1. DL manuals
  2. Barco
  3. Medical Equipment
  4. CORONIS 1MP
  5. Installation & User Manual

Barco CORONIS 1MP Installation & User Manual

Other manuals for CORONIS 1MP: System Manual, System Manual

Summary of CORONIS 1MP

  • Page 1

    Installation & user manual coronis 1mp.

  • Page 2

    3 copyright notice................................................................................... 7 preface ................................................................................................. 8 safety instructions........................................................................

  • Page 3

    4 introduction ................................................................................ 77 using the barcomed driver tab ................................................. 77 status .......................................................................................... 79 palette mode .......

  • Page 4

    5 selecting inputs........................................................................ 127 settings ..................................................................................... 128 preset* ...................................................................................... 130 getting...

  • Page 5

    6 troubleshooting...................................................................... 153 setting the resolution of your c oronis 1mp display ............... 155 windows nt 4.0 display resolution......................................... 155 windows 2000 display resolution ............................

  • Page 6

    Copyright notice 7 copyright notice this document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems...

  • Page 7

    Preface 8 preface notice although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable documentation possible; if you discover errors, please let us know. Bar...

  • Page 8

    Preface 9 disposal information the lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local ordinances or regulations..

  • Page 9

    Safety instructions 10 safety instructions general recommendations read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instru...

  • Page 10

    Safety instructions 11 • power cords: power cord with cee 7 plug: the colors of the mains lead are colored in accordance with the following code: green-and- yellow: earth (safety earth), blue: neutral, brown: line power cord with ansi 73.11 plug: the wires of the power cord are colored in accordance...

  • Page 11

    Safety instructions 12 this apparatus conforms to: ce, iec 60950, ul 60950, can/csa c22.2 no. 60950 (c-ul), ccc. National scandinavian deviations for cl. 1.7.2 : finland: "laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan" norway: "apparatet må tilkoples jordet stikkontakt" s...

  • Page 12

    13 display controller installation.

  • Page 13

    Display controller installation 14 (this page intentionally left blank.).

  • Page 14

    Barcomed c oronis display controller overview 15 barcomed c oronis display controller overview the barcomed c oronis display controller delivers a quality image with 1024 simultaneous shades of gray for medical viewing applications. Minimum system requirements • pentium ii 266 mhz with 128 mb ram (p...

  • Page 15

    Barcomed c oronis display controller overview 16 supported resolutions for each head of the barcomed c oronis display controller for coronis 1mp displays • 1024 x 1280 @ 60 hz (primary) • 1280 x 1024 @ 60hz for all barcomed c oronis display controllers the following resolution is also available when...

  • Page 16

    Barcomed c oronis display controller installation 17 barcomed c oronis display controller installation caution: wear a grounded, protective esd strap during installation or handling of the display controller. Electrostatic charges can damage the display controller. Prior to installing your barcomed ...

  • Page 17

    Barcomed c oronis display controller installation 18 figure 2: vga jumper enlarged view using the vga capabilities of the barcomed c oronis prior to installing the barcomed c oronis , decide if you are going to use its on-board vga capabilities. If you are, check the setting of the jumper at j-1 on ...

  • Page 18

    Barcomed c oronis display controller installation 19 figure 3: pci and raid controller slots install the barcomed c oronis controller in your computer following these steps: 1. Turn off the power to your computer and disconnect the power cord, however make sure that the computer chassis is still gro...

  • Page 19

    Barcomed c oronis display controller installation 20 below) using the provided dvi cable. For a dual-headed barcomed c oronis setup, connect the secondary display to the other connector on the display controller. 7. Replace the chassis cover, reconnect the power cord, turn on the power, and boot the...

  • Page 20

    21 display installation.

  • Page 21

    Display installation 22 (this page intentionally left blank.).

  • Page 22

    Overview 23 overview introduction the mfgd 1318, barco’s 18” 1 megapixel grayscale lcd display, guarantees perfect image quality in medical imaging applications. The display combines a tft (thin film transistor) liquid crystal display panel structure and a built-in backlight with inverter for a bett...

  • Page 23

    Overview 24 autoscan when you connect a video signal, the display checks in the internal memory if the signal has been adjusted before. If so, it selects the settings and parameters that match the connected signal. When you connect a video signal that hasn’t been connected before, and adjust the dis...

  • Page 24

    Overview 25 package contents the package should include the following items, please check. If some of the items are missing, please contact the reseller from whom you have purchased the unit. • the mfgd 1318 display • power supply • dvi cable • analog video cable • usb cable • two velcro strips to b...

