fort is not level, assembly will be difficult and improper assembly may result. Extra care must be taken to ensure the fort is square. 2) tighten bolts securely, tighten nuts on bo...
Page 8: Parts Identification
Parts identification wood components (not to scale) m77 - slide brace - w100544 5/8"x3 3/8"x17 1/4" (16x86x438) (1) m78 - center slide brace - w100545 5/8"x3 3/8"x17 1/4" (16x86x438) (2) e4 - upright - w2a01970 1 3/8"x3 3/8"x57 3/8" (36x86x2274) (1) q2 - sandbox seat support - w4l06434 1"x4 3/8"x8" ...
Page 9: Parts Identification
Parts identification wood components (not to scale) k4 - ground board - w4l06899 5/8"x5 1/4"x61" (16x134x1549) (1) k6 - ground board - w4l06904 5/8"x5 1/4"x44 1/2" (16x134x1129) (1) k5 - serving shelf - w4l06902 5/8"x5 1/4"x40 7/8" (16x134x1038) (1) j6 - ladder rail - w4l06910 1"x2 3/8"x50 1/8" (24x...
Page 10: Parts Identification
Parts identification wood components (not to scale) y2 - floor board - w4l06917 5/8"x4"x40 3/8" (16x102x1024) (1) m6 - floor board - w4l06918 5/8"x3 3/8"x45 1/8" (16x86x1145) (10) m7 - wall rail - w4l06919 5/8"x3 3/8"x41 1/2" (16x86x1054) (2) m8 - wall rail - w4l06920 5/8"x3 3/8"x42 1/8" (16x86x1070...
Page 11: Parts Identification
Parts identification wood components (not to scale) y3 - sunburst half moon - w4l06954 5/8"x4"x12" (16x102x306) (2) n3 - sunburst board - w4l06955 5/8"x2 3/8"x11 3/4" (16x60x299) (2) n4 - sunburst board - w4l06956 5/8"x2 3/8"x8 1/8" (16x60x205) (4) o4 - awning board - w4l06957 5/8"x1 3/8"x32 1/4" (1...
Page 12: Parts Identification
Parts identification hardware d - nut barrel wh 5/16x7/8 - h100005 (19) c - nut barrel wh 5/16x1 1/2 - h100006 (2) f - bolt wh 5/16x1 - h100008 (8) g - bolt wh 5/16x1 1/4 - h100009 (2) h - bolt wh 5/16x1 1/2 - h100010 (19) j - bolt wh 5/16x1 3/4 - h100011 (8) k - bolt wh 5/16x2 - h100012 (30) l - bo...
Page 13: Parts Identification
Parts identification hardware an - bolt hex 5/16x2-3/4 - h100047 (4) lc - lag screw wh 1/4x1-1/2 - h100145 (11) ch - screw tapping 14x1-1/2 - h100109 (17) ba - bolt pth 1/4x3/4 - h100063 (13) ks - nut barrel wh 1/4x5/8 - h100136 (2) ky - bolt wh 1/4x1/2 - h100141 (2) cy - screw pwh 8x5/8 - h100128 (...
Page 14: Parts Identification
Parts identification accessories (not to scale) fa - quick link - a100069 (6) gq - l bracket 66x66x127 blue - a100153 (2) - 90° l-bracket - blk - a4m00555 (1) sb - triangle plate blue 100 5 hole - a100309 (2) sq - "a" revision tag - a100314 (1) - swing beam ext. Bracket blue - left - a4m00511 (1) - ...
Page 15: Parts Identification
Parts identification accessories (not to scale) - tarp - a6p00123 43 1/4"x93 1/2" (1100x2374) (1) - awning - a6p00124 1/64"x32 1/4"x22 1/4" (.4x818x566) (1) - slide bed 8' lime - a6p00131 (1) hd - swing seat blue - a6p00133 (2) - lime hc rock #1 - a6p00128 (2) - blue hc rock #2 - a6p00040 (2) - cran...
Page 16
Monkey bar assembly step 1 e7 - monkey bar rail - w4l06938 1 3/8"x3 3/8"x48" (36x86x1219) (1) bolt wh 5/16x1 1/2 (3) t-nut 5/16 (3) sb - triangle plate blue 100 5 hole - a100309 (1) e7 bolt wh 5/16x1 1/2 (3 plcs) triangle plate blue 100 5 hole t-nut 5/16 (3 plcs) washer lock ext 8x19 (1) nut barrel ...
