Barco DCS-100 Quick Start Manual
Quick Setup and Operations
5
6
8
Set Output Format — Set the desired output
resolution and frame rate. (Chapter 4, “Output
Format”)
9
Save Output Configuration — After completing all
output adjustments, save the output configuration.
(Chapter 4, “Save Output Config”)
11
Enable Test Pattern — Turn on a test pattern, verify
an image, and adjust as required. When complete,
turn off the pattern. (Chapter 4, “Test Pattern”)
Select and Adjust Input — Select an input, and
perform the necessary image adjustments. (Chapter
4, “Input Menu”)
12
Adjust System Parameters — Adjust parameters
such as transition time, display brightness, user prefs.
(Chapter 4, “Trans Time,” “System Menu”)
13
14
Repeat for Each Input — Repeat steps 9 and
10 for each input that you have connected to the
DCS-100.
10
Save System Configuration — After completing all
system adjustments, save the system configuration.
(Chapter 4, “Save System State”)
15
Ready to Roll — With all output, input and system
configurations saved, press the desired input button,
and press TAKE.
16
7
Launch GUI — (Optional) Connect your laptop to the
DCS-100, log onto the DCS-100 using its IP address,
and launch the GUI. (Chapter 5, “GUI Operations”)
Save Input Configuration — After completing all
adjustments for an input, save the input configuration.
(Chapter 4, “Save Input Config”)
Adjust Key Source — As required, select the
desired key source and adjust its clip, gain and
opacity. (Chapter 4, “Using Keys”)
Enable Remote Control — (Optional) Connect
Ethernet or Serial communications, and issue desired
commands. (Appendix B, “Remote Control”)
P/N 26-0604004-00, Rev 02
Adjust
Inputs
P R O G R A M :
N E X T :
DCS-100
R G B
1 0 2 4 x 7 6 8 @ 5 9 . 9 4
S D I
N T S C ( 4 8 0 i )
SEL
ESC
3
5
6
8
SDI
1
2
4
7
LOGO
Effects
KEY
TAKE
FRZ
BLACK
Inputs Section
Sources 1-6: Analog
Sources 7-8: DVI or Analog
SDI: SD-SDI or HD-SDI
LOGO: Full screen capture
Menu Display
Use ADJUST knob, plus
SEL and ESC buttons to
navigate menus.
Adjust
• Counter-clockwise: scroll down
menu tree, or decrement values.
• Clockwise: scroll up menu tree,
or increment values.
SEL
Press to enter a menu,
change or accept a
parameter, or answer
“Yes” to a query.
ESC
Press to exit a menu
without making changes,
cancel an operation, or
answer “No” to a query.
FRZ
Press to freeze or
un-freeze current
Program source.
Lit solid = frozen.
Button States
Off: Input not selected
Blinking (fast): Input being acquired
Blinking (slow): Input “pending” for transition
Lit solid: Input on Program
BLACK
Press to pend or initiate a black transition.
Black Auto Take mode affects function
(User Preferences). Blinking = Pending.
Lit solid = Black on Program.
KEY
Press to pend or initiate a key transition.
Key Auto Take mode affects function
(User Preferences). Blinking = Pending.
Lit solid = Key on Program.
TAKE
Press to mix the selected input
to Program, or to execute a
pending key or black transition.
Use the Setup Menu to adjust
the transition time.
NOTE
After each TAKE,
Program and pending
sources flip-flop.
Factory Reset – When using a DCS-100 for the
first time, perform a factory reset. (Chapter 4,
“Factory Reset”)
17
The following list summarizes DCS-100 setup and
operations. For error-free installation, always refer
to the listed section in the User’s Guide.
1
Connect Power — Ensure that power is properly
connected to the DCS-100. (Chapter 3, “Power
Installation”)
2
Connect Outputs — Connect the output(s) of the
DCS-100 to your projector(s) or other target devices.
(Chapter 3, “Signal Installation”)
Power On — Turn on power to the DCS-100, your
projector(s), and to all peripheral equipment.
(Chapter 4, “Power-Up Initialization”)
3
4
Connect Inputs — Connect all analog, DVI, and
SDI input sources to the DCS-100. (Chapter 3,
“Signal Installation”)
Quick Start Guide
Visibly yours
Toll Free:
Fax:
Technical Support:
Website:
+1 (888) 414-7226
+1 (916) 859-2515
+1 (866) 374-7878
www.barco.com
Barco Media and Entertainment
11101 Trade Center Drive
Rancho Cordova, CA
95670 • USA