  • Page 25

    Overview 26 controls and connectors figure 5 front (1) ambient light compensation (alc) sensor (2) power led • the led is off when the display is off. • the led is green when the display is on (when enabled in the on-screen menus). • the led is orange when the display is in stand-by power- saving mo...

  • Page 26

    Overview 27 figure 6 side (3) usb downstream connector (4) control wheel for navigating through the on-screen display (osd) menus and changing values in the menus figure 7 rear (5) digital dvi (video and data) input (6) d15 (vga) video connector (7) vertical sync input (8) composite / horizontal syn...

  • Page 27

    Overview 28 (9) composite video input (10) usb downstream connector (11) usb upstream connector (12) dc 12v power input.

  • Page 28

    Installation 29 installation precautions • keep your original packaging. It is designed for this display and is the ideal protection during transport. • avoid reflections in the flat panel to reduce eye strain. • place the display on a strong and stable table or desk. • keep the display away from he...

  • Page 29

    Installation 30 to remove the clip: 1. Position the display with its rear side facing you. 2. Lift up the 2 clips of the foot cover to release the cover from the foot. 3. Pull the lower side of the cover towards you and simultaneously slide the cover downward. 4. Pull the red clip out of the fixatio...

  • Page 30

    Installation 31 figure 9 should you change the panel orientation without tilting it first, you might irreversibly damage the tilt & swivel mechanism. 3. To change from portrait to landscape, turn the panel counterclockwise while tilting it slightly. 4. To change from landscape to portrait, turn cloc...

  • Page 31

    Installation 32 2. Connect the other end of the dvi cable to the video output of your dvi signal source. 3. Route the cable so that it enters the connector compartment at the place where the cover is bulged. To connect analog video & sync cables on bnc: connect the video & sync output of the signal ...

  • Page 32

    Installation 33 notes: • the video inputs cannot be connected in loop-through (daisy-chain). • the required video amplitude: 700 mv ± 3 db. • the required sync. Amplitude: • vs input: 700 mv to 4 v • hs/cs input: 500 mv to 4v • video input (sync on video): 150 mv to 600 mv to connect analog video & ...

  • Page 33

    Installation 34 3. Connect the other end of the power cord to a grounded power outlet. 4. Route the cable so that it enters the connector compartment at the place where the cover is bulged. Routing the signal cables after connecting all cables, fix them in the cable tie at the rear of the connector ...

  • Page 34

    Installation 35 3. Press the cover to the foot so that both clips make a clicking sound. Using the usb hub the usb interface inside the display allows you to connect usb devices, such as a keyboard, mouse or digital camera, to the display. To use the usb hub: 1. Connect the display’s usb upstream co...

  • Page 35

    Installation 36 2. If necessary, select a suitable resolution or signal format for the signal source..

  • Page 36

    37 software installation.

  • Page 37

    Software installation 38 (this page intentionally left blank.).

  • Page 38

    Software installation overview 39 software installation overview the barcomed software installation section has been divided into two sections. One for windows nt 4.0 and the other for windows 2000 and windows xp. Software in addition to the device drivers for your barcomed display controller(s), yo...

  • Page 39

    Software installation overview 40 with the c oronis 3mp flat panel displays and is available as an option for the c oronis 1mp and 2mp flat panel displays. Barcomed software installation wizard the barcomed software installation wizard is a graphical user interface (gui) designed to install the barc...

  • Page 40

    Windows nt 4.0 barcomed c oronis software installation 41 windows nt 4.0 barcomed c oronis software installation special note: prior to installing the barcomed drivers and related software you must install the barcomed display controller(s), connect the coronis display panel(s) to the controller(s),...

  • Page 41

    Windows nt 4.0 barcomed c oronis software installation 42 figure 13 if it determines that the microsoft installer is either out of date or missing, it will display the screen shown in figure 14. Click “ok” to continue, the wizard will then install a newer version of the microsoft installer. Figure 1...

  • Page 42

    Windows nt 4.0 barcomed c oronis software installation 43 2. By default all the software on the barcomed software cd will be selected (figure 15 below). For the initial installation we recommend that you install all of the software. If you do not want to install a particular barcomed software produc...

  • Page 43

    Windows nt 4.0 barcomed c oronis software installation 44 figure 16 if you selected a device with an existing driver, the wizard will warn you if the current driver is newer than the one you are installing (figure 17 below). Figure 17 click “ok” to continue. If you want to change your selection, cli...

  • Page 44

    Windows nt 4.0 barcomed c oronis software installation 45 6. When the screen shown in figure 18 below appears select the palette mode which is the correct one for your viewing application. If you are uncertain use the default settings. You can change the palette mode later (see “palette mode” on pag...

