1. DL manuals
  2. Backyard Discovery
  3. Toy
  4. Cedar Chateau 6511
  5. Owner's Manual

Backyard Discovery Cedar Chateau 6511 Owner's Manual

Manual is about: Play House

Summary of Cedar Chateau 6511

  • Page 1

    • • owner's manual • • frequently asked questions • • assembly instructions • • warranty information c c c ceeeed d d daaaarrrr c c c chhhhaaaatttteeeeaaaauuuu p p p pllllaaaayyyy h h h hoooouuuusssseeee m m m mooood d d deeeellll:::: # # # #6 6 6 65 5 5 511111111 manufacturer: backyard discovery 30...

  • Page 2: Stop

    Please have the following information when you make your call: 1 – model number of the product located on the front of the assembly manual 2 – desription of the part from the parts list por favor tenga visible la siguiente informaciÓn cuando llame: 1 - nÚmero de modelo del producto que se encuentra ...

  • Page 3

    Owner’s manual play house owner ph-2010 rev. 11/22/2010 brs dear customer: please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The company does not warranty any of ...

  • Page 4

    Owner’s manual play house owner ph-2010 rev. 11/22/2010 brs please refer to the assembly section of the assembly manual for maximum fall height. Positioning positioning positioning positioning your your your your play house play house play house play house 1. The play house is designed to be install...

  • Page 5

    Owner’s manual play house owner ph-2010 rev. 11/22/2010 brs the following chart explains the fall height in feet from which a life threatening head injury would not be expected critical heights in feet (m) of tested materials material uncompressed depth compressed depth 6" (152mm) 9" (228mm) 12" (30...

  • Page 6

    Owner’s manual play house owner ph-2010 rev. 11/22/2010 brs 5. Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sanding may be necessary to maintain a safe playing environment. If you are treating your play house with stain re...

  • Page 7

    Owner’s manual play house owner ph-2010 rev. 11/22/2010 brs appendix a information on playground surfacing materials: information on playground surfacing materials: information on playground surfacing materials: information on playground surfacing materials: the following information is from the uni...

  • Page 8

    Play set assembly manual faqs: 1. Does the area for the play house need to be level? Yes. Backyard discovery recommends the play house be positioned on a flat level area for maximum safety and durability. Any stakes provided should be used to secure it firmly to the ground. 2. What size area is reco...

  • Page 9

    Tools required for installation: (these are the tools that are generally required for assembly of our swing sets. These tools are not included in the swing set purchase.) (level 24") (open end wrenches 1/2" & 7/16") (nut drivers 1/2" & 9/16") (tape measure) (3/8" drive ratchet, 1/2" & 9/16" std sock...

  • Page 10

    S s s sa a a af f f fe e e e p p p pl l l la a a ay y y y a a a ar r r re e e ea a a a d d d diiiia a a ag g g gr r r ra a a am m m m s s s saaaaffffeeee p p p pllllaaaayyyy a a a arrrreeeeaaaa:::: • the safe play area refers to a zone extending 6' beyond the play product on all sides, including the...

  • Page 11

    Parts identification wood components (not to scale) f1 - counter support - w101809 1 3/8"x2 3/8"x9 7/8" (36x60x250) (2) h1 - seat support - w101823 1"x3 3/8"x18 7/8" (24x86x480) (2) h2 - seat leg - w101804 1"x3 3/8"x11 3/4" (24x86x298) (2) h3 - seat support - w101805 1"x3 3/8"x6 1/2" (24x86x166) (2)...

  • Page 12

    Parts identification wood components (not to scale) m17 - seat support - w101807 5/8"x3 3/8"x6 1/2" (16mm x 86mm x 166mm) (1) m18 - window shelf support - w101824 5/8"x3 3/8"x6 1/2" (16x86x166) (2) m19 - flower box bottom - w101833 5/8"x3 3/8"x8 1/4" (16x86x210) (2) n1 - roof ridge cap right - w1018...

  • Page 13

    Parts identification wood components (not to scale) (1) wp - porch gable - w101836 (1) wp4 - left front wall - w101840 (1) wp5 - right front wall - w101839 (1) wp3 - back wall - w101782 (1) wp2 - right wall - w101780 (1) wp1 - left wall - w101781 r2 - porch roof slat right - w101841 3/4"x5 1/2"x12" ...

  • Page 14

    Parts identification wood components (not to scale) (1) wp6 - door - w101813 (1) wp7 - front gable - w101837 (1) wp10 - front gable - w101838 (1) wp8 - left window - w102100 (1) wp9 - right window - w102101 (2) rp1 - roof panel - w101828.

  • Page 15

    Parts identification hardware br - screw pfh 8x1-1/8" - h100088 (52) bq - screw pfh 8x1-1/4" - h100087 (64) bp - screw pfh 8x1-1/2" - h100086 (146) bs - screw pfh 8x1-3/4" - h100089 (28) cx - screw #4x5/8" - h100127 (22) cv - screw wood 8x1/2" - h100124 (15) bn - screw pfh 8x1" - h100085 (10) ks - n...

