1. DL manuals
  2. Baileigh
  3. Power Tool
  4. DP-1512B-HD
  5. Operator's Manual

Baileigh DP-1512B-HD Operator's Manual

Summary of DP-1512B-HD

  • Page 1

    Operator’s manual drill press model: dp-1512b-hd and dp-1512f-hd © 2016 baileigh industrial, inc. Reproduction of this manual in any form without written approval of baileigh industrial, inc. Is prohibited. Baileigh industrial, inc. Does not assume and hereby disclaims any liability for any damage o...

  • Page 2: Table Of Contents

    Table of contents thank you & warranty .......................................................................................... 1 introduction ............................................................................................................. 3 general notes ................................

  • Page 3

    1 1 thank you & warranty thank you for your purchase of a machine from baileigh industrial. We hope that you find it productive and useful to you for a long time to come. Inspection & acceptance. Buyer shall inspect all goods within ten (10) days after receipt thereof. Buyer’s payment shall constitu...

  • Page 4

    2 2 force majuere. Seller shall not be responsible for any delay in the delivery of, or failure to deliver, goods due to causes beyond seller’s reasonable control including, without limitation, acts of god, acts of war or terrorism, enemy actions, hostilities, strikes, labor difficulties, embargoes,...

  • Page 5

    3 3 introduction the quality and reliability of the components assembled on a baileigh industrial machine guarantee near perfect functioning, free from problems, even under the most demanding working conditions. However if a situation arises, refer to the manual first. If a solution cannot be found,...

  • Page 6: Important

    4 4 learn to recognize safety information this is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury! Follow recommended precautions and safe operating practices. Understand signal words a signal word – danger, warning, ...

  • Page 7

    5 5 save these instructions. Refer to them often and use them to instruct others. Protect eyes wear safety glasses or suitable eye protection when working on or around machinery. Protect against noise prolonged exposure to loud noise can cause impairment or loss of hearing. Wear suitable hearing pro...

  • Page 8: Warning:

    6 6 safety precautions wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal ...

  • Page 9

    7 7 7. Drill operation. Never start the drill press with the drill bit pressed against the piece part. Feed the drill bit slowly and evenly into the piece part. Position work to avoid drilling into the table. 8. Clearing chips. Turn the machine off and clear chips and scrap pieces with a brush or wi...

  • Page 10

    8 8 24. Inspect power and control cables periodically. Replace if damaged or bare wires are exposed. Bare wiring can kill! 25. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords. Keep visitors a safe distance from the work ...

  • Page 11

    9 9 technical specifications description dp-1512b dp-1512f type belt drive belt drive motor 3/4hp (.55kw) / 60hz / 10a 3/4hp (.55kw) / 60hz / 10a power supply 110vac 60hz 110vac 60hz spindle speed 550 ~ 2500rpm 550 ~ 2500rpm spindle taper mt2 mt2 chuck size 5/8" (16mm) 5/8" (16mm) collar diameter 2....

  • Page 12: Warning:

    10 10 unpacking and checking contents your baileigh machine is shipped complete. Separate all parts from the packing material and check each item carefully. Make certain all items are accounted for before discarding any packing material. Cleaning your machine may be shipped with a rustproof waxy coa...

  • Page 13

    11 11 separate all parts from packaging materials and check each item make sure all items are accounted for before discarding any packing material. Item description qty. A table 1 b column support arm 1 c owner's manual 1 d bag of loose parts * e base * f head assembly 1.

  • Page 14

    12 12 transporting and lifting important: lifting and carrying operations should be carried out by skilled workers, such as a truck operator, crane operator, etc. If a crane is used to lift the machine, attach the lifting chain carefully, making sure the machine is well balanced. Follow these guidel...

  • Page 15

    13 13 installation important: consider the following when looking for a suitable location to place the machine:  overall weight of the machine.  weight of material being processed.  sizes of material to be processed through the machine.  space needed for auxiliary stands, work tables, or other m...

  • Page 16

    14 14 anchoring the machine  once positioned, anchor the machine to the floor, as shown in the diagram, using bolts and expansion plugs or sunken tie rods that connect through holes in the base of the stand. If you intend to mount the baileigh machine on a workbench be aware of the following:  ove...

  • Page 17: Warning:

    15 15 assembly and set up most of your drill press has been assembled at the factory, but some parts must be assembled or installed after delivery. 1. Position the base of solid stable surface suitable to support the entire drill press when fully assembled. 2. Starting with the base, place the colum...

  • Page 18

    16 16 13. Using a lifting device or an assistant, lift the head assembly over the column and insert the column into the pocket on the bottom of the head assembly until the column is fully seated into the head pocket, approximately 4” (100mm). 14. Position the headstock directly over the base by usin...

  • Page 19

    17 17 21. Install the chuck guard onto the spindle shaft until the bottom edge of the guard is flush with the bottom edge of the spindle. 22. Firmly tighten the clamping screw but do not over tighten and break the c lamping ring..

  • Page 20

    18 18 drill chuck and arbor the drill chuck attaches to the drill spindle by means of a drill chuck arbor. Matched tapers on the arbor and chuck bore create solid assembly when properly joined. To assemble the drill chuck and mount it to the spindle, carefully follow the instructions below: importan...