  • Page 45

    Windows nt 4.0 barcomed c oronis software installation 46 welcome screen of the barcomed product install wizard to select additional software to install. When you click “finish” windows may prompt you to restart your system, if it does click “yes”. Note: clicking “cancel” will also return you to the...

  • Page 46

    Windows nt 4.0 barcomed c oronis software installation 47 figure 19 9. The “customer information” screen will appear. The installer will automatically fill in the blanks using the information entered when windows was installed on your system. You may change this information if you wish. Click “next”...

  • Page 47

    Windows nt 4.0 barcomed c oronis software installation 48 return to the barcomed product install wizard welcome screen. After returning to the barcomed product install wizard welcome screen, the wizard will clear the checkbox next to dpms screen saver and will automatically launch the barco i-switch...

  • Page 48

    Windows nt 4.0 barcomed c oronis software installation 49 16. When the barco i-switch software installshield wizard has finished installing the software, it will tell you that it has finished installing the software on your computer and prompt you to click “finish” to complete the setup. Click “fini...

  • Page 49

    Windows nt 4.0 barcomed c oronis software installation 50 figure 20: the windows nt 4.0 display properties control panel after the drivers have been installed and the resolution set. Note: the system shown in figure 20 is a single barcomed c oronis display controller, no 3 rd party vga card configur...

  • Page 50

    Windows nt 4.0 barcomed c oronis software installation 51 select “ok”. 4. Select the “test” button and click on “ok” to test the display. You will be asked if it displayed correctly. If the test pattern displays correctly, select “yes”. If not, click on the “list all modes” button and try selecting ...

  • Page 51

    Windows nt 4.0 barcomed c oronis software installation 52 must restart it and boot normally for your changes to take effect. 7. When your system restarts select the “nt version 4.0” option ( not the vga mode option ). Log in as usual. If you wish to change the number of c oronis display panels you a...

  • Page 52

    Single source master windows 2000 barcomed c oronis software installation 53 windows 2000 barcomed c oronis software installation note: these instructions apply to both windows ® 2000 and windows ® xp. Preparation prior to installing your c oronis 1mp software the following should be done. 1. Instal...

  • Page 53

    Windows 2000 barcomed c oronis software installation single source master 54 changed later using the barcomed driver tab of the windows display properties control panel. Note: both displays connected to a single display controller must have the same physical orientation and resolution in order to be...

  • Page 54

    Single source master windows 2000 barcomed c oronis software installation 55 the barcomed product installation wizard will display the barcomed product installation wizard’s welcome screen (see 21 on page 55). If the screen shown in figure 21 appears, please skip to step “5.” on page 56, otherwise c...

  • Page 55

    Windows 2000 barcomed c oronis software installation single source master 56 figure 22 the barcomed product installation wizard will advise you when it has successfully installed the new version of the microsoft installer. Click “ok”. The wizard may prompt you to restart your system. If it does, cli...

  • Page 56

    Single source master windows 2000 barcomed c oronis software installation 57 figure 23 driver installation 6. Click “next” on the display driver wizard’s welcome screen to continue or “cancel” to exit the display driver wizard and return to the software install wizard. The device selection screen’s ...

  • Page 57

    Windows 2000 barcomed c oronis software installation single source master 58 your coronis 1mp software cd. Select the device you want to install and then click “next”. Note: if there are no barcomed devices installed, or if windows does not recognize the installed devices, or if the driver on your c...

  • Page 58

    Single source master windows 2000 barcomed c oronis software installation 59 figure 25 click “ok” to install the new driver. If you don’t want to replace the exiting driver, click “ok” and then click “cancel”. 7. Your selection on the "enable dualview" screen (figure 26 below) determines if dualview...

  • Page 59

    Windows 2000 barcomed c oronis software installation single source master 60 figure 27: dualview disabled—rectangle 2 represents the combined heads of the barcomed controller. Figure 28: dualview enabled—rectangles 2 & 3 represent the individual heads of the barcomed controller. Special note: if you...

  • Page 60

    Single source master windows 2000 barcomed c oronis software installation 61 adapters" in the "device manager control panel". The second device will be disabled. This is normal. Do not try to enable any of the disabled display adapters. 8. The “device confirmation” screen displays the device driver ...

  • Page 61

    Windows 2000 barcomed c oronis software installation single source master 62 figure 30: windows xp windows logo testing warning 10. When the screen shown in 31 on page 63 appears select the palette mode which is the correct one for your viewing application. If you are uncertain use the default setti...

  • Page 62

    Single source master windows 2000 barcomed c oronis software installation 63 figure 31 when the driver install wizard tells you that it has successfully installed the selected driver, click “finish”. The wizard will now begin installing the next selected piece of barcomed software. If you are workin...

