Uv-3r faq an amazing user community collaboration project. Uv-3r faq v. 2012-01-27 page 1.
Quick troubleshooting general what is the baofeng uv-3r? What is the baofeng uv-3r mark ii and uv-x4? How much does the uv-3r cost? Where can i buy the uv-3r and accessories? What warranty is offered? How long does it take to get it (from hong kong)? What is in the uv-3r box? What are the difference...
How does the led torch work? What is the transmit frequency range? What is wide/narrow setting? What does relaym do? What does the save function do? How can i do “reverse” on a repeater? How do i generate dtmf tones? How do i set frequency scan limits? Squelch settings can i use the uv-3r while the ...
Quick troubleshooting problem quick solution in the faq? Programming software does not connect to the radio push the cable harder into the radio check the proper com port has been selected (com5 seems to work) tx lock on vhf it is a known problem when using high power on vhf with the supplied earpie...
For use with amateur fm satellites. Further, the transceiver contains a listen-only fm receiver for the fm broadcast band on a dedicated chip. (*) the transceiver is 47x81x23 mm, and weights about 120g (radio with battery and antenna). That’s about the same size as a standard 20 cigarette pack, whic...
You may want to order it with the usb programming cable. The software is a free download. What warranty is offered? If buying directly from hong kong you should get a repair/replacement upon return of the faulty item. You have to pay for the shipping cost for returning the faulty item to hk. Check t...
What are the differences between the uv-3r mk.I, uv- 3r mk.Ii, uv-x4, uv-100 and uv-200? The uv-3r mk.I, uv-100 and uv-200 models are said to be electrically identical, just with a different exterior look and external port. Uv-100 and uv-200 share a compatibility with speaker- mic (409shop item 41-7...
Green shell too, which produces a tri-tone camo. After tests the paint was found to be quite resilient to damage. Thanks to nuno for the tests and the following photos: http://groups.Yahoo.Com/group/uv-3r/photos/album/297298078/pic/list is there a replacement type for the battery? The battery pack i...
Or cables. A pl-to-sma works too, but it might put too much strain on the antenna connector. Some of the adapters are a tight fit, and it may be necessary to remove a small amount from the case near the led with a hobby knife to get firm seating. Which dual-band antenna can i buy? Not all sma-male a...
● shift value for transmit. Usually 600 khz for 2 meters, 1.6 or 5 mhz for 70 cm. Make sure you are in vfo mode for 2 meters. Display should show no channel number. In case, press/hold u/v key long enough to get there -- it will cycle through memory mode, uhf, vhf. To set the receive frequency, lift...
First, get a list of the repeaters or simplex frequencies you wish to program into the baofeng. In addition, you will need: ● a programming cable - usb connector on one end, the four-conductor plug on the other end. Yaesu programming cords will not work, as the connections are different. ● programmi...
Frequencies (if allowed). When you are done, exit the program and disconnect the cable from the computer and the ht. Please turn the radio off before inserting or removing the programming cable and save yourself the possibility of doing some harm to them. Once basic programming is done with baofeng ...
So, you are waiting for your “r” and programming cable to hit your doormat but you have free time to prepare the memory file? No worries, install the correct software package on your computer, type in all your memories and save to a local file. Once the radio+cable arrives, install proper drivers (f...
Name=0 to name=1 when you reload the uv3r software you can enter the name of the channel (4 characters only) in the last column. The bad news is that it's not yet clear how we should enable the channel name (alpha tag) display on the radio itself; nb: the change in settings.Ini file must be done whe...
4 145.880 435.145 5 145.880 435.140 during a pass change the receiver frequency as the rx signal shifts out of the channel: aos mem 1 -> mem 2 -> tca (center) mem 3 -> mem 4 -> mem 5 los the currently (26 january 2012) active satellites: ao-27, so-50. Note that ao-51, whose frequencies have been use...
Folder for earlier versions or those for mk-i radios. The preferred software for updating the channel memory is chirp, available from the program originators site http://chirp.Danplanet.Com/ . There are windows, mac (using kk7ds python runtime) and two ‘flavors’ of linux versions (fedora, ubuntu) av...
Baofeng software uv-[nn] (where [nn] = 3r or x4) has these although listed differently such as duplex/offset as separate entries for rx/tx freq sets. In addition uv-nn includes setting the basic setup items like freq range, scan setups, vco setup for both uhf and vhf vco's (rx freq, tx freq, encode,...
You can save that as the basic setup in chirp. Then you enter your memory frequencies, offsets, tones etc., save that file under an appropriate filename, and then upload to the radio. You now have all of your setup info and basic radio preferences saved along with the memory channel assignments. Thi...