  • Page 16

    Parts identification a a a acccccccceeeessssssssoooorrrriiiieeeessss (not to scale) df - window frame white 343x444.5 - a100013 (6) fl - clock - a100078 (1) js - square sink bowl - a100129 (1) mr - door bell - a100174 (1) my - double magnetic catch kit - a100261 mag catch (1) hz - knob - a100071 (1)...

  • Page 17

    Assembly phase 1 phase notes • assemble with hardware as shown. • for ease during assembly, assemble uprights flat on the ground. Hardware needed: • (8) bn - screw pfh 8x1 - h100085 • (40) bq - screw pfh 8x1-1/4 - h100087 • (24) bc - screw pfh 8x3/4 - h100070 parts needed: • (4) l5 - bay window ledg...

  • Page 18

    Assembly phase 2 phase notes • assemble with hardware as shown. Parts needed: • (1) k3 - window shelf - w101825 • (2) m18 - window shelf support - w101824 • (1) m20 - window sill board - w101843 • (2) m19 - flower box bottom - w101833 • (4) l9 - flower box side - w101834 • (2) l7 - flower box front ...

  • Page 19

    Phase notes • assemble with hardware as shown. Assembly phase 3 step 1: attach 'p1' post uprights to 'wp3' back wall using hardware 'mw', 'kv' & 'be', as shown. Parts needed: • (1) wp3 - back wall - w101782 • (2) p1 - post upright - w101783 hardware needed: • (6) mw - bolt wh 1/4x2 - h100160 • (6) k...

  • Page 20

    Assembly phase 4 phase notes • assemble with hardware as shown. Hardware needed: • (6) mw - bolt wh 1/4x2 - h100160 • (6) kv - washer lock ext 6x15 - h100138 • (6) be - t-nut 1/4 - h100072 parts needed: • (1) wp1 - left wall - w101781 • (1) p1 - post upright - w101783 step 1: attach 'p1' post uprigh...

  • Page 21

    Assembly phase 5 phase notes • assemble with hardware as shown. Parts needed: • (1) wp2 - right wall - w101780 • (1) p1 - post upright - w101783 hardware needed: • (6) mw - bolt wh 1/4x2 - h100160 • (6) kv - washer lock ext 6x15 - h100138 • (6) be - t-nut 1/4 - h100072 step 1: attach 'p1' post uprig...

  • Page 22

    Assembly phase 6 phase notes • assemble with hardware as shown. Parts needed: • (1) wp4 - left front wall - w101840 • (1) wp5 - right front wall - w101839 • (1) mv - metal tie strap - a100257 • (2) mt - plastic window medium white - a100014 hardware needed: • (6) mw - bolt wh 1/4x2 - h100160 • (6) k...

  • Page 23

    Assembly phase 7 phase notes • assemble with hardware as shown. Parts needed: • (2) n19 - filler block - w101832 • (1) p2 - center filler block - w101831 • (1) wp10 - front gable - w101838 hardware needed: • (8) br - screw pfh 8x1-1/8 - h100088 • (3) bp - screw pfh 8x1-1/2 - h100086 step 1: pre-dril...

  • Page 24

    Assembly phase 8 phase notes • assemble with hardware as shown. Parts needed: • (1) wp7 - rear gable - w101837 hardware needed: • (3) br - screw pwh 8x1-1/8 - h100088 step 1: using 'wp7' roof gable as a template, pre-drill & attach 'wp7' rear gable to 'wp3' back wall using screws 'br', as shown. Not...

  • Page 25

    Phase notes • assemble with hardware as shown. Assembly phase 9 parts needed: • (2) bay window assembly hardware needed: • (12) bp - screw pfh 8x1-1/2 - h100086 step 2: using the holes located in 'wp3' as a template, pre-drill & attach bay window assembly to 'wp3' back wall using screws 'bp', as sho...

  • Page 26

    Assembly phase 10 phase notes • assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with a 1/8" drill bit, before attaching. Note: it is vital that the fort be level before and after each phase of assembly. Rp1 rp1 bp wp10 bp bp wp7 o1 br rp1 br rp1 n1 slide th...

  • Page 27

    Assembly phase 11 parts needed: • (1) wp - porch gable - w101836 • (4) r2 - porch roof slat right - w101841 • (4) r3 - porch roof slat left - w101842 • (1) o10 - ridge cap left - w101820 • (1) n14 - ridge cap right - w101821 • (2) m10 - porch rafter back - w101822 phase notes • assemble with hardwar...

  • Page 28

    Assembly phase 12 parts needed: • (1) porch assembly phase notes • assemble with hardware as shown. Hardware needed: • (6) br - screw pfh 8x1-1/8 - h100088 step 1: pre-drill & attach porch assembly to 'wp10' front gable using screws 'br', as shown. To prevent board splitting, you must pre-drill each...

