1. DL manuals
  2. Balt
  3. Indoor Furnishing
  4. 89843
  5. Assembly instructions manual

Balt 89843 Assembly instructions manual

Manual is about: Single Student Training Table W/Locking CPU Door

Summary of 89843

  • Page 1

    1 assembly instructions 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567...

  • Page 2: #89843   Lx-48B

    2 p-1 left side panel 1 ea p-2 right side panel 1 ea p-3 bottom panel 1 ea p-4 table top 1 ea p-5 top support 2 ea p-6 top front brace 1 ea p-7 bottom front brace 1 ea p-8 metal back panel 1 ea p-9 upper leg mount 1 ea p-10 lower leg mount 1 ea p-11 leg upright 1 ea p-12 metal panel 1 ea p-13 plasti...

  • Page 3: #89843

    3 l lock washer 1 ea m lock hex 1 ea n key 2 ea p door knob 1 ea r hinge 2 ea s grommet sleeve 2 ea t grommet cap 2 ea v allen wrench 1 ea part drawing description qty lx-48b workstation #89843 hardware list tools required: phillips head screwdriver standard flat head screwdriver p-14 keyboard brack...

  • Page 4

    4 place the left side panel (p-1) with the predrilled holes facing up and install 2 cam posts (d) in the 2 threaded insert nuts (pre-installed) as shown in illustration # 2. Install 2 cam locks (c) in the 2 large holes. Install 8 wood dowels (e) into the holes as shown in illustration # 2. Attach ma...

  • Page 5

    5 p-1 be sure that arrow on top of camlock (c) aligns with centerline of edge drilled hole. Phillips screwdriver centerline of edge drilled hole. Arrow p-3 c place the bottom panel (p-3) with the pre- drilled holes facing up and install 4 cam locks (c) in the 4 large holes as shown in illustration #...

  • Page 6

    6 17. To secure cam locks, insert large phillips head screwdriver and turn cam lock 1/4 turn (90 degrees) clockwise. Slide bottom panel (p-3) over the wood dowels (e) and the camposts (d) in the right side panel (p-2) as shown in illustration #6. Secure by turning the cam locks (c) 1/4 turn until th...

  • Page 7

    7 22.Attach back panel (p-8) to the left & right side panels (p-1 & p-2) using 4 screws (a9) as shown in illustration # 8. Place the table top (p-4) with the predrilled holes facing up and install 4 each cam posts (d) in the 4 threaded insert nuts (pre-installed) as shown in illustration # 9. Instal...

  • Page 8: 1-800-749-2258

    8 a3 p-15 p-15 p-14 a3 p-14 attach 2 keyboard brackets (p-14) to 1 keyboard slide (p-15) using 2 screws (a3) as shown in illustrations # 10. Attach 2 keyboard brackets (p-14`) to 2nd keyboard slide (p-15) using 2 screws (a3). Note: the 2 slides will have brackets on the opposite sides. P-14 30. 31. ...

  • Page 9

    9 illustration #12 p-4 b2 b2 b2 insert 1 grommet sleeve (s) in round opening in the left side panel (p-1) as shown in illustrations #12. Snap 1 grommet cap (t) into grommet sleeves (s) . 34. 35. T s p-1 p-13 attach metal panel (p-12) to the left leg assembly using 2 phillips screws (a1) as shown in ...

  • Page 10: Important

    10 the balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal use due to defect or imperfection, the defective part or product will be replaced. Dama...