Page 17
E7 e7 - monkey bar rail - w4l06938 1 3/8"x3 3/8"x48" (36x86x1219) (1) sb - triangle plate blue 100 5 hole - a100309 (1) monkey bar assembly step 2 bolt wh 5/16x1 1/2 (3) t-nut 5/16 (3) t-nut 5/16 (3 plcs) bolt wh 5/16x1 1/2 (3 plcs) triangle plate blue 100 5 hole bolt wh 5/16x1 washer lock ext 8x19 ...
Page 18
Monkey bar assembly step 3 e5 - monkey bar upright - w4l06964 1 3/8"x3 3/8"x70 3/8" (36x86x1786) (1) - hand grip lime plastic - a6p00127 (1) t-nut 5/16 (2) bolt wh 5/16x1 1/2 (2) screw tapping 14x1-1/2 (2) washer lock int 8x15 (2) washer flat 9x18 (2) bolt wh 5/16x1 1/2 (2 plcs) t-nut 5/16 (2 plcs) ...
Page 19
Monkey bar assembly step 4 t-nut 5/16 (2) washer lock int 8x15 (2) washer flat 9x18 (2) screw tapping 14x1-1/2 (2) bolt wh 5/16x1 1/2 (2) e5 - monkey bar upright - w4l06964 1 3/8"x3 3/8"x70 3/8" (36x86x1786) (1) - hand grip lime plastic - a6p00127 (1) bolt wh 5/16x1 1/2 (2 plcs) t-nut 5/16 (2 plcs) ...
Page 20
Monkey bar assembly step 5 screw tapping 14x1-1/2 (10) - metal rung 559 blue - a4m00585 (5) screw tapping 14x1-1/2 (10 plcs) metal rung 559 blue (5 plcs).
Page 21
Monkey bar assembly step 6 bolt hex 5/16x2-3/4 (2) lag screw wh 5/16x2 (4) washer lock ext 8x19 (8) washer lock ext 12x19 (4) washer lock int 8x15 (2) washer flat 9x18 (2) t-nut 5/16 (2) nut barrel wh 5/16x7/8 (4) bolt hex 5/16x2-3/4 (2 plcs) washer lock int 8x15 (2 plcs) washer flat 9x18 (2 plcs) w...
Page 22
Bench assembly step 1 h7 h7 h7 - bench ground board - w4l06967 1"x3 3/8"x18 1/8" (24x86x460) (2) fz - l bracket blue 32x51 - a4m00646 (2) nut barrel wh 5/16x7/8 (2) bolt wh 5/16x1/2 (2) washer lock ext 12x19 (2) nut barrel wh 5/16x7/8 (2 plcs) washer lock ext 12x19 (2 plcs) bolt wh 5/16x1/2 (2 plcs)...
Page 23
Bench assembly step 2 screw pfh 8x1 3/4 (8) h8 h8 h8 - bench upright - w4l06968 1"x3 3/8"x11 3/4" (24x86x300) (2) screw pfh 8x1 3/4 (8 plcs).
Page 24
Bench assembly step 3 screw pfh 8x1 3/4 (8) screw pfh 8x1 3/4 (8 plcs) h9 h9 h9 - bench seat support - w4l06969 1"x3 3/8"x6 1/2" (24x86x166) (2) flush to top..
Page 25
Bench assembly step 4 screw pfh 8x1 3/4 (8) m12 m12 m12 - bench seat - w4l06970 5/8"x3 3/8"x26" (16x86x660) (2) screw pfh 8x1 3/4 (8 plcs).
Page 26
Swing beam assembly step 1 bolt hex 5/16x2-3/4 (2) bolt wh 5/16x1 3/4 (3) nut barrel wh 5/16x7/8 (3) washer flat 8x27 (4) nut lock 5/16 (2) sb74 - swing beam extended - w4l06961 2"x5 1/4"x89 1/2" (50x134x2274) (1) - swing beam ext. Bracket blue - left - a4m00511 (1) - swing beam ext bracket blue - r...
