- DL manuals
- Banner American
- Laminator
- BA-EN45
- Operating Instructions Manual
Banner American BA-EN45 Operating Instructions Manual
Summary of BA-EN45
Page 1
Operating instructions entry 4500 model no. Ba-en45 banner american products, inc. Temecula, ca.
Page 2: Caution...
Caution... To avoid any damage, please do not use razors or sharp objects near the rollers..
Page 3
Table of contents i. For your safety ..................................................... 2 ii. Electrical safeguards ........................................... 2-3 iii. Specifications ........................................................ 3 iv. Set-up ..............................................
Page 4
Entry 4500 (ba-en45) mandrel.
Page 5
U do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient location for future reference. U read all safety messages located in this instruction manual and on the laminator very care- fully. U...
Page 6
U do not operate the laminator with a damaged power supply cord or plug. U replace fuses only with same type rated 30a, 240v and 1a, 250v fuses. Contact your dealer for replacement fuses. U there are two (2) emergency stop buttons on your entry 4500, one on each side. Depressing one of these buttons...
Page 7
Bottom roll: with the gripper spring towards you, push the core gripper blade away from you and place the roll of film onto the mandrel so that the film unwinds away from you from the bottom of the roll. Turn the roll on the mandrel to lock the core gripper blade into the cardboard film core. Bottom...
Page 8
8.Turn the speed control knob far enough to allow the rollers to sufficiently pull the poster board into the laminator. Keep in mind that varying films, media, and temperatures will require different speeds. 9. Feed the poster board between the rollers. 10. After the laminator is properly threaded a...
Page 9
Rewind option for pressure sensitive laminating....
Page 10
Vi. Pressure sensitive laminating... Note: you must have the rewind option for pressure sensitive films in order to laminate with pressure sensitive material. 1. Load a roll of pressure sensitive film onto the supply mandrel so that it unwinds toward you from the bottom of the roll. 2. Load an empty...
Page 11
1. Load a roll of adhesive, with the liner wound to the outside, onto the top mandrel in the same manner as with laminating film. 2. Load a roll of paper on the bottom mandrel or use adhesive the same width as the mount board to keep the adhesive from accumulating on the rollers. 3. Place mount pins...
Page 12
Ix. Maintenance/service... Always use caution when servicing your laminator. Precautions: disconnect the power supply and open the panel breaker before attempting to service or repair the laminator. Any maintenance or service should be preformed only by those having appropriate technical training an...
Page 13
3. Open the roller release handle on the side of the laminator and pull the film out of the unit that has become wrapped around the rollers. 4. If you have a severe wrap-around, it may be necessary to use the reverse feature to back the film out. Be sure to pull the film away from the laminator. If ...
Page 14
Do’s and don’ts... Read the instruction manual before operating your laminator. Always run test samples before laminating valuable items. Feed the print through slowly and evenly, smoothing it as it is pulled into the laminator. Operate the laminator with two rolls of the same width laminating film ...
Page 15
Xiii. Parts list and illustrations t his section contains reference drawings and a parts list to assist you when ordering parts for your laminator. The drawings show only those parts that may be replaced by the dealer. Item part number description quantity 1 11108 bar, cam pressure 2 2 11109 bracket...
Page 16
Item part number description quantity 61 557 knob, thermostat 2 62 11045 variable speed control 1 63 4096 clamp, power cord 1 64 2379 main body brake for rl43 4 66 2378 brake nut for rl43 4 67 2777 switch, journal, emergenc 2 68 11100 capacitor, .01uf 1 69 3032 holder, supply mandrel t 2 70 3033 hol...
Page 17
Exploded assembly 1 3.