Summary of BF-462
Page 1
User’s manual usb 2.0 pci card bf-462.
Page 2
Usb 2.0 pci card user’s manual 1 1.Introduction bf-462 is a pci card fully functional of usb 2.0 host, which supports high-speed, full-speed, & low-speed operation and follows the enhanced host controller interface (ehci) specification. 2.Package content hardware: usb 2.0 pci card software: driver s...
Page 3
Usb 2.0 pci card user’s manual 2 5.Hardware installation 5.1 turn off your computer, unplug the power cord, disconnect all peripheral devices and remove the pc case. 5.2 locate the pci slots on the motherboard; remove any add-on card, which blocks easy access to the pci slots. 5.3 take the usb 2.0 p...
Page 4
Usb 2.0 pci card user’s manual 3 6.Software installation (windows ® 98, me as example) 6.1 windows ® 98 driver installation 6.1.1 power on the computer, windows ® will detect an unknown device and run the “add new hardware wizard” to assist you in setting up the new device. 6.1.2 insert the driver o...
Page 5
Usb 2.0 pci card user’s manual 4 6.1.5 select the updated driver (recommended), and then click “next” to continue. 6.1.6 windows ® will detect the suitable driver; click “next” to continue. 6.1.7 windows ® will install the driver to your system..
Page 6
Usb 2.0 pci card user’s manual 5 6.1.8 when the windows ® appears as step 6.1, repeat the steps 6.1.1 to 6.1.7. 6.1.9 when the windows ® appears as below, click “next” to continue. 6.1.10 select “search for the best driver for your device” and click “next”.
Page 7
Usb 2.0 pci card user’s manual 6 6.1.11 select specify a location and browse the driver’s location “d:\win98me” in the dialog (d: represents the cd-rom drive), then click “next” to continue. 6.1.12 when the windows ® appears as below, click “next” to continue. 6.1.13 after installation is complete, ...
Page 8
Usb 2.0 pci card user’s manual 7 6.2 windows ® 2000 driver installation 6.2.1 power on the computer, windows ® will detect an unknown device and run the “add new hardware wizard” to assist you in setting up the new device. 6.2.2 insert the driver of usb 2.0 pci card into cd-rom drive, click “next” t...
Page 9
Usb 2.0 pci card user’s manual 8 6.2.5 browse the driver’s location ”d:\win2kxpehcd.Inf” in the dialog (d: represents the cd-rom drive), and then click “ok” 6.2.6 click “next” to continue. 6.2.7 windows ® will install the driver to your system. 6.2.8 click “finish” to complete the setup procedure..
Page 10
Usb 2.0 pci card user’s manual 9 6.2.9 after install the driver, you have to check the “control panel”- “system”-“hardware”-“device manager” to make sure that the driver has already installed properly.In the universal serial bus controller you can see the nec pci to usb enhanced controller and nec p...
Page 11
Usb 2.0 pci card user’s manual 10 6.3 windows ® xp driver installation 6.3.1 power on the computer, windows ® will detect an unknown device and run the “add new hardware wizard” to assist you in setting up the new device. 6.3.2 insert the driver of usb 2.0 pci card into cd-rom drive, click “next” to...
Page 12
Usb 2.0 pci card user’s manual 11 6.3.6 windows ® will install the driver to your system. 6.3.7 click “finish” to finish the setup procedure. 6.3.8 after finished install the driver, you should go to the “control panel”- “system”-“hardware”-“device manager” to check the universal serial bus controll...
Page 13
Usb 2.0 pci card user’s manual 12 7.Fcc statement this device generates and uses radio frequency and may cause interference to radio and television reception if not installed and used properly. This has been tested and found to comply with the limits of a class b computing device in accordance with ...