Bang & Olufsen BeoLink Wireless 1 Manual
Summary of BeoLink Wireless 1
Page 1
Beolink wireless 1 guide.
Page 2
Warning: to reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment. To completely disconnect this equipment from the ...
Page 3
Introduction, 4 this chapter provides you with an overview of the wireless 1 system in the main room and the link room and describes the master link and power link setups. Close-up operation, 6 find out how to switch on the timer play function and ‘listen in’ on a source playing on the main room sys...
Page 4
Introduction master link setup if your link room product is either an audio or a video system, it must be connected to beolink wireless 1 with a master link cable. For operation of such a setup, refer to the guide enclosed with your link room product. Note that a beolab 3500 setup must also be conne...
Page 5
Power link setup if your link room product is a pair of active speakers, they must be connected to beolink wireless 1 with power link cables. This setup also requires an ‘ir-eye’, in order to be able to operate the the system – either by close-up operation, or with a bang & olufsen remote control. F...
Page 6
Close-up operation this page concerns only a power link setup with an ‘ir-eye’. For information about close-up operation of link room products set up with master link cables, refer to the guides enclosed with the products. The small circular ‘ir-eye’ has buttons for close-up operation. You can use t...
Page 7
Beo4 remote control this page concerns only a power link setup with an ‘ir-eye’. For information about beo4 remote control operation of link room products set up with master link cables, refer to the guides enclosed with the products. With the beo4 remote control you can switch on the sources from y...
Page 8
This page concerns only a power link setup with an ‘ir-eye’. For information about sound adjustments of link room products in master link setups, refer to the guides enclosed with the products. With the beo4 remote control you can adjust the sound coming out of the link room speakers. All sound leve...
Page 9
Set up beolink wireless 1 on the next pages is explained how to install a set of beolink wireless 1 – both in the main room and in a link room. We recommend that you follow this procedure: – set up connection between the wireless 1 units as explained on p. 10. – make the cable connections as explain...
Page 10
Wireless 1 – transmitter/ receiver … wireless 1 must be set up as either transmitter or receiver. Before fastening the transmitter and receiver to the wall, you must establish connection between them. This must be done while the units are located in the same room. The connection procedure described ...
Page 11
Wireless 1 – wall mount wireless 1 can be fastened to a wall (or ceiling) with one of the two enclosed brackets – in either a horisontal or a vertical position. It can be placed on the bracket so that the cables may be run either to the left or to the right. However, if you place wireless 1 vertical...
Page 12
>> set up beolink wireless 1 connections – master link in the main room: connect the transmitter to the master link socket on the main system. Then connect both the main system and transmitter to the mains supply. In the link room: connect the audio or video product to the master link socket on the ...
Page 13
Connections – power link in the main room: connect the transmitter to the master link socket on the main system. Then connect both the main system and transmitter to the mains supply. In the link room: connect the loudspeakers to the power link sockets on the receiver. Connect the ‘ir-eye’ to the so...
Page 14
‘ir-eye’ – cable connections the small circular ‘ir-eye’ is available from a bang & olufsen retailer. An ‘ir-eye’ must be used in each link room with a power link setup. Use the cable supplied with the ‘ir-eye’ and connect it as explained here: > cut the cable to the required length (from the receiv...
Page 15
‘ir-eye’ – wall mount if the ‘ir-eye’ is placed next to a door and at a suitable height, you can easily switch on or off by close- up operation when entering or leaving the room. Likewise, if it is placed near your telephone, you can switch off the speakers while you are on the phone. > use the wall...
Page 16
Option settings when you have made all the connections as described on the previous pages or in the guides enclosed with your link room products, you may start to use the system. However, in order for your setup to function properly, you must option program your link room products. On this page you ...
Page 17
Use a beo4 remote control to set the option. The entire system must be switched to standby: > while holding down the • button, press list. > let go of both buttons. > press list repeatedly until option? Is shown in the beo4 display, and press go. > press list repeatedly until l.Opt is shown in the b...
Page 18
The european parliament and the council of the european union have issued the waste electrical and electronic equipment directive. The purpose of the directive is the prevention of waste of electrical and electronic equipment, and to promote the reuse and recycling and other forms of recovery of suc...
Page 19
This product is in conformity with the provisions of the directives 1999/5/ec and 2006/95/ec. This product may be used in member states of the eeu and efta. Technical specifications, features and the use thereof are subject to change without notice! 19.
Page 20
3509535 0703 www.Bang-olufsen.Com.