Page 27
Swing beam assembly step 2 lag screw wh 5/16x2 (2) bolt wh 5/16x4 1/2 (1) nut barrel wh 5/16x7/8 (3) washer lock ext 12x19 (3) washer lock ext 8x19 (5) e77 - angle brace - w4l06962 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (2) w71 - swing beam support - w4l06963 2"x3 3/8"x49 5/8" (50x86x1260) (1) e77 w71 e...
Page 28
Swing beam assembly step 3 swing beam bracket (step 1) swing beam end (step 2) bolt wh 5/16x2 1/2 (2) bolt wh 5/16x1 3/4 (2) nut barrel wh 5/16x1 1/2 (2) washer lock ext 12x19 (2) nut barrel wh 5/16x7/8 (2) washer lock ext 8x19 (2) bolt wh 5/16x1 3/4 (2 plcs) nut barrel wh 5/16x7/8 (2 plcs) nut barr...
Page 29
Swing beam assembly step 4 washer safety 17x30 (6) nut lock 5/16 (6) washer flat 8x27 (6) 9 1/2" swing hanger quick link (6) nut lock 5/16 (6 plcs) washer flat 8x27 (6 plcs) washer safety 17x30 (6 plcs) 9 1/2" swing hanger quick link (6 plcs).
Page 30
Slide assembly step 1 top bottom tip: prebending the ends will ease assembly. M77 - slide brace - w100544 (1) bolt wh 5/16x1/2 (3) use 'm77' slide brace as a template for drilling bottom hole pattern in slide bed. Be sure to place slide brace up 1/4" from bottom edge of slide bed before marking hole...
Page 31
Slide assembly step 2 tip: a helper is required for this phase. Note: make certain supports and slide bed are fully engaged within channel of slide rails. Screw pfh 8x2 1/2 (24) m78 - center slide brace - w100545 (2) ha - slide rail 8' blue left - a100162 (1) gz - slide rail 8' blue right - a100161 ...
Page 32
Step 1 e2 m8 e3 h1 j1 k4 k3 k3 bolt wh 5/16x2 (10) washer lock ext 8x19 (16) t-nut 5/16 (18) e2 - upright - w4l06891 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (1) e3 - upright - w4l06892 1 3/8"x3 3/8"x89 1/2" (36x86x2274) (1) k3 - ground board - w4l06896 5/8"x5 1/4"x42 1/8" (16x134x1070) (1) h1 - floor rai...
Page 33
Step 2 e4 o3 g1 o3 m8 h10 m1 e1 k3 k1 bolt wh 5/16x2 1/4 (8 plcs) bolt wh 5/16x2 1/4 (8) bolt wh 5/16x2 (12) screw pfh 8x1 3/4 (4) screw pwh 8x5/8 (2) washer lock ext 8x19 (20) t-nut 5/16 (24) washer lock ext 8x19 (20 plcs) t-nut 5/16 (20 plcs) screw pfh 8x1 3/4 (4 plcs) t-nut 5/16 (4 plcs) screw pw...
Page 34
Step 3 k2 k2 k2 k2 lag screw wh 5/16x1 1/2 (16) washer lock ext 8x19 (16) k2 - ground board - w4l06894 5/8"x5 1/4"x43 1/4" (16x134x1097) (4) lag screw wh 5/16x1 1/2 (16 plcs) washer lock ext 8x19 (16 plcs).
Page 35
Step 4 screw pfh 8x1 1/2 (24) g2 q2 q2 g2 q2 q2 g2 - sandbox seat - w4l06433 1"x5 1/4"x14 5/8" (24x134x370) (2) q2 - sandbox seat support - w4l06434 1"x4 3/8"x8" (24x112x202) (4) screw pfh 8x1 1/2 (24 plcs) screw pfh 8x1 3/4 (8) screw pfh 8x1 3/4 (8 plcs) g2 q2 q2 bench sub assembly.
Page 36
Step 5 j1 flush o1 boards to top of j1 board. O1 3 1/16" typical spacing screw pfh 8x1 1/8 (14) screw pfh 8x1 1/8 (14 plcs) o1 - picket - w4l06901 5/8"x1 3/8"x13 1/4" (16x34x336) (7).
Page 37
Step 6 k5 j2 j2 screw pfh 8x1 3/4 (8) screw pfh 8x1 3/4 (8 plcs) k5 - serving shelf - w4l06902 5/8"x5 1/4"x40 7/8" (16x134x1038) (1) j2 - shelf support - w4l06903 1"x2 3/8"x2 3/8" (24x60x60) (2) back view.
