1. DL manuals
  2. Baileigh
  3. Sander
  4. OS-1414
  5. Operator's Manual

Baileigh OS-1414 Operator's Manual

Manual is about: OSCILLATING VERTICAL SPINDLE SANDER

Summary of OS-1414

  • Page 1

    Oscillating vertical spindle sander model: os-1414 © 2012 baileigh industrial, inc. Reproduction of this manual in any form without written approval of baileigh industrial, inc. Is prohibited. Baileigh industrial, inc. Does not assume and hereby disclaims any liability for any damage or loss caused ...

  • Page 2: Table of Contents

    Table of contents thank you & warranty .......................................................................................... 1 introduction ............................................................................................................ 3 general notes..................................

  • Page 3

    1 1 thank you & warranty thank you for your purchase of a machine from baileigh industrial. We hope that you find it productive and useful to you for a long time to come. Inspection & acceptance. Buyer shall inspect all goods within ten (10) days after receipt thereof. Buyer’s payment shall constitu...

  • Page 4

    2 2 force majuere. Seller shall not be responsible for any delay in the delivery of, or failure to deliver, goods due to causes beyond seller’s reasonable control including, without limitation, acts of god, acts of war or terrorism, enemy actions, hostilities, strikes, labor difficulties, embargoes,...

  • Page 5

    3 3 introduction the quality and reliability of the components assembled on a baileigh industrial machine guarantee near perfect functioning, free from problems, even under the most demanding working conditions. However if a situation arises, refer to the manual first. If a solution cannot be found,...

  • Page 6: Important

    4 4 learn to recognize safety information this is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury! Follow recommended precautions and safe operating practices. Understand signal words a signal word – danger, warning, ...

  • Page 7

    5 5 protect eyes wear safety glasses or suitable eye protection when working on or around machinery. Dust hazard wear appropriate dust mask. Dust created while using machinery can cause cancer, birth defects, and long term respiratory damage. Be aware of the dust hazards associated with all types of...

  • Page 8: Warning:

    6 6 protect against noise prolonged exposure to loud noise can cause impairment or loss of hearing. Wear suitable hearing protective devices such as ear muffs or earplugs to protect against objectionable or uncomfortable loud noises. High voltage use caution in high voltage areas. Do not assume the ...

  • Page 9

    7 7 safety precautions (cont.) 5. Remove any adjusting tools. Before operating the machine, make sure any adjusting tools have been removed. 6. Keep work area clean. Cluttered areas invite injuries. 7. Feed rate. Never jam a piece part against the sanding surface. This can cause the piece part to ki...

  • Page 10

    8 8 safety precautions (cont.) 20. Do not bypass or defeat any safety interlock systems. 21. Know the location of the on - off switch and the “e”- stop button. 22. Keep visitors a safe distance from the work area. 23. Keep children away. Children must never be allowed in the work area. Do not let th...

  • Page 11

    9 9 technical specifications table size (l x w) 14.6” x 4.6” (370 x 370mm) table tilt 0~45° spindle speed 1400rpm oscillations 24/min oscillation stroke .94” (24mm) sanding sleeve length 5.5” (141mm) maximum workpiece height 3.15” (80mm) dust port diameter 2” (50.8mm) motor .5 hp (0.37kw) 230v 60hz/...

  • Page 12

    10 10 getting to know your machine overall dimensions switch table insert sanding spindle table cabinet.

  • Page 13: Warning:

    11 11 installation important: maintain an adequate working area around the machine for safety. There should be 25” – 28” (635 – 710mm) in all directions around the machine. Have the work area well illuminated with proper lighting. Remove scrap and waste materials regularly, and make sure the work ar...

  • Page 14: Caution:

    12 12 electrical connection to electrical power should be made by a qualified electrician. Observe local electrical codes when connecting the machine. The motor should be protected with a time delay fuse or circuit breaker with a amperage rating slightly higher than the full load current of the moto...

  • Page 15: Caution:

    13 13 operation 1. Select spindle that is smaller than the curve to be sanded. 2. Use an insert plate that comes closest to the spindle without touching it. 3. Make sure that spindle is properly positioned in taper sleeve socket. With the wrench provided, tighten the nut. Note: never over tighten; i...

  • Page 16: Warning:

    14 14 tilting the table 1. Loosen the two table lock knobs (a), located under the table at both sides of the machine. 2. Tilt the table forward to the desired angle with your hands. 3. An angle scale is provided at the right side of the trunnion to indicate the degree of table tilt. 4. Tighten the t...

  • Page 17: Warning:

    15 15 selection guide for drum to table insert this machine is furnished with 10 drums. The range of drum diameter is from 1/4” to 4”. If the drum diameter is changed, the table insert needs to be changed to the proper size. The table below shows which table insert to use for various drum diameters....

  • Page 18: Warning:

    16 16 maintenance check daily for any unsafe conditions and fix immediately. Check that all nuts and bolts are properly tightened. On a weekly basis clean the machine and the area around it. To keep spindle sander in perfect condition, clean machine and attachments at all times. Clean tapered sleeve...

  • Page 19: Warning:

    17 17 troubleshooting trouble causes correction motor does not run when power switch is turned “on”. Switch is burned out. Connection wire is loose or damaged. Replace the switch. T ighten or replace the wire. Motor does not run at full speed. Power voltage is too low. 2. Motor is damaged. Test volt...

  • Page 20

    18 18 parts diagram 1.

  • Page 21

    19 19 parts diagram 2.

  • Page 22

    20 20 parts list item part no. Discription qty. 101 30201001g base 1 101a 30201001a top plate 1 102 w0000000 switch 1 103 s1006p1 strain relief 1 104 l000000 power cord 1 105 s0030622m philips head screw 4 106 10107098 rubber feet 4 107 s0210403 flat washer 7 108 s0011600m hex. Nut 4 109 s00303040 p...

  • Page 23

    21 21 item part no. Discription qty. 219 30202006p bracket 1 220 30202007p worm 1 221 s0010615m hex. Socket cap screw 4 222 30202008p shaft 1 223 30204010 crank shaft 2 224 s0230400 spring washer 4 225 s0400415 key 1 226 c1106001 bearing 2 227 s0521200 c ring 2 228 s0530028 c ring 2 229 s0230506 spr...

  • Page 24

    22 22 item part no. Discription qty. 321 s0030505m philips head screw 2 322 s0520027 c ring 1 323 30203008 5/8" sanding spindle 3 324 s0400550 key 1 331 30203015 2" rubber bushing 1 332 30203014 1-1/2" rubber bushing 1 334 30203017 1/2" sanding spindle 1 335 30203018 1/4" sanding spindle 1 337 30203...

  • Page 25

    23 23 notes.

  • Page 26

    24 24 notes.

  • Page 27

    25 25 notes.

  • Page 28

    26 26 baileigh industrial, inc. 1625 d ufek d rive m anitowoc , wi 54220 p hone : 920. 684. 4990 f ax : 920. 684. 3944 www . Baileighindustrial . Com baileigh industrial, inc. 1455 s. C ampus a venue o ntario , ca 91761 p hone : 920. 684. 4990 f ax : 920. 684. 3944 baileigh industrial ltd. U nit 1 f...