Industrial metalsawing bandsaw blades global precision.
Ii introduction consistency. To achieve this, we operate within the snap on qfs quality system or quality forward system, which uses the iso 9001:2000 framework. It includes a continually improving quality management system, which includes a focus on customer requirements and satisfaction. All stage...
Key production processes tooth forming high technology milling and grinding processes are used for precision tooth forming enabling sharper and stronger teeth to be produced. Setting computer controlled measuring devices and camera monitoring systems check every tooth. This information is collated a...
2 service storage and distribution ndc - new distribution concept - is one of our single largest investments in customer service. It comprises two distribution centres in europe and two in north america. Modern on-line computer processes ensure prompt and reliable deliveries and minimise stock handl...
Research and development the research and development centre for bandsaws is a state-of-the art laboratory located in lidkoping, sweden. The centre, which develops and tests metal cutting saws, is staffed by qualified engineers and metallurgists and is equipped with machines and instruments for meas...
4 bandsaw selection guide page metal cutting maximum performance bandsaws specially designed for the greatest variety of metal cutting applications. Non-ferrous cutting maximum performance bandsaws specially designed for non-ferrous cutting applications such as brass, bronze and aluminium. Also an e...
Large & medium solids small solids & bundles pipes, profiles, castings contours mandatory protective gloves mandatory eye protection 5 bandsaw selection guide.
6 general information band length the length of a bandsaw blade depends upon the sawing machine being used. Information for specific machines can be found in our software program, bandcalc tm , see page 28, or from your sawing machine manufacturer. Band width the band width is measured from the tip ...
Teeth per inch (tpi) the number of teeth per inch (tpi) defines the pitch of the blade and can vary from less than 1 to 24. Thin-walled workpieces like tubes, pipes, sheet etc., require fine teeth, otherwise there is a risk of tooth damage or breakage. Large cross sections should be cut with a coars...
General information 8 feed rate/chips it is important that each tooth of the bandsaw blade cuts a chip with the right thickness. This is determined by the selection of tooth pitch, band speed and feed rate. Start by selecting the right tooth pitch from the diagrams on page 9 and 10 then set your ban...
General infor m ation 9 tooth pitch for solid workpieces the diagram below will help you select the right pitch for cutting solids. The ideal choice is at the widest point of each field. Example 1: when cutting a Ø 6 inch (150 mm) bar, use 2 tpi, if an evenly pitched blade is your choice. Use a 2/3 ...
10 general information cutting pipes and profiles the diagram below will help you find the right tooth pitch for cutting pipes and profiles. The recommended tooth pitch for cutting profiles is found in the field where the width meets the wall thickness of the profile. Example 3: when cutting a 4" x ...
Tooth shape guide regular is a standard tooth shape with 0˚ rake angle. Regular is the traditional tooth shape for general cutting of small, solid workpieces. Positive ps has a 10˚-15˚ rake angle, a curved back and a gullet with large chip capacity. It is excellent for cutting large workpieces of al...
Production cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 12 dimensions teeth tooth product mm inches per inch type code ▼ 27 x 0.9 1 x .035 3 positive ps 3851-27-0.9-p-3 4 positive ps 3851-27-0.9-p-4 4 regular 3851-27-0.9-r-4 6 regular 3851-27-0.9-r-...
Pr oduction cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 13 3851 — sandflex ® cobra ™ psg ™ for production cutting of medium to large sections on various materials, especially alloyed and stainless steels • specially designed in combination with sha...
Production cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 14 3854 – sandflex ® king cobra ® phg ™ for high productivity cutting of difficult-to-cut materials • special design in combination with sharp cutting edges for easy penetration in difficult to...
▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ dimensions teeth tooth product mm inches per inch type code ▼ 34 x 1.1 1-1/4 x .042 2 tsx 3868-34-1.1-tsx-2 2/3 tsx 3868-34-1.1-tsx-2/3 3/4 tsx 3868-34-1.1-tsx-3/4 41 x 1.3 1-1/2 x .050 1.4/2 tsx 3868-41-1.3-tsx-...
Other production/special purpose cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 16 3851 — sandflex ® cobra ™ for contour and high productivity cutting of small workpieces • specially designed tooth shapes for maximum cutting performance. • m42 tooth t...
Other pr oduction/special purpose cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 17 3852 — sandflex ® die-band ™ for contour sawing of tool and mould steels • precisely set for accurate cutting. • positive rake teeth for easy feed. • m42 tooth tips pr...
Other production/special purpose cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 18 3853 — sandflex ® fabricator ™ for bundle cutting of tubes and structural steel • special set prevents blade from binding in the cut. • special tooth shape for extra to...