  • Page 63

    Windows 2000 barcomed c oronis software installation single source master 64 driver. The wizard will also begin to install the next selected piece of barcomed software. If the wizard failed to successfully install the selected driver, it will warn you that the installation failed. Click “finish” to ...

  • Page 64

    Single source master windows 2000 barcomed c oronis software installation 65 may change this information if you wish. Click “next” to continue. 12. The “setup type” page will now appear. Choose “typical” to install the default schemes with english names. Choose “custom” to install the default scheme...

  • Page 65

    Windows 2000 barcomed c oronis software installation single source master 66 3. Click “next” on the choose destination location screen to install the niowatch software in the default location. Or click “browse” to install the software in a different location. Figure 33 4. Click “next” on the select ...

  • Page 66

    Single source master windows 2000 barcomed c oronis software installation 67 install. When you click “finish” windows may prompt you to restart your system, if it does click “yes”. When your system restarts, boot normally and log in using an account with administrator privileges and turn to the sect...

  • Page 67

    Windows 2000 barcomed c oronis software installation single source master 68 12. Click “finish” to exit the barcomed product installation wizard or click “back” if you wish to install additional barcomed software. Windows may now warn you that you must restart your computer before the new settings w...

  • Page 68

    Single source master windows 2000 barcomed c oronis software installation 69 figure 35: windows xp windows logo testing warning the barco monitor plug and play software should automatically set the resolution for the displays of your coronis 1mp system. However, the second head of a dual headed syst...

  • Page 69

    Windows 2000 barcomed c oronis software installation single source master 70 (this page intentionally left blank.).

  • Page 70

    71 display controller tools.

  • Page 71

    Display controller tools 72 (this page intentionally left blank.).

  • Page 72

    Single source master barco display tab 73 barco display tab introduction the barco display tab is used for gathering information about the barcomed flat panel display(s). To access the barco display tab do the following: 1. Open the “display properties control panel” by right clicking on the desktop...

  • Page 73

    Barco display tab single source master 74 figure 37: barco display tab under windows 2000 and windows xp using the barco display tab displays all of the available display controllers that are of the same type as the current barco display controller are shown here graphically, with one display icon r...

  • Page 74

    Single source master barco display tab 75 properties you may access the properties page of the currently selected display, which is represented by the monitor icon above with the black frame around it, by either clicking on the “properties” button or double clicking on the icon. Barcomfd library thi...

  • Page 75

    Barco display tab single source master 76 figure 38.

  • Page 76

    Single source master barcomed driver tab 77 barcomed driver tab introduction after the barcomed windows display controller driver is installed, a new display properties tab is available for configuring special features of the barcomed display controller. Languages supported the barcomed driver tab s...

  • Page 77

    Barcomed driver tab single source master 78 figure 39: barcomed driver tab under windows nt 4.0 3. Under windows 2000 or windows xp, click on “settings” tab. Double click on the rectangle that represents the barco display whose settings you wish to change to bring up its property page. Click on the ...

  • Page 78

    Single source master barcomed driver tab 79 figure 40: barcomed driver tab under windows 2000 and windows xp status the status section displays information about the current barcomed display controller, driver, and the currently selected display resolution. Graphics board this displays the current b...

  • Page 79

    Barcomed driver tab single source master 80 resolution this displays the currently selected display resolution. Palette mode in the palette mode section you can choose one of the four following palette modes.If you are using a color display in conjunction with your barco grayscale display(s) under w...

  • Page 80

    Single source master barcomed driver tab 81 windows operating system, but applications can manipulate the middle 236 entries. This is the standard palette mode as configured by windows. Figure 41 static gray palette including standard system colors this option sets the palette to be a static set of ...

  • Page 81

    Barcomed driver tab single source master 82 static gray palette with no system colors this option sets the palette to be a static linear ramp of 256 shades of gray. Therefore, applications are denied the ability to dynamically change or allocate palette entries. This prevents palette conflicts betwe...

  • Page 82

    Single source master barcomed driver tab 83 enable directdraw this option allows the user to enable or disable directdraw. Directdraw is a software interface that provides direct access to display devices while maintaining compatibility with the windows graphics device interface (gdi). Directdraw pr...

  • Page 83

    Barcomed driver tab single source master 84 disable 10-bit grayscale use this option for standard windows®-based applications that require 8-bit color support (256 colors), such as internet explorer, excel, etc. Do not use this option for applications that require 10-bit pixel support (1024 simultan...

  • Page 84

    Single source master barcomed driver tab 85 one row” option from the pull-down list. This would cause the windows virtual desktop to be resized to fit on the three monitors, and you can move your cursor horizontally from one screen to the other. If “custom configuration” is displayed, it means that ...