  • Page 21

    19 19 arbor removal a drift key is included to aid in the drill chuck arbor removal. 1. Extend the spindle downward until the slot is exposed in the side of the quill. 2. Rotate the spindle until the inner slot is aligned with the outer as shown. You will see through the spindle when the slot is pro...

  • Page 22: Caution:

    20 20 electrical motor specifications your tool is wired for 110 volt, 60hz alternating current. Before connecting the tool to the power source, make sure the machine is cut off from power source. Considerations  observe local electrical codes when connecting the machine.  the circuit should be pr...

  • Page 23

    21 21  improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is nec...

  • Page 24: Caution:

    22 22 operating precautions the following operating and safety precautions must be observed in order to avoid harm to the operator or damage to the drill press. 1. Safety is the responsibility of the user/purchaser since conditions differ between jobs. Use and enforce safety procedures at each opera...

  • Page 25

    23 23 8. Use the adjustment knob on the left side of the drill head to adjust the spindle speed as needed. Important: never adjust the spindle speed when the drill is stopped. Only adjust the spindle speed when the drill is running safely at full power. Adjusting the speed when stopped can damage th...

  • Page 26

    24 24 indication of extreme speeds and feeds a drill that splits up the web is evidence of too much feed or insufficient tip clearance at the center as a result of improper grinding. The rapid wearing away of the extreme outer comers of the cutting edges indicates that the speed is too high. A drill...

  • Page 27

    25 25 alignment pointer adjustment this machine is equipped with an alignment pointer. The pointer is used to indicated the point on the material that the tip of the drill (center point of the drilled hole) contact first. 1. Set up the drill with the desired bit, and position the table and material ...

  • Page 28: Warning:

    26 26 machine adjustment depth stop your drill press comes with a depth stop adjustment for use when drilling. 1. Loosen the depth collar lock knob (a). 2. Secure the wood stock you will be drilling onto the drill press table. 3. With the desired bit installed, lower the spindle until the tip of the...

  • Page 29

    27 27 table adjustment the table can be adjusted for height, rotation and angle. 1. Loosen the support bracket lock knob. Turn the table hand crank to lift or lower the table. 2. Always lock the support bracket in place before operating the machine. Adjust rotation: 1. Loosen the lock handle located...

  • Page 30: Warning:

    28 28 lubrication and maintenance daily maintenance  inspect the power plug and cord.  keep area around machine clear of debris.  check daily for any unsafe conditions and fix immediately.  check that all nuts and bolts are properly tightened.  frequently blow out any dust that may accumulate i...

  • Page 31

    29 29 storing machine for extended period of time if the drill press is to be inactive for a long period of time, prepare the machine as follows:  detach the plug from the electrical supply panel.  clean and grease the machine.  cover the machine. Wiring diagram cover switch 1 2 laser switch 1 2 ...

  • Page 32

    30 30 dp-1512b-hd parts diagram.

  • Page 33

    31 31 dp-1512b-hd parts list item description qty. Item description qty. 1 base 1 67 wedge 1 2 screw 4 68 screw 1 3 spring washer 4 69 nut 1 4 rack 1 70 self-tapping screw 2 5 column 1 71 screw 1 6 collar 1 72 nut 1 7 screw 1 73 flange nut 2 8 crank 1 74 screw 2 9 screw 1 75 protect mirror 1 10 pin ...

  • Page 34

    32 32 item description qty. Item description qty. 34 screw 2 97 line clip 5 35 indicator 1 98 bolt 4 36 screw 1 99 washer 1 37 screw 1 100 plug 1 38 screw 1 101 allen key 1 39 screw 2 102 allen key 1 40 insulation board 1 103 screw 2 41 scale 1 104 nut 2 42 rivet 2 105 nut 2 43 scale 1 106 screw 2 4...

  • Page 35

    33 33 dp-1512f-hd parts diagram.

  • Page 36

    34 34 dp-1512f-hd parts list item description qty. Item description qty. 1 base 1 86 pulley cover 1 2 bolt 4 87 bearing seat 2 3 rack 1 88 bearing 2 4 column 1 89 lower movable pulley (middle) 1 5 collar 1 90 screw 2 6 screw 1 91 fixed pulley (middle) 1 7 table support seat 1 92 upper movable pulley...

  • Page 37

    35 35 item description qty. Item description qty. 38 screw 2 119 plastic seat 1 39 bolt 2 120 sensor 1 40 switch 1 121 screw 2 41 plastic plate 1 122 flat washer 2 42 switch box 1 123 nut 2 43, 44, 119, 120 digital display set 1 124 sensor support 1 45 terminal 1 125 retaining ring 1 46 copper 2 126...

  • Page 38

    36 36 item description qty. Item description qty. 70 speed range label 1 151 micro-switch 1 71 cable 1 152 nut 2 72 allen key 1 153 pan head screw 2 73 allen key 1 154 terminal 1 74 screw 2 155 insulator 1 75 spring seat 1 156 plate key 1 76 quill spring 1 157 plate key 1 77 spring cover 1 158 plate...

  • Page 39

    37 37 notes.

  • Page 40

    38 38 baileigh industrial, inc. 1625 d ufek d rive m anitowoc , wi 54220 p hone : 920. 684. 4990 f ax : 920. 684. 3944 www . Baileigh . Com baileigh industrial, inc. 1455 s. C ampus a venue o ntario , ca 91761 p hone : 920. 684. 4990 f ax : 920. 684. 3944 baileigh industrial ltd. U nit 1 f ullwood c...