Page 38
Step 7 lag screw wh 5/16x2 (1) lag screw wh 1/4x1-1/2 (2) lag screw wh 5/16x1 1/2 (3) washer lock ext 6x15 (2) washer lock ext 8x19 (4) m5 m2 j6 m2 - floor rail - w4l06897 5/8"x3 3/8"x43 1/4" (16x86x1097) (1) j6 - ladder rail - w4l06910 1"x2 3/8"x50 1/8" (24x60x1273) (1) m5 - floor rail - w4l06914 5...
Page 39
Step 8 h2 h2 m2 bolt wh 5/16x1 1/2 (2) lag screw wh 1/4x1-1/2 (4) washer lock ext 6x15 (4) t-nut 5/16 (5) washer lock ext 8x19 (4) h2 - deck brace - w4l06909 1"x3 3/8"x18 3/4" (24x86x475) (4) bolt wh 5/16x1 1/2 (2 plcs) washer lock ext 8x19 (2 plcs) t-nut 5/16 (3 plcs) lag screw wh 1/4x1-1/2 (4 plcs...
Page 40
Step 9 j3 bolt wh 5/16x1 1/2 (2) lag screw wh 1/4x1-1/2 (1) washer lock ext 6x15 (1) washer lock ext 8x19 (2) t-nut 5/16 (2) j3 - angle brace - w4l06905 1"x2 3/8"x47 1/4" (24x60x1200) (1) lag screw wh 1/4x1-1/2 bolt wh 5/16x1 1/2 (2 plcs) washer lock ext 6x15 washer lock ext 8x19 (2 plcs) t-nut 5/16...
Page 41
Step 10 j9 j9 j9 j9 screw pfh 8x1 3/4 (8) screw pfh 8x1 3/4 (8 plcs) m2 m5 j9 boards are flushed with the top of m2 and m5 boards. J9 - support board - w4l06064 1"x2 3/8"x3" (24x60x76) (4).
Page 42
Step 11 screw pfh 8x2 (4) h3 screw pfh 8x2 (4 plcs) h3 - floor support - w4l06915 1"x3 3/8"x40 7/8" (24x86x1038) (1).
Page 43
Step 12 lag screw wh 5/16x2 (2) washer lock ext 8x19 (2) j5 - awning support - w4l06908 1"x2 3/8"x11 3/4" (24x60x298) (2) lag screw wh 5/16x2 (2 plcs) washer lock ext 8x19 (2 plcs) j5 j5.
Page 44
Step 13 lag screw wh 5/16x2 (2) lag screw wh 1/4x1-1/2 (2) screw pfh 8x1 3/4 (4) washer lock ext 6x15 (2) washer lock ext 8x19 (2) j4 n1 j4 j4 - awning board - w4l06906 1"x2 3/8"x14 1/8" (24x60x358) (2) n1 - awning board - w4l06907 5/8"x2 3/8"x34 1/8" (16x60x866) (1) lag screw wh 5/16x2 (2 plcs) was...
Page 45
Step 14 y1 y2 m6 y2 - floor board - w4l06917 5/8"x4"x40 3/8" (16x102x1024) (1) y1 - floor board - w4l06916 5/8"x4"x40 3/8" (16x102x1024) (1) m6 - floor board - w4l06918 5/8"x3 3/8"x45 1/8" (16x86x1145) (10) screw pfh 8x1 1/2 (60 plcs) top view note hole. Y1 y2 screw pfh 8x1 1/2 (60).
Page 46
Step 15 k6 j7 bolt wh 5/16x1 1/2 (2) bolt wh 1/4x1/2 (2) washer lock ext 8x15 (2) nut barrel wh 1/4x5/8 (2) washer lock ext 8x19 (3) t-nut 5/16 (2) k6 - ground board - w4l06904 5/8"x5 1/4"x44 1/2" (16x134x1129) (1) j7 - ladder rail - w4l06911 1"x2 3/8"x50 1/8" (24x60x1273) (1) bolt wh 5/16x1 (1) nut...
