Baquapure HIGH RATE SAND FILTER Owner's Manual
OWNER’S MANUAL
H I G H R AT E S A N D F I LT E R
T
ROUBLE
S
HOOTING
WARNING: NEVER RUN PUMP WITH SLICE VALVE CLOSED!
WARNING: NEVER CHANGE VALVE POSITION WITH PUMP RUNNING!
CCSS 5000DX W
ATER
P
OLISHER
U
SE
Warning: To reduce the risk of injury and product damage when using optional polishers:
• Never use any chemicals or components other than as recommended
• Never mix chemicals.
• Always wear protection for eyes, skin and clothing.
• Do Not Smoke. Avoid sparks and open Flames.
• Turn off pump and close valves before installing or servicing water polisher.
W
INTERIZATION
1. Backwash filter system completely. See Cleaning Instructions.
2. Run a filter cleaning chemical through filter system as per cleaner instructions.
3. Turn pump off. Disconnect hoses from skimmer and return fitting.
4. Remove drain plug cap from bottom of filter tank. Do Not remove hex drain assembly, #28.
5. Unscrew drain plugs located at bottom of pump trap and front of pump housing. Let water drain completely.
6. Disconnect filter to pump connection. Loosen union connection on discharge of pump and remove from pump. Do Not lose 2
″
union gasket. Lift and remove pump and pump base from filter base. Store inside.
Limited Warranty:
Leisure Bay manufactures its products and equipment in accordance with very high standards of
workmanship. We use the best materials available and maintain the highest quality procedures practical
in the industry. In accordance, Leisure Bay warrants its products as follows: Warranty only applies to
OEM’s and Distributor’s of Waterway.
All parts manufactured by Leisure Bay will be replaced or repaired of the defects as determined by
Leisure Bay for a period of THREE YEARS from the date of purchase. The warranty does not cover O-
rings, pressure gauges, pump seals or any other parts not manufactured by Leisure Bay.
Baquapure pumps are covered by a limited warranty from any defects in material or workmanship for a
period of THREE YEARS from the date of purchase. This warranty includes the motor but excludes the
motor seal.
All rotational molded sand filter bodies have a warranty of TEN YEARS, warranted on a pro-rated basis.
If a defect becomes apparent during the first three (3) years, the body will be exchanged for a new body
if the defects are determined by Leisure Bay to be the responsibility of Leisure Bay. If a defect becomes
apparent after three (3) years from the date of purchase and in the opinion of Leisure Bay will require
\replacement, the body will be exchanged on an adjusted on a pro-rated basis. Charges to the owner,
based on a pro-rated basis will be determined by the actual number of months installed beginning with
the date of purchase.
Products that fail or become defective during the warranty period, except as a result of improper instal-
lation, bad water chemistry, accidents or negligence on behalf of the owner, freezing, earthquake, fire,
floods, or any other acts of nature, shall be repaired or replaced at Leisure Bay option without charge to
the owner. This process will be completed within 90 days of receipt of the defective product barring
delays caused by the acquisition of component parts not manufactured at our facility.
To obtain warranty replacements or repair, defective products should be returned (transportation paid)
to the place of purchase or to Leisure Bay. It should include a description of the defect and the
circumstances surrounding the incident or problem.
Warranty begins on the date of purchase. Leisure Bay shall not be responsible for cartage, removal and/or
installation or any other costs incurred in obtaining warranty replacements.
This warranty gives you specific legal rights. You may also have other rights which vary from state
to state.
M
OTOR
D
OES
N
OT
S
TART
:
Make sure motor is plugged in.
Circuit breaker in OFF position.
Thermal Overload in tripped position.
Wiring installation incorrect.
Incorrect line voltage.
Defective wiring.
T
HERMAL
O
VERLOAD
T
RIPS
:
Low Voltage.
Wiring installation incorrect.
Dual voltage pumps mis-wired.
Inadequate ventilation.
N
O
W
ATER
F
LOW
:
Obstruction of suction or return line.
Clogged impeller.
Suction system air leaks.
Slice Valve Closed.
Clogged Hose Fitting.
Clogged Basket.
Dirty Sand.
E
XCESSIVE
P
UMP
N
OISE
:
Worn Bearings.
Suction Line Clogged.
Pump incorrectly mounted.
Hose Fitting partially closed.
Slice Valve partially closed.
Clogged Trap Basket.
I
NADEQUATE
F
ILTERING
:
Sand level too low.
Inadequately cleaned system.
Excessive dirt load.
Chemical imbalance.
Inadequate system pressure.
WATERWAY PLASTICS 2200 EAST STURGIS RD. OXNARD, CA 93030
111402 810-0081-LB R8