  • Page 85

    Barcomed driver tab single source master 86 configuring the dualview or windows nt desktop display resolution under windows nt 4.0 all displays connected to all of the barcomed controller(s) installed in the system must have the same resolution settings. Under windows 2000 and windows xp both displa...

  • Page 86

    Barcomed hardware tab 87 barcomed hardware tab introduction the barcomed hardware tab is used for gathering information about barcomed display controller(s). For all barcomed display controller(s) it will display pci information. For barcomed display controller(s) based on the aura video chipset it ...

  • Page 87

    Barcomed hardware tab 88 using the barcomed hardware tab to access the barcomed hardware tab do the following: 1. Open the “display properties control panel” by right clicking on the desktop, then select “properties”. 2. Under windows nt 4.0, click on the “barcomed hardware tab” (see figure 44 on pa...

  • Page 88

    Barcomed hardware tab 89 figure 44 barcomed hardware tab under windows nt 4.0

  • Page 89

    Barcomed hardware tab 90 figure 45 barcomed hardware tab under windows 2000 or windows xp device displays the current barcomed display controller, driver, and the currently selected display resolution. Identify device: this button is for barcoview medical imaging systems (mis) internal use only and ...

  • Page 90

    Barcomed hardware tab 91 pci information device id: displays the device’s pci device id number. Vendor id: displays the device manufacturer’s pci vendor id number. Subsystem id: displays the device’s pci subsystem id number. Subsystemvendorid: displays the device’s pci subsystem vendor id number. Vg...

  • Page 91

    Barcomed hardware tab 92 problem. It probes the system for various types of system information, and saves it to a web-page report that can then be analyzed by the barco imagecare team. Barcomed self exam is implemented in a wizard format. The barcomed self exam wizard will first ask the user to prov...

  • Page 92

    Barcomed hardware tab 93 customer information screen all fields on this screen must be filled in. This screen asks the user for contact information that will help the barco support team contact the customer. The user will not be allowed to move forward to the next screen unless all of the fields are...

  • Page 93

    Barcomed hardware tab 94 the information is gathered, the user may not go back in the wizard screens. Completion screen the barcomed self exam has collected all of the information. A report called barcoselfexam.Html with all of the diagnostic data that was collected is created. If a summary report w...

  • Page 94

    Barcomed hardware tab 95 6. Attach the barcomed self exam report(s) to the email message and send it. You will receive an acknowledgment of receipt of your email by the end of the next business day..

  • Page 95

    Barcomed hardware tab 96 update device... Button: clicking this button will launch the barcomed hardware configuration utility. This program allows the user to flash update the firmware stored in the rom of the currently selected barcomed display controller. The barcomed hardware configuration utili...

  • Page 96

    97 display tools.

  • Page 97

    Display tools 98 (this page intentionally left blank.).

  • Page 98

    Single source master barco dpms screen saver 99 barco dpms screen saver introduction the barco dpms (display power management signaling) screen saver allows the user to set power and display saving features for medical displays controlled by barcomed display controllers. At the end of the work day, ...

  • Page 99

    Barco dpms screen saver single source master 100 barco dpms screen saver options from the “barco dpms screen saver control panel” you can change many dpms screen saver elements simultaneously. The dpms screen saver elements in each scheme are work schedule, work day screen saver, dpms settings after...

  • Page 100

    Single source master barco dpms screen saver 101 day, the display is set to one of the dpms states (stand-by, suspend, or off) by the display controller during user inactivity. Screen saver during work day on lcd based displays, such as the barco c oronis displays, it is not necessary to invoke a sc...

  • Page 101

    Barco dpms screen saver single source master 102 if requested, the display will first go into stand-by state, then into suspend state, and then into off state. The properties of dpms states are listed in the following table: monitor settings if you have a barco medical display, select “barco quick s...

  • Page 102

    Single source master barco dpms screen saver 103 schemes are separated into two kinds, default (global) and private (personal). Upon installation, three default settings schemes are installed and no private settings schemes are installed. Default settings schemes are visible to all users of the syst...

  • Page 103

    Barco dpms screen saver single source master 104 dpms screen saver as his screen saver, the next time he logs on to the system the screen saver selection may be blank. After selecting the barco dpms screen saver the user must then select a settings scheme for the screen saver to follow. To set up th...

  • Page 104

    Single source master barco dpms screen saver 105 figure 47: windows 2000 screen saver tab figure 48: windows xp screen saver tab 2. Click on the “settings” button. The “barco dpms screen saver control panel” will open (see figure 49 on page 106)..