Multi-purpose cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 19 multi-purpose 3850 — sandflex ® dragon ™ for easy-to-cut steels • multi-purpose tooth shapes for a variety of applications. • matrix hss edge provides tough, impact-resistant teeth which ...
Multi-purpose ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 20 3850 — sandflex ® portable bandsaw blades for portable hand held machines • multi-purpose tooth shapes for a variety of applications. • tough impact - resistant teeth offer long life and good sur...
3862 — sandflex ® compensator ™ for light machines with limited feed force • positive rake combo pr teeth give excellent surface finish and long blade life. • m42 edge provides hard teeth for difficult-to-cut steels. Dimensions teeth tooth product mm inches per inch type code 27 x 0.9 1 x .035 3/4 c...
22 multi-purpose ▼ 3856 — sandflex ® multi-cut ™ for multi-purpose applications on lighter machine types of manual or semi-automatic design • large range of tooth pitches and standard loop lengths to meet the needs of most multi-purpose applications. • m42 tooth tips offer good heat and wear resista...
Non-ferrous cutting ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 3850 — sandflex ® dragon ™ for horizontal machines • positive hook toothing for good penetration and chip formation. • tough matrix hss tooth tips. • large gullets for good chip carrying capac...
24 non-ferrous cutting ▼ 3852 — sandflex ® die-band ™ for vertical machines and contour cutting • positive rake teeth make hand-fed cutting easy. • m42 tooth tips provide wear resistance for long life. Dimensions teeth tooth product mm inches per inch type code 6 x 0.6 1/4 x .025 6 hook 3852-6-0.6-h...
▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 3861— sandflex ® nf ™ economical bi-metal blade for non-ferrous cutting • hook toothing for easy feeding. • new regular pitches. • durable spring steel backing. • extended tool life dimensions teeth tooth product...
26 non-ferrous cutting 3869 — carbide triple set ® foundry bandsaw blade for non-ferrous and abrasive materials • carbide tipped teeth with triple set configuration. • fast cutting. • easy feeding. • straight and radius cutting. • special design for foundry use. • for use on smaller machines for dif...
Carbide grit ▼ ▼ large & medium solids small solids & bundles pipes, profiles, castings contours ▼ ▼ 27 carbide grit dimensions teeth tooth product mm inches per inch type code ▼ 3866 — multi-grit carbide grit-edge blade for cutting ceramics, tyres, graphite, fibreglass, cables, composite materials,...
28 sawing aids 3870 — bandcalc ™ a software program, based upon input from users with regards to material, machine, workpiece, economy and customer preferences, will recommend the best bandsaw blade for the application. It will also give necessary information on blade speed, feed rate and will calcu...
3870 tensionmeter proper tension is necessary to provide straight cuts and long blade life, thereby reducing the cost per cut. Bahco’s tensionmeter is designed for easy, accurate measurement of the correct blade tension of all bandsaws. Product ean code code 731151+ 3870-tension meter 8145637 1 678 ...
30 troubleshooting guide important facts band breakage crooked sawing guides and guide arms guides too far apart check and adjust the guides regularly. Guides worn out guides worn out check if worn out and replace if necessary. Guide setting too wide guide arm loose position guide arms as close to t...
Tooth breakage rough surface rapid tooth wear vibration band slips on wheel guides too far apart guides poorly adjusted driving wheel worn out chip brush chip brush not working not working – gullets filled band tension too low band tension too low too little coolant incorrect coolant concentration b...
32 packaging information loop packaging/bimetal and carbide 3866, 3868, 3869 width length, mm/ft mm inches 3001 – 3660 3661 – 4120 4121 – 5334 >5335 9'10" – 12'0" 12'1" – 13'6" 13'7" – 17'5" >17'5" 5 5 5 5 5 16-27 5/8-1 5 5 2 or 5 2 or 5 2 or 5 34 1-1/4 2 or 5 2 or 5 2 or 5 2 2 41-80 1-1/2 – 3-1/8 2...
Order form/enquiry form ▼ now contact us… company name: contact name: street: city: region: postcode: country: telephone: technical support material: size (mm): surface condition: clamping: single bundle (how many pieces) bandsaw blade size: mm length mm width mm thickness type of machine: inquiry o...
Www.Bahco.Com bahco copyright 2003 argentina bahco argentina s.A. Buenos aires phone: 11 44 84 05 57 fax: 11 44 84 44 63 australia bahco tools pty. Ltd. Wetherill park, n.S.W. 2164 phone: 02-98 28 06 60 fax: 02-98 28 06 65 austria bahco belzer gmbh wien phone: (0)1 272 45 77 fax: (0)1 272 45 77-29 b...