Page 47
Step 16 bolt wh 5/16x2 (4) lag screw wh 5/16x1 1/2 (2) washer lock ext 8x19 (6) t-nut 5/16 (4) m7 m9 m7 m7 - wall rail - w4l06919 5/8"x3 3/8"x41 1/2" (16x86x1054) (2) m9 - wall rail - w4l06941 5/8"x3 3/8"x43 1/4" (16x86x1097) (1) lag screw wh 5/16x1 1/2 (2 plcs) washer lock ext 8x19 (2 plcs) bolt wh...
Page 48
Step 17 o4 o4 - awning board - w4l06957 5/8"x1 3/8"x32 1/4" (16x34x818) (1) - awning - a6p00124 1/64"x32 1/4"x22 1/4" (.4x818x566) (1) screw pfh 8x1 1/8 (4) screw pwh 8x5/8 (4) screw pfh 8x1 1/8 (4 plcs) screw pwh 8x5/8 (4 plcs) back view awning awning awning o4 m7 o4 board is flushed with the top o...
Page 49
Step 18 lag screw wh 5/16x1 1/2 (4) washer lock ext 8x19 (4) t-nut 5/16 (2) m11 m10 m10 - wall rail - w4l06942 5/8"x3 3/8"x43 1/4" (16x86x1097) (1) m11 - arched wall rail - w4l06943 5/8"x3 3/8"x43 1/4" (16x86x1097) (1) t-nut 5/16 (2 plcs) lag screw wh 5/16x1 1/2 (4 plcs) washer lock ext 8x19 (4 plcs...
Page 50
Step 19 bolt wh 5/16x1 1/2 (1) washer lock ext 8x19 (1) t-nut 5/16 (1) nut barrel wh 5/16x7/8 (1) washer lock ext 12x19 (1) bolt wh 5/16x1/2 (1) j8 j8 - wall board - w4l06947 1"x2 3/8"x25" (24x60x634) (1) bolt wh 5/16x1 1/2 washer lock ext 8x19 t-nut 5/16 bolt wh 5/16x1/2 washer lock ext 12x19 nut b...
Page 51
Step 20 washer lock int 8x15 (4) washer flat 9x18 (4) bolt pth 1/4x1 1/4 (2 plcs) washer lock int 8x15 (2 plcs) washer flat 9x18 (2 plcs) hand grip lime plastic (2 plcs) - hand grip lime plastic - a6p00127 (2) t-nut 1/4 (2 plcs) screw tapping 14x1-1/2 (2) t-nut 1/4 (2) screw tapping 14x1-1/2 (2 plcs...
Page 52
Step 21 1 13/16" 3 1/16" typ spacing o2 screw pfh 8x1 1/8 (14) screw pfh 8x1 1/8 (14 plcs) o2 - picket - w4l06944 5/8"x1 3/8"x18 1/4" (16x34x465) (7).
Page 53
Step 22 screw pfh 8x1 1/8 (18) o2 - picket - w4l06944 5/8"x1 3/8"x18 1/4" (16x34x465) (9) screw pfh 8x1 1/8 (18 plcs) 2 13/16" typ spacing 1 13/16" o2.
Page 54
Step 23 screw pfh 8x1 1/8 (14) o2 - picket - w4l06944 5/8"x1 3/8"x18 1/4" (16x34x465) (7) 3 1/16" typ spacing. 1 13/16" screw pfh 8x1 1/8 (14 plcs) o2.
Page 55
Step 24 h4 h5 h4 h5 bolt wh 5/16x2 1/4 (4) washer lock ext 8x19 (4) t-nut 5/16 (4) screw pfh 8x2 (8) h4 - horizontal tarp support - w4l06946 1"x3 3/8"x56 1/8" (24x86x1425) (2) h5 - horizontal tarp support - w4l06949 1"x3 3/8"x48 3/4" (24x86x1237) (2) bolt wh 5/16x2 1/4 (4 plcs) washer lock ext 8x19 ...
Page 56
Step 25 h6 h6 h6 h6 t1 screw pfh 8x1 1/2 (8) screw pfh 8x1 (8) screw pfh 8x1 (8 plcs) screw pfh 8x1 1/2 (8 plcs) h6 - roof board - w4l06950 1"x3 3/8"x40 3/8" (24x86x1025) (4) t1 - roof board - w4l06951 1"x1 3/8"x48 3/4" (24x34x1237) (1) 1/2" 5/8".