  • Page 105

    Barco dpms screen saver single source master 106 figure 49: barco dpms settings control panel 3. Use the default schemes by selecting one of the three default schemes. Click “ok”. Then click “ok” again. Note: if you make any changes to any of the settings of one of the three default schemes, the cur...

  • Page 106

    Single source master barco dpms screen saver 107 figure 50 to create a new scheme by modifying one of the three default schemes please do the following. 1. Open the “display properties control panel” by right clicking on an empty space of the desktop and selecting “properties” from the drop down men...

  • Page 107

    Barco dpms screen saver single source master 108 amount of time it takes your display to warm up via the “monitor setting” section. Contact your display vendor for this warm-up time. On barco c oronis displays, the i-guard will stabilize the image within a few seconds after the display returns to th...

  • Page 108

    Single source master barco dpms screen saver 109 2. Click “next” on the welcome screen of the barco dpms installshield ® wizard to begin the installation. 3. Select the radio button next to “remove” on the program maintenance screen of the wizard and click “next”. 4. Click “remove” on the remove pro...

  • Page 109

    Barco dpms screen saver single source master 110 (this page intentionally left blank.).

  • Page 110

    Barco i-switch software 111 barco i-switch software overview note: the barco i-switch software is only available for systems which have the portrait accelerator in the c oronis display panel and barcomed display driver releases that include the barco i- switch software. The barco i-switch software m...

  • Page 111

    Barco i-switch software 112 must be rotated to the same orientation before the barco i-switch software will change the resolution for the displays connected the system. Windows 2000 and windows xp although windows 2000 and windows xp support multiple types of display controllers, rotating a single h...

  • Page 112

    Barco i-switch software 113 5. Type the following text in the command line window: “coronisrotationservice /uninstall”. 6. When the program has finished, closed the command line window..

  • Page 113

    Barco i-switch software 114 (this page intentionally left blank.).

  • Page 114

    115 display operation.

  • Page 115

    Display operation 116 (this page intentionally left blank.).

  • Page 116

    Operation 117 operation operating precautions continuous operation of the display with the same screen may result in some image sticking on the lcd panel. Over 10 hours operation with the same image content is not recommended. Switching on the display dpms may decrease the risk of image sticking (im...

  • Page 117

    Operation 118 • the functions that are not present in dvi mode are indicated with an * throughout this manual. Navigating through the menus • the menu system has a hierarchical structure, with several levels. To display the on-screen menus, turn the wheel (4). The main menu appears. This is the top ...

  • Page 118

    Operation 119 • click the wheel shortly. The adjustment name appears, as well as the current adjustment value • turn the wheel to change the value • click the wheel shortly to confirm the change and return to the menu • some adjustments can be made by selecting from a range of predefined settings. T...

  • Page 119

    Operation 120 using the autoset* functions * not in dvi mode the autoset menu provides a set of functions to adjust the display automatically. When do you need to use the autoset functions? It is necessary to perform the auto gain and auto phase calibrations in the following cases: • the first time ...

  • Page 120

    Operation 121 to enter the autoset menu: 1. In the main menu, turn the control wheel to select the autoset menu. * not in dvi mode 2. Click the control wheel. The autoset menu appears. 3. Turn the control wheel to select the function you wish to execute. 4. Execute the function as described below. M...

  • Page 121

    Operation 122 the autoset menu contains the following items: controlling video contrast* and video brightness* * not in dvi mode to enter the menu: 1. In the main menu, turn the control wheel to select the video contrast or video brightness menu. 2. Click the control wheel to enter the video contras...

  • Page 122

    Operation 123 to change video contrast or video brightness manually: 1. Turn the control wheel to select the manual contrast (brightness) control. 2. Click the control wheel to enter the control. 3. Turn the control wheel to change the video contrast or video brightness value. 4. Click the control w...

  • Page 123

    Operation 124 setting the luminance value with this function, the backlight value is stabilized by the i-guard sensor. The value you enter is the target backlight luminance, expressed in cd/m². Proceed as follows: 1. In the main menu, turn the control wheel to select the luminance menu. 2. Click the...

  • Page 124

    Operation 125 making adjustments how to make the adjustments? 1. In the main menu, turn the control wheel to select the adjustments menu. 2. Click the control wheel. The adjustments menu appears. * not in dvi mode 3. Turn the control wheel to select the adjustment menu you wish to enter: geometry or...

  • Page 125

    Operation 126 geometry adjustments the geometry menu contains the following items: * not in dvi mode ** available only if the portrait accelerator option is installed phase adjustments* * not in dvi mode automatic geometry* this is the same function as in the autoset menu. Please refer to the descri...

  • Page 126

    Operation 127 required test pattern to obtain good results, it is necessary to have a good image on which to perform the functions. For the phase adjustments, the pattern should contain sharp black-white transitions, like a line pattern or characters. The phase menu contains the following items: we ...