  • Page 29

    Assembly phase 13 parts needed: • (1) window shelf assembly phase notes • assemble with hardware as shown. Hardware needed: • (3) bp - screw pfh 8x1-1/2 - h100086 • (2) bt - screw pfh 8x2-1/2 - h100090 step 1: pre-drill & attach window shelf assembly to 'wp2' right wall using screws 'bp' & 'bs', as ...

  • Page 30

    Assembly phase 14 parts needed: • (1) wp8 - left window - w101826 • (1) wp9 - right window - w101827 • (4) fr - hinge - a100093 phase notes • assemble with hardware as shown. Hardware needed: • (20) cx - screw #4x5/8 - h100127 to prevent board splitting, you must pre-drill each board with a 1/8" dri...

  • Page 31

    Assembly phase 15 parts needed: • (1) n20 - window stop - w101814 • (1) my - magnetic catch kit - double - a100261 phase notes • assemble with hardware as shown. Hardware needed: • (2) br - screw pfh 8x1-1/8 - h100088 step 2: attach 'my' magnetic catch to 'n20' window stop using pan head screws prov...

  • Page 32

    Assembly phase 16 hardware needed: • (8) bp - screw pfh 8x1-1/2 - h100086 parts needed: • (2) flower box assembly phase notes • assemble with hardware as shown. Step 1: pre-drill & attach flower box assembly to 'wp4' & 'wp5' front walls using screws 'bp', as shown. Note: it is vital that the fort be...

  • Page 33

    Assembly phase 17 hardware needed: • (2) ks - nut barrel wh 1/4x5/8 - h100136 • (2) kw - washer lock ext 8x15 - h100139 • (2) kv - washer lock ext 6x15 - h100138 • (2) kt - bolt wh 1/4x1 - h100137 • (24) bs - screw pfh 8x1-3/4 - h100089 • (4) br - screw pfh 8x1-1/8 - h100088 parts needed: • (2) h1 -...

  • Page 34

    Assembly phase 18 parts needed: • (1) bench assembly phase notes • assemble with hardware as shown. Step 1: attach bench assembly to 'wp2' right wall using "safe-t-fuse" hardware, as shown. Step 2: attach bench assembly to 'wp2' right wall using "safe-t-fuse" hardware, as shown. Hardware needed: • (...

  • Page 35

    Assembly phase 19 hardware needed: • (4) bp - screw pfh 8x1-1/2 - h100086 • (20) bq - screw pfh 8x1-1/4 - h100087 parts needed: • (2) f1 - counter support - w101809 • (2) k6 - counter support - w101812 • (1) k1 - front counter board - w101810 • (1) k2 - front counter board - w101811 phase notes • as...

  • Page 36

    Assembly phase 20 hardware needed: • (4) br - screw pfh 8x1-1/8 - h100088 parts needed: • (1) jx - stove assembly - a100136 • (1) js - square sink bowl - a100129 phase notes • assemble with hardware as shown. Step 1: pre-drill & attach 'jx' stove assembly to counter assembly using screws 'br', as sh...

  • Page 37

    Bl parts needed: • (1) ms - phone kit - a100132 • (1) jr - faucet kit - a100125 phase notes • assemble with hardware as shown. Hardware needed: • (2) bq - screw pfh 8x1-1/4 - h100087 • (2) cv - screw wood pfh 8x1/2 - h100124 assembly phase 21 step 1: attach 'jr' faucet kit to counter assembly using ...

  • Page 38

    Parts needed: • (1) fl - clock - a100078 • (1) mr - door bell - a100174 phase notes • assemble with hardware as shown. Hardware needed: • (2) bc - screw pfh 8x3/4 - h100070 • (2) bn - screw pfh 8x1 - h100085 assembly phase 22 step 1: attach 'fl' clock to 'wp3' right wall using screws 'bc', as shown....

  • Page 39

    Parts needed: • (1) wp6 - door - w101813 • (1) hz - knob - a100071 • (2) fs - hinge (door, spring loaded - a100094 phase notes • assemble with hardware as shown. Hardware needed: • (1) bq - screw pfh 8x1-1/4 - h100087 • (6) cv - screw pfh 8x1/2 - h100124 assembly phase 23 to prevent board splitting,...

  • Page 40

    Parts needed: • (1) pw6 - door - a101813 phase notes • assemble with hardware as shown. Hardware needed: • (6) cv - screw pfh 8x1/2 - h100124 assembly phase 24 step 1: attach 'wp6' door to 'wp4' left front wall using screws 'cv', as shown. Note: it is vital that the fort be level before and after ea...

  • Page 41

    Limited warranty limited warranty limited warranty limited warranty this limited warranty by backyard discovery applies to products manufactured under the backyard discovery brand or its other brands including but not limited to backyard botanical, adventure playsets, and leisure time products. Back...

  • Page 42

    Lead to product failure and potential injury. Any and all public use will void this warranty. Backyard discovery disclaims all other representations and warranties of any kind, express or implied. This warranty gives you specific legal rights. You may have other rights as well which vary from state ...