You ought to get a pop-up box from which you can choose the port as something like '/dev/ cu.Usbserial' - this is the port that is hidden until the pl2303 driver is installed; other options for port are bluetooth ports on my setup. Choose vendor as baofeng, model as uv-3r, and hopefully hitting ok w...
This works fine for ubuntu, however in fedora the linux usb serial device has to be made rwc to be operational in wine. To make the linux usb serial device rwc, you could execute "sudo chmod 777 /dev/ttyusb0" in a linux terminal. With debian it works fine with a tty cable and wine ---- both versions...
What is wide/narrow setting? This setting controls rx bandwidth and fm deviation. These have been measured to be: tx, max deviation wide, +/- 4.8khz tx, max deviation narrow, +/- 2.4khz apparent rx -6db bandwidth wide +/- 8khz apparent rx -6db bandwidth narrow +/- 4khz adjacent channel selectivity m...
Region 2 - americas - and 12.5 khz in iaru region 1 - eu/africa -) and run a memory scan instead. The third option is to set the band limits as per instructions in message number 2968 , but that limits all frequency related programming. This is not an elegant option, a good used scanner works much b...
Chirp is a free cross-platform, cross-radio programming tool. It works on windows and linux (and macosx with a little work). It supports a growing list of radios across several manufacturers and allows transferring of memory contents between them. Mike n4mep tells how: i used chirp to read all my st...
Many uv-3rs users experience a very low power output on the vhf ham band in “low” setting. It has been measured to be at around 100mw at 145 mhz instead of the advertised 1w. This behavior is normal. Sp3swj has found a hardware fix for this - replace inductor l19 with 220nh. This will then give 1.3w...
- remove the nut from the rotary encoder. - remove the four screws holding the circuit board: there two near the lower-middle of the board and also two just above the display. - with the display face-up, there is a solder connection to the sma connector near the connector itself on the circuit board...
Increased up to 27k or 33k. For the tone beeps path r10 (100k) can be replaced by 220k or greater. However, the 1750hz tone, which is used for accessing repeaters, is sent via the loudspeaker and picked up by the microphone. If r10 is increased too much the level of this access tone sent by the mic ...
● tune uv-3r to the frequency located few steps above ● make sure sql/squelch is set to one ● make sure no ctcss/dcs are set ● switch uv-3r off ● open up the uv-3r as described elsewhere; ● solder about 10cm of wire in place of the antenna connector ● connect the earpiece ● connect the charger to uv...
If no fm broadcast can be received, try the procedure described above for looking for cold solder joints. How to extend frequency range? The frequency range of the two bands can be extended using the official programming software and the programming cable. It is a trial and error procedure which mig...
Only one pair of ranges will be written to the radio. Save the settings.Ini file and close the text editor program. Now re-open the uv-3r program. Make sure you are opening the same version of which you have edited the settings file, in case you have several installs on your pc. The new range will b...
Is there a software maintenance mode? As of uv-3r sold until january 2012 (mark i and mark ii) there is no software maintenance mode. If it is there, nobody has figured out how. My uv-3r just completely reset itself. Why? If the frequency on the display was outside the normal range, e.G. 133mhz, whe...
The program or are located in eeprom on the processor itself and aren't readily available with the supplied program - unless there's a "calibration menu" available that can be brought up in the radio that i don't know about... From what i can tell, the only on-board adjustment is frequency trimming:...
Clicked on ok and program began writing to radio. Upon completion the dddd25 disappeared from the first and second lines of the display. My display now shows 146.0000 on first line and 440.0000 on second line. 10) i clicked on program on top line of grid and selected "read from radio". Got dialogue ...
Available on the fcc site (link below in licensing section). Licensing issues information provided here is informative and is not intended as legal advice. Note that some sellers (such as dealextreme) carry these radios with no mention of the licenses required to operate (or in some cases even posse...
These units can operate on frs/gmrs frequencies. They can probably be configured for fm devition within the allowed limits for these bands. Frs/gmrs radios are required to be fcc type accepted for frs/gmrs use; these are not. Frs radios are prohibited from having detachable antennas (in order to pre...
Frs/gprs/fire/police/marine/aviation/sar or any other non-ham bands, even with a valid operators license for those bands/frequencies is generally illegal except for the bare minimum of communications required in a life threatening communication when no other options are available. See the sections a...
This frequently asked questions document was started on 13 september 2011 after a relatively large amount of repeating questions on the uv-3r yahoo group mailing-list. A document on google docs platform was created and the web url posted to the list. Anyone knowing the link was able to modify the co...
Ondra, ok1cdj, czech republic, jo70va mark, ki4bsz, usa bart van allen, ka7zfd, utah, usa uv-3r faq v. 2012-01-27 page 37.