  • Page 127

    Operation 128 2. Click the control wheel. The input selection control appears. 3. Turn the wheel to select the desired input setting. 4. Click the wheel to activate the input selection and return to the main menu. You can select the following input selection settings: settings to enter the settings ...

  • Page 128

    Operation 129 2. Click the control wheel. The settings menu appears. 3. Turn the wheel to select the desired menu item. 4. Perform the settings as described below. The settings menu contains the following items : dpms click the control wheel to switch on/off the automatic power saving system (dpms) ...

  • Page 129

    Operation 130 preset* *not in dvi mode to enter the preset menu: 1. In the main menu, turn the control wheel to select the preset menu. * not in dvi mode 2. Click the control wheel. The preset menu appears. 3. Turn the wheel to select the desired menu item. 4. Perform the settings as described below...

  • Page 130

    Operation 131 the preset menu contains the following items: getting information the information menu allows you to get information about the display and the connected signals. To enter the information menu: 1. In the main menu, turn the control wheel to select the information menu. * not in dvi mode...

  • Page 131

    Operation 132 4. Click the wheel to select the menu item. The general information menu contains the following items: the current input format information menu contains the following items: product the display type serial no indicates the display serial number sw version displays the current internal...

  • Page 132

    Advanced functions 133 advanced functions about this chapter important the functions described in this chapter are intended for trained service staff only! Improper use of these functions may disorder the display. Barco cannot be held responsible for the results or damage caused by improper use of t...

  • Page 133

    Advanced functions 134 advanced functions in the adjustments menu geometry in advanced mode, the geometry menu additionally contains the following functions: ambient light compensation ambient light compensation is sometimes abbreviated to alc. See introduction. The ambient light compensation menu c...

  • Page 134

    Advanced functions 135 low pass filter* * not in dvi mode the display electronics provide 4 different low-pass filters to filter possible high-frequent distortion from an analog video signal. Select a different filter in case the image contains high-frequent noise or distortion. Select the filter th...

  • Page 135

    Advanced functions 136 • if you select none, no display function will be selected. • the selection test lut is meant for internal test purposes. It should not be selected for normal operation. Input mode* *not in dvi mode to change the input mode setting, click the control wheel. Turn the wheel to s...

  • Page 136

    Advanced functions 137 standard input mode note: the lcd panel used in this display is originally an rgb panel, of which the colors are disabled. All rgb subpixels are used for grayscale reproduction. Extended input mode the submenu extended contains all the items from the standard submenu, plus the...

  • Page 137

    Advanced functions 138 osd position with the osd function you can select where on the screen the osd menu text will appear. You can select between center position, top left, top right, bottom left or bottom right. Advanced functions in the preset menu the preset menu contains the following advanced ...

  • Page 138

    Advanced functions 139 advanced functions in the information menu the following advanced functions are situated in the general information menu. Service the service information menu contains the following items: firmware the firmware information menu contains the following items: runtimes the runtim...

  • Page 139

    Advanced functions 140 backlight runtime indicates the time the backlight has been on since the last time it was switched off (e.G., in stand-by). This counter stops after 1092 min- utes..

  • Page 140

    Maintenance 141 maintenance panel take care not to damage or scratch the panel. Clean with a soft woolen or cotton towel. Use a watery solution or a mild commercial glass-cleaning product suited for coated glass surfaces. Cabinet do not use chemical cleaning products, benzene, toluene, xylene or oth...

  • Page 141

    Maintenance 142 2. Tilt the panel. 3. Unscrew the 4 sunken screws at the rear, fixing the glass panel and bezel. 4. Unplug the cable plugged in on the bezel. 5. Remove the bezel with glass panel. Cleaning instructions: • dust, fingerprints, grease etc. Can be removed by using a soft damp cloth (a sm...

  • Page 142

    Troubleshooting 143 troubleshooting windows does not show the desired display settings should you have problems selecting display settings for portrait oriented displays in the windows display properties control panel, disable the option hide modes that this monitor cannot display in the control pan...

  • Page 143

    Troubleshooting 144 pixel faults permanently dark or bright pixels can happen to tft displays. 10 or less permanently dead pixels do not make out a good case for exchanging the unit. Please contact our customer service department if the number of pixel faults exceeds the above-mentioned figure..

  • Page 144

    Technical specifications 145 technical specifications geometry • screen size: 46 cm (18.1") • display area: 359 mm x 287 mm (14.1" x 11.3") • aspect ratio: 5:4 visual performance general • pixel arrangement: sub-pixel vertical stripes • pixel pitch: 0.2805 mm x 0.2805 mm (0.011" x 0.011") • panel co...