Page 57
Step 26 j10 - roof board - w4l06952 1"x2 3/8"x4" (24x60x102) (2) underneath j10 j10 screw pfh 8x1 (4) screw pfh 8x1 (4 plcs).
Page 58
Step 27 screw pfh 8x1 1/4 (8) y3 y3 n2 n2 n2 - roof board - w4l06953 5/8"x2 3/8"x33 1/8" (16x60x840) (2) y3 - sunburst half moon - w4l06954 5/8"x4"x12" (16x102x306) (2) 1 3/16" screw pfh 8x1 1/4 (8 plcs) screw pfh 8x1 1/8 (4 plcs) screw pfh 8x1 1/8 (4).
Page 59
Step 28 back view n3 n4 n4 n4 n3 n4 h6 h6 n4 boards flushed with h6 boards. Screw pfh 8x1 1/8 (18 plcs) n4 n4 n3 - sunburst board - w4l06955 5/8"x2 3/8"x11 3/4" (16x60x299) (2) n4 - sunburst board - w4l06956 5/8"x2 3/8"x8 1/8" (16x60x205) (4) screw pfh 8x1 1/8 (18).
Page 60
Step 29 screw pwh 8x5/8 (10) screw pwh 8x5/8 (10 plcs) tarp - tarp - a6p00123 43 1/4"x93 1/2" (1100x2374) (1).
Page 61
Step 30 m3 m4 lime hc rock #1 cranberry hc rock #1 blue hc rock #2 bolt pth 1/4x3/4 (12) washer lock int 8x15 (12) t-nut 1/4 (12) m4 - ladder rung - w4l06913 5/8"x3 3/8"x20 1/4" (16x86x515) (6) - lime hc rock #1 - a6p00128 (2) - blue hc rock #2 - a6p00040 (2) - cranberry hc rock #1 - a6p00129 (2) bo...
Page 62
Step 31 screw pfh 8x1 1/8 (2) m8 place telescope approximately center of m8 board. Telescope blue/lt.Blue screw pfh 8x1 1/8 (2 plcs) - telescope blue/lime - a6p00126 (1).
Page 63
Step 32 bench assembly bolt wh 5/16x1/2 (2) bolt wh 5/16x1/2 (2 plcs) bench assembly.
Page 64
Step 33 monkey bar assembly monkey bar assembly bolt wh 5/16x3/4 (2) bolt wh 5/16x3/4 (2 plcs).
Page 65
Step 34 washer split 5/16 (4) bolt hex 5/16x1 1/4 (4) washer flat 8x27 (4) swing beam assembly bolt hex 5/16x1 1/4 (4 plcs) washer split 5/16 (4 plcs) washer flat 8x27 (4 plcs) 5 1/8" screw pfh 6x3/4 (4 plcs) swing beam assembly screw pfh 6x3/4 (4) hc - byd id tag (large) 2011 with ages - a100164 (1...
Page 66
Step 35 lag screw wh 5/16x3 (1) washer flat 8x27 (1) ships wheel blue/lime washer flat 8x27 lag screw wh 5/16x3 - ships wheel blue/lime - a6p00125 (1).
Page 67
Step 36 chain blue 51.25" (4 plcs) swing seat blue (2 plcs) quick link (4 plcs) - chain blue 51.25" - a4m00524 (4) - chain blue 31" - a4m00525 (2) hd - swing seat blue - a6p00133 (2) fa - quick link - a100069 (6) quick link (2 plcs) blue trapeze - blue trapeze - a6p00134 (1).
Page 68
Step 37 slide assembly bolt wh 5/16x1/2 (3) t-nut 5/16 (3) 2 5/8" 5" 5" 1" 3 11/16" drill 3/8" (10mm) holes through floor (3 plcs) bolt wh 5/16x1/2 (3 plcs) t-nut 5/16 (3 plcs) slide assembly.
Page 69: «Spanish
Anchoring instructions final step double check every bolt, screw and nut for tightness. Make sure every board is secure and make sure the play set is level. Enjoy your new play set! Note: failure to use ground stakes can void warranty & cause injury! Step 38 tap in ground stakes at an approximate 45...
Page 70: Warranty
Warranty australian consumer law many of our products come with a guarantee or warranty from the manufacturer. In addition, they come with guarantees that cannot be excluded under the australian consumer law. You are entitled to a replacement or refund for a major failure and compensation for any ot...