- DL manuals
- Banner American
- Laminator
- BA-FS27
- Instructions Manual
Banner American BA-FS27 Instructions Manual
Summary of BA-FS27
Page 1
Operating instructions finisher 2700 model no. Ba-fs27 banner american products, inc. Abcoffice 800-658-8788 www.Abcoffice.Com.
Page 2: Abcoffice
Table of contents i. Get to know your laminator ........................... 1-2 ii. For your safety ............................................... 3 iii. Electrical safeguards ....................................... 3-4 iv. Specifications .................................................. 4 v. Set-...
Page 3: Abcoffice
Forward reverse upper mandrel upper supply mandrel holder emergency stop button lower mandrel upper idler bar safety shield tie bar lower supply mandrel holder feed table guide emergency stop button feed table lower idler bar right control panel (see below) left control panel (see below) motor heate...
Page 4: Abcoffice
Roller pressure adjustment to open the rollers: pull out the pin and turn handle clockwise until it will not turn any farther and the pin locks into place. To mount: from the open position, pull out the pin and turn handle counter-clockwise until pin locks into place. The front pressure adjustment h...
Page 5: Abcoffice
U do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient location for future reference. U read all safety messages located in this instruction manual and on the laminator very care- fully. U...
Page 6: Abcoffice
U do not operate the laminator with a damaged power supply cord or plug. U replace fuses only with same type rated 30a, 240v and 1a, 250v fuses. Contact your dealer for replacement fuses. U there are two (2) emergency stop buttons on your finisher 2700. Pressing either one of these buttons will stop...
Page 7: Abcoffice
Feed table installation: slide the feed table over the front and rear feed table holders. (the feed table weighs about 15 lbs.) loading film onto mandrels the following instructions apply to poly-in film rolls as they would appear from the front of the laminator. Top roll: hold the core gripper to t...
Page 8: Abcoffice
Mandrel tension adjustment mandrel tension must be set correctly to ensure good lamination quality. Adjust the tension by turning the knurled knobs at both ends of the mandrels. To tighten the tension, turn the knobs clockwise. To loosen the tension, turn the knobs counterclockwise. Adjust only 1/8 ...
Page 9: Abcoffice
Vi. Thermal laminating... 1. Be sure all laminator parts (i.E. Safety shield, feed table, etc.) are in their proper positions and the laminating film is loaded correctly (see page 3 for film loading instructions). 2. Select the close position using the pressure control handle located on the right si...
Page 10: Abcoffice
7. Set the forward/reverse switch to the forward position. 8. Turn the motor control on/off switch to the on position. 9. Turn the motor control knob far enough to sufficiently pull a feed card into the laminator. 10. Feed the feed card between the rollershoes™ and into the front rollers. 11. After ...
Page 11: Abcoffice
Caution: heated rollers are for warm-up only and should be turned off when operating temp- erature is reached to avoid damaging the rollers. 4. Set the temperatures according to the film manufacturer’s recommendations for the film you have chosen. The finisher 2700 will take approximately 15 minutes...
Page 12: Abcoffice
Cleaning rollershoes™: clean the rollershoes™ periodically to avoid adhesive build-up. Build-up can inhibit the film from moving over the shoes smoothly. Use the following procedure to clean the rollershoes™. 1. Turn the heated rollers and top & bottom heat switches off and allow the laminator to co...
Page 13: Abcoffice
Laminated item curls top or bottom film tension loosen tension on side (top is too high or bottom) that is curling up laminated item is wrinkled mandrel tension too loose increase mandrel tension on side (top or bottom) that has wrinkles temperature too high reduce temperature moisture in paper bein...
Page 14: Abcoffice
Xiii. Warranty & return policy... Warranty: your finisher 2700 is warranted to be free of defects in material and workmanship for a period of 1 year from the date of original purchase. In the event of a defect in materials or workmanship, banner american products, inc. Or its authorized dealer, will...