  • Page 145

    Technical specifications 146 inputs dvi • complies to dvi rev. 1.0 spec up to uxga 60 hz video • connector type: bnc / d15 • inputs provided: composite video • video input voltage: nominal 0.7vpp • termination: 75 ohm sync • connector type: bnc / d15 • inputs provided: hs/cs and vs sync input voltag...

  • Page 146

    Technical specifications 147 controls • on-screen display (osd) • rotary / push control wheel to navigate through the osd • usb • ddc power supply power source • input for external 12 vdc power supply unit: 90 ~ 264 vac • input for display: 12 vdc. (the supplied 12 vdc power supply must be used) pow...

  • Page 147

    Technical specifications 148 due to our policy of continuous product improvement, the above specifications are subjected to change without notice. Barco shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or conse- quential damages whatsoever resul...

  • Page 148

    149 medical software installation and operation.

  • Page 149

    Medical software installation and operation 150 (this page intentionally left blank.).

  • Page 150

    Medical pro installation and operation 151 medical pro installation and operation medical pro software installation install medical pro on the pc. Follow the instructions from the medical pro user guide. Important: do not forget you have to have administrator privileges to install or uninstall medic...

  • Page 151

    Medical pro installation and operation 152 8. Run the due tasks. Please refer to the medical pro user guide for more information..

  • Page 152

    153 troubleshooting.

  • Page 153

    Troubleshooting 154 (this page intentionally left blank.).

  • Page 154

    Single source master 155 setting the resolution of your c oronis 1mp display windows nt 4.0 display resolution in order to set the resolution of your c oronis 1mp display you must be logged in using an account with administrator privileges. 1. To set the resolution of your coronis 1mp display(s) rig...

  • Page 155

    Single source master 156 3. Select a resolution from the list that is correct for the maximum number of display adapters installed even if you will later configure for less than the maximum number of displays supported by your configuration. (see table 4 below for examples.) select “ok”. 4. Select t...

  • Page 156

    Single source master 157 windows 2000 display resolution tip: these instructions apply to both windows ® 2000 and windows ® xp. Important: if you are using a color display in conjunction with your barco grayscale display(s) you should configure your desktop before setting the resolution of the your ...

  • Page 157

    Single source master 158 setting the resolution of your c oronis 1mp display in order to set the resolution of your c oronis 1mp display you must be logged in using an account with administrator privileges. 1. To set the resolution of your coronis 1mp display(s) right click on the desktop and select...

  • Page 158

    Single source master 159 controller, you may need to temporarily make another display the primary display caution: if you have a single display configuration and you have enabled dualview, windows will not allow you to attach the second head. This is normal and not a bug. 4. For the display which is...

  • Page 159

    Single source master 160 the display you detached in step 2 above, by right clicking on the rectangle that represents it and selecting “attached”. Now repeat steps 5-8 above for this display. If you are using a quad-head configuration repeat all of the above steps for the two displays on the second ...

  • Page 160

    Single source master driver re-installation, updates or removal 161 driver re-installation, updates or removal reinstalling or updating your barcomed c oronis driver note: these instructions apply to windows nt 4.0, windows 2000 and windows xp. Important for windows 2000 or windows xp users only: if...

  • Page 161

    Driver re-installation, updates or removal single source master 162 figure 56 3. To update the driver, clear the checkbox next to “dpms screen saver” and “i-switch” (figure 57) and click “install”..

  • Page 162

    Single source master driver re-installation, updates or removal 163 figure 57 4. For windows nt 4.0 please turn to step 3 on page 21 in the section titled “windows nt 4.0 barcomed c oronis software installation”. For windows 2000 or windows xp please turn to step 6 on page 38 in the section titled “...

  • Page 163

    Driver re-installation, updates or removal single source master 164 uninstalling the barcomed c oronis driver 1. Insert your barcomed c oronis software cd into your computer’s cd drive. If the “barcomed product installation wizard” doesn’t start within one minute, browse the contents of your coronis...

  • Page 164

    Single source master driver re-installation, updates or removal 165 figure 58 4. Click “next”. 5. On the next screen (see figure 59 on page 165), check the checkbox next to “uninstall this device” and click “next” to continue. Figure 59 6. Click “next”..

  • Page 165

    Driver re-installation, updates or removal single source master 166 7. If you installed your driver with dualview enabled, skip to step 8. If you installed your driver with dualview disabledcloned heads active, click “next” to continue. Then click “finish” to complete the uninstall process. Click “f...

  • Page 166

    Single source master driver re-installation, updates or removal 167.

  • Page 167

    Www.Barco.Com b4100521-01 june 2005.