1. DL manuals
  2. Baracoda
  3. Barcode Reader
  4. BRR-L
  5. Programming Manual

Baracoda BRR-L Programming Manual - 1 Introduction

Other manuals for BRR-L: Programming Manual
Manual is about: Baracoda Barcode Reader User Manual

Summary of BRR-L

  • Page 1

    Nextel roadrunners scanner (brr-l) by baracoda programming guide.

  • Page 3

    Nextel roadrunners scanner programming guide last updated: 10/14/05 i © baracoda 2005 nextel roadrunners scanner (brr-l) programming guide contents 1 introduction.............................................................................................................................................

  • Page 5: 1 Introduction

    Nextel roadrunners scanner programming guide last updated: 10/14/05 1 © baracoda 2005 1 introduction this manual contains the necessary barcodes to configure the parameters of your scanner. You can either print out this document to scan its barcodes or in some cases you can even scan the barcodes ri...

  • Page 6: 2 General Configuration

    Nextel roadrunners scanner programming guide last updated: 10/14/05 2 © baracoda 2005 2 general configuration 2.1 reset default settings: reading the "default settings” label resets all scanner parameters to the default factory settings and switches it off. Caution: scanning this barcode will reset ...

  • Page 7

    Nextel roadrunners scanner programming guide last updated: 10/14/05 3 © baracoda 2005 switch on delay: 2 seconds switch on delay: 0 second (*) \ v t \ v t z \ n u l \ s o h \ e t x \ f f \ f f s wi t ch on del ay : 2 s ecs \ v t \ v t z \ n u l \ s o h \ s o h \ f f \ f f s wi t ch on del ay : 0 s e...

  • Page 8

    Nextel roadrunners scanner programming guide last updated: 10/14/05 4 © baracoda 2005 programming procedure for “set timestamp” option set timestamp “end of config” \ v t \ v t \ f n c 4 t \ n u l \ n u l \ l f \ l f set ti mes t amp \ l f \ l f e n d \ f f \ f f end of conf i g note: the timestamp ...

  • Page 9

    Nextel roadrunners scanner programming guide last updated: 10/14/05 5 © baracoda 2005 for example, to set the current time at may 16, 2007 3.25 p.M., the user will scan the following sequence: - “set timestamp” label, - “0” label, - “7” label, - “0” label, - “5” label, - “1” label, - “6” label, - “1...

  • Page 10

    Nextel roadrunners scanner programming guide last updated: 10/14/05 6 © baracoda 2005 an important reminder: if an acknowledgement (ack) beep or storage of codes in memory is needed, the scanner must first be set to “no data loss mode” (see section 2.3). Caution: scanning any of the following three ...

  • Page 11

    Nextel roadrunners scanner programming guide last updated: 10/14/05 7 © baracoda 2005 batch mode . Places the scanner in batch mode. Caution: scanning this barcode erases all codes in memory. \ v t \ v t d \ n u l \ s o h \ s o h \ f f \ f f bat c h discharge barcode. Caution: scanning this barcode ...

  • Page 12

    Nextel roadrunners scanner programming guide last updated: 10/14/05 8 © baracoda 2005 beep level volume = low beep evel volume = high \ v t \ v t \ f n c 4 \ d c 4 \ n u l \ s o h \ f n c 4 @\ f f \ f f beep l ev el : l ow \ v t \ v t \ f n c 4 \ d c 4 \ n u l \ s o h \ f n c 4 a \ f f \ f f beep l ...

  • Page 13

    Nextel roadrunners scanner programming guide last updated: 10/14/05 9 © baracoda 2005 security (pin code) settings the initial pin code can be disabled or enabled by scanning the following barcodes: disable bt security code enable bt security code (*) \ v t \ v t ^ \ n u l \ s t x ! \ n u l \ f f \ ...

  • Page 14

    Nextel roadrunners scanner programming guide last updated: 10/14/05 10 © baracoda 2005 programming procedure for “set suffix (prefix)” option. *= max suffix (prefix) length is 32 characters set timestamp “end of config” \ v t \ v t \ f n c 4 t \ n u l \ n u l \ l f \ l f set ti mes t amp \ l f \ l f...

  • Page 15: 3 Symbology Settings

    Nextel roadrunners scanner programming guide last updated: 10/14/05 11 © baracoda 2005 3 symbology settings 3.1 symbology default settings sets the default decoder settings for all the symbologies. Set decoder default settings \ v t \ v t \ f n c 4 ~ \ n u l \ e t x a c \ n u l \ f f \ f f set dec o...

  • Page 16

    Nextel roadrunners scanner programming guide last updated: 10/14/05 12 © baracoda 2005 3.3 disable all symbologies even if all symbologies are disabled, the roadrunners scanner will still be able to read the programming barcodes included in this document. Caution: care should be used when disabling ...

  • Page 17

    Nextel roadrunners scanner programming guide last updated: 10/14/05 13 © baracoda 2005 3.4 codabar settings codabar - not active codabar – active (*) \ v t \ v t \ f n c 4 ~ \ n u l \ e o t f d \ s o h b \ f f \ f f di s abl e codabar \ v t \ v t \ f n c 4 ~ \ n u l \ e o t f d \ s o h a \ f f \ f f...

  • Page 18

    Nextel roadrunners scanner programming guide last updated: 10/14/05 14 © baracoda 2005 3.5 code 11 settings code 11 - not active (*) code 11 - check digits - checked and transmitted (*) \ v t \ v t \ f n c 4 ~ \ n u l \ e o t j d \ s o h b \ f f \ f f di s abl e code11 \ v t \ v t \ f n c 4 ~ \ n u ...

