Jointer / planer model: jp-1898-nc © 2012 baileigh industrial, inc. Reproduction of this manual in any form without written approval of baileigh industrial, inc. Is prohibited. Baileigh industrial, inc. Does not assume and hereby disclaims any liability for any damage or loss caused by an omission o...
Table of contents thank you & warranty .......................................................................................... 1 introduction ............................................................................................................ 3 general notes..................................
1 1 thank you & warranty thank you for your purchase of a machine from baileigh industrial. We hope that you find it productive and useful to you for a long time to come. Inspection & acceptance. Buyer shall inspect all goods within ten (10) days after receipt thereof. Buyer’s payment shall constitu...
2 2 force majuere. Seller shall not be responsible for any delay in the delivery of, or failure to deliver, goods due to causes beyond seller’s reasonable control including, without limitation, acts of god, acts of war or terrorism, enemy actions, hostilities, strikes, labor difficulties, embargoes,...
3 3 introduction the quality and reliability of the components assembled on a baileigh industrial machine guarantee near perfect functioning, free from problems, even under the most demanding working conditions. However if a situation arises, refer to the manual first. If a solution cannot be found,...
4 4 learn to recognize safety information this is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury! Follow recommended precautions and safe operating practices. Understand signal words a signal word – danger, warning, ...
5 5 save these instructions. Refer to them often and use them to instruct others. Protect eyes wear safety glasses or suitable eye protection when working on or around machinery. Blade hazard keep hands and fingers away from the rotating knife blades. These rotating knives can be extremely dangerous...
6 6 high voltage use caution in high voltage areas. Do not assume the power to be off. (follow proper lockout procedures) safety precautions wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the oper...
7 7 7. Dull / damaged knives. Use only sharp, undamaged knives to avoid unnecessary kickback of the piece part. Dull and damaged knives will also affect cut quality. 8. Maximum cutting depth. The maximum cutting depth for one pass is 1/8” (3.2mm). Never set the machine to cut deeper than this in one...
8 8 25. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords. 26. Do not operate machine if under the influence of alcohol or drugs. Read warning labels on prescriptions. If there is any doubt, do not operate the machine. 27....
9 9 cleaning your machine may be shipped with a rustproof waxy oil coating and grease on the exposed unpainted metal surfaces. To remove this protective coating, use a degreaser or solvent cleaner. For a more thorough cleaning, some parts will occasionally have to be removed. Do not use acetone or b...
10 10 specifications cutting capacity (w x h) 18" x 9.5" (457 x 241mm) maximum depth of cut 5/16 ” (8mm) minimum material thickness 1/8 ” (3.2mm) cutterhead speed 5700 rpm min/max operating height .18”- 9.8” (5-250mm) table size 18” x 63” (460mm x 1600mm) variable feed drive 18-49.2 fpm (5.5-15m/min...
11 11 working zone and hazard zone.
12 12 technical features.
13 13.
14 14.
15 15.
16 16 machine operating conditions in a dry environment, at a temperature between 5°c and 40°c relative humidity: 30% ~ 95% rh. Dismantling and scrapping before dismantling the machine, disconnect all energy sources carefully. 1. Dismantling of electrical systems before disconnecting the cables from...
17 17 carrying and installation the machine's weight is about 2420 lbs (1100kgs) use lift truck to transport machine use gantry or crane to remove machine from pallet suction 1. Before the machine is started it must be connected to two suction hoods. 2. The hoses must be of a fire resistant type mat...
18 18 electrical connections 1. The connection of the machine to the main power must be carried out by a skilled electrician in accordance with the specifications of the standards in force. 2. Use the specific purpose tool in the toolbox (fig. 1), turn on the power control cabinet and introduce the ...
19 19 a separate electrical circuit should be used for your tools. If an extension cord is used, use only 3-wire extension cords, which have grounding type plugs and receptacles, which accept the tool’s plug. Before connecting the motor to the power line, make sure the switch is in the “off” positio...
20 20 check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that have grounding type plugs and receptacles that accept the tool’s plug. Repair or...
21 21 adjusting during initial running of the machine, the belts ride a little tighter in the pulley grooves and this can cause a slight reduction in belt tension. Adjust the tension after a few days of use, without over-tightening so as not to overload and cause consequent damage to the motor beari...
22 22 adjusting the tension and replacing the belts for feed.
23 23 adjusting the chains the drive chains stretch naturally due to play which occurs after a certain working period and must be tightened in order to ensure perfect operation and maximum torque drive to the movement..
24 24.
25 25 safety inspections check of emergency stop switch 1. Connect to power, start the cutterhead to make the machine run. 2. Push each emergency stop on machine and check if the cutterhead completely stops within 5 seconds. 3. When the emergency stop is pressed, the machine should not have any move...
26 26 control panel description of the panel.
27 27 operating the vfd-e description of the digital keypad 1. Status display display the driver's current status. 2. Led display indicates frequency, voltage, current, user defined units, and etc. 3. Potentiometer for master frequency setting. 4. Run key start ac drive operation. 5. Up and down key...
28 28 operation steps for the digital keypad.
29 29 starting and stopping the machine.
30 30
31 31.
32 32 thicknessing.
33 33.
34 34.
35 35 maintenance maintenance on your planer should be done at periodic intervals to ensure that the machine is in good working order. Inspection and maintenance should be performed at least twice a year but more often if the lathe receives constant use. Check daily for any unsafe conditions and fix...
36 36.
37 37.
38 38.
39 39 anti-reject arms the machine is equipped with a series of anti-reject arms which run continually as they pivot idly in relation to the supporting pin and operate with any thickness of wood, thus preventing the workpiece from being rejected in the direction of the operator and ensuring efficien...
40 40 troubleshooting problem probable cause remedy the machine does not start. 1. No voltage in line. Check voltage in line with instrument. 2. Fuses broken. Check fuses and replace if necessary 3. Emergency stop button pressed. Reset emergency button. 4. Main switch in position "0". Turn main swit...
41 41 notes.
42 42 baileigh industrial, inc. 1625 d ufek d rive m anitowoc , wi 54220 p hone : 920. 684. 4990 f ax : 920. 684. 3944 www . Baileighindustrial . Com baileigh industrial, inc. 1455 s. C ampus a venue o ntario , ca 91761 p hone : 920. 684. 4990 f ax : 920. 684. 3944 baileigh industrial ltd. U nit 1 f...