  • Page 19

    Nextel roadrunners scanner programming guide last updated: 10/14/05 15 © baracoda 2005 3.6 code 39 settings code 39 - active (*) code 39 - start/stop - not transmitted (*) \ v t \ v t \ f n c 4 ~ \ n u l \ e o t e d \ s o h a \ f f \ f f enabl e code39 \ v t \ v t \ f n c 4 ~ \ n u l \ e o t e d \ s...

  • Page 20

    Nextel roadrunners scanner programming guide last updated: 10/14/05 16 © baracoda 2005 3.7 code 128 settings code 128 / ean 128 - not active code 128 / ean 128 - barcode length - any length (*) \ v t \ v t \ f n c 4 ~ \ n u l \ e o t c d \ s o h b \ f f \ f f di s abl e code128 \ v t \ v t \ f n c 4...

  • Page 21

    Nextel roadrunners scanner programming guide last updated: 10/14/05 17 © baracoda 2005 3.9 interleaved 2 of 5 settings interleaved 2 of 5 - not active interleaved 2 of 5 - check digit - mod 10 - checked but not transmitted \ v t \ v t \ f n c 4 ~ \ n u l \ e o t g d \ s o h b \ f f \ f f di s abl e ...

  • Page 22

    Nextel roadrunners scanner programming guide last updated: 10/14/05 18 © baracoda 2005 3.10 msi code settings msi code - not active (*) msi code - check digit - double mod 10 - checked and transmitted \ v t \ v t \ f n c 4 ~ \ n u l \ e o t k d \ s o h b \ f f \ f f di s abl e msi \ v t \ v t \ f n ...

  • Page 23

    Nextel roadrunners scanner programming guide last updated: 10/14/05 19 © baracoda 2005 3.11 standard 2 of 5 settings standard 2 of 5 - not active standard 2 of 5 - barcode length - any length \ v t \ v t \ f n c 4 ~ \ n u l \ e o t h d \ s o h b \ f f \ f f di s abl e standard 2 of 5 \ v t \ v t \ f...

  • Page 24

    Nextel roadrunners scanner programming guide last updated: 10/14/05 20 © baracoda 2005 3.12 upc/ ean settings upc / ean - active (*) upc / ean - not active \ v t \ v t \ f n c 4 ~ \ n u l \ e o t d d \ s o h f \ f f \ f f enabl e ean/ upc \ v t \ v t \ f n c 4 ~ \ n u l \ e o t d d \ s o h g \ f f \...

  • Page 25

    Nextel roadrunners scanner programming guide last updated: 10/14/05 21 © baracoda 2005 upc / ean - check digit - upc-e - transmitted (*) upc / ean - check digit - ean-8 - transmitted (*) \ v t \ v t \ f n c 4 ~ \ n u l \ e o t l d \ s o h g \ f f \ f f enabl e upce c hec k di gi t t r ans mi s s i o...

  • Page 26

    Nextel roadrunners scanner programming guide last updated: 10/14/05 22 © baracoda 2005 3.13 set min or max length option the procedure to be followed for each barcode is shown below: read "start - set min (max) length" label start read intermediary label corresponding to the next digit of the min (m...

  • Page 27

    Nextel roadrunners scanner programming guide last updated: 10/14/05 23 © baracoda 2005 \ v t \ v t \ f n c 4 ~ \ n u l \ s t x \ l f \ l f s et mi n l engt h start – set min length \ v t \ v t \ f n c 4 ~ \ n u l \ e t x \ l f \ l f s et max l engt h start – set max length \ l f \ l f e n d \ f f \ ...

  • Page 28: Appendix 1: Symbology Table

    Nextel roadrunners scanner programming guide last updated: 10/14/05 24 © baracoda 2005 appendix 1: symbology table header selected symbology header selected symbology select all \ l f \ l f a \ l f \ l f interleaved 2 of 5 \ l f \ l f g \ l f \ l f code 93 \ l f \ l f b \ l f \ l f standard 2 of 5 (...

  • Page 29: Characters)

    Nextel roadrunners scanner programming guide last updated: 10/14/05 25 © baracoda 2005 appendix 2: ascii table (a-z, a-z, 0-9, punctuation, control characters) upper case letters (a-z): name programming bar code name programming bar code a \ l f \ l f a \ l f \ l f n \ l f \ l f n \ l f \ l f b \ l ...

  • Page 30

    Nextel roadrunners scanner programming guide last updated: 10/14/05 26 © baracoda 2005 lower case letters (a-z): name programming bar code name programming bar code a \ l f \ l f a \ l f \ l f n \ l f \ l f n \ l f \ l f b \ l f \ l f b \ l f \ l f o \ l f \ l f o \ l f \ l f c \ l f \ l f c \ l f \...

  • Page 31

    Nextel roadrunners scanner programming guide last updated: 10/14/05 27 © baracoda 2005 punctuation: name programming bar code name programming bar code space \ l f \ l f \ l f \ l f space : \ l f \ l f : \ l f \ l f : ! \ l f \ l f ! \ l f \ l f ! ; \ l f \ l f ; \ l f \ l f ; " \ l f \ l f " \ l f ...

  • Page 32

    Nextel roadrunners scanner programming guide last updated: 10/14/05 28 © baracoda 2005 decimal numbers (0-9): number programming bar code number programming bar code 0 \ l f \ l f 0 \ l f \ l f 0 5 \ l f \ l f 5 \ l f \ l f 5 1 \ l f \ l f 1 \ l f \ l f 1 6 \ l f \ l f 6 \ l f \ l f 6 2 \ l f \ l f ...

  • Page 33: Appendix 3

    Nextel roadrunners scanner programming guide last updated: 10/14/05 29 © baracoda 2005 appendix 3 for more information, see symbology settings => symbology identifier. The symbology identifier prefix is a two or three character string: ] c m where ]: si indicator c: symbology identification m:modifi...