1. DL manuals
  2. Barco
  3. Projector
  4. Graphics 808s R9000904
  5. Owner's Manual

Barco Graphics 808s R9000904 Owner's Manual

Summary of Graphics 808s R9000904

  • Page 1

    Barco projection systems date : 160501 art. No. : r5976283 r9000904 owner's manual graphics 808s revision : 00

  • Page 2

    Due to constant research, the information in this manual is subject to change without notice. Produced by barco nv, may 2001. All rights reserved. Trademarks are the rights of their respective owners. Printed in belgium barco n.V./projection systems noordlaan 5 b-8520 kuurne belgium tel : +32/56/368...

  • Page 3: Table of Contents

    Table of contents i-1 5976283 barcographics 808s 160501 table of contents table of contents ............................................................................................................................................................................... I-1 safety instructions ...........

  • Page 4

    Table of contents i-2 5976283 barcographics 808s 160501 right image focusing ......................................................................................................................................................................... 6-7 blue on source .....................................

  • Page 5: Safety Instructions

    Safety instructions 1-1 5976283 barcographics 808s 160501 warning to prevent fire or electrical shock hazard, do not expose this equipment to rain or moisture federal communication commission (fcc statement) this equipment has been tested and found to comply with the limits of a class a digital devi...

  • Page 6

    Safety instructions 1-2 5976283 barcographics 808s 160501 b. Power cord with ansi 73.11 plug: the wires of the power cord are colored in accordance with the following code. Green/yellow: ground white: neutral black: line (live) 3. Do not allow anything to rest on the power cord. Do not locate this p...

  • Page 7

    Location and functions of control 2-1 5976283 barcographics 808s 160501 2 location and function of controls rear panel terminology 1 ac power switch : to switch on the projector. Depending on the set-up of the projector during installation, the projector switches to standby or to 'operational mode. ...

  • Page 8

    Location and functions of control 2-2 5976283 barcographics 808s 160501 control panel terminology a. Gaining access to the keyboard the local keypath is underneath the top cover door with the barco logo. To open this door, push and turn it to the front side of the projector. This local keypad has th...

  • Page 9: Connections

    Connections 3-1 5976283 barcographics 808s 160501 3 connections ac power (mains) cord connection use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector on the lower part at the backside of the projector. Power check the power...

  • Page 10

    Connections 3-2 5976283 barcographics 808s 160501 start up with full white image. The next menu will be displayed for 30 seconds. A. Start up with warm up period. If no action is taken, a white image will be displayed for 20 minutes. This white image will be shifted on the faceplate of the crt to av...

  • Page 11

    Connections 3-3 5976283 barcographics 808s 160501 connecting a composite video source to port 1. Video input selection : press digit button 1 on the rcu or the local keypad. * note : if using the loop-through video output, then set the termination switch to the "off" position. Highlight port 2 : vid...

  • Page 12

    Connections 3-4 5976283 barcographics 808s 160501 connecting a rgb analog source to port 3. Connect your rgb source via an interface to port 3. Always use an interface when a computer and local monitor have to be connected to the projector. Available barco interfaces : universal analog interface r98...

  • Page 13

    Connections 3-5 5976283 barcographics 808s 160501 connecting a rgb analog source with tri-level sync to port 4/5. (option) rgb analog input terminals with tri level sync input or tri- level sync on green. The projector detects automatically where the sync signal is located. Rgb input selection : (rg...

  • Page 14

    Connections 3-6 5976283 barcographics 808s 160501 peripheral equipment connecting a rcvds 05 switcher to the retroprojector. - up to 20 inputs with the rcvds 05 switcher and up to 90 inputs when 10 rcvds switchers are linked via the 5-cable input modules. - serial communication with the projector. -...

  • Page 15: Controlling

    Controlling 4-1 5976283 barcographics 808s 160501 4 controlling caution : do not display a stationary image with full brightness and contrast for longer than 20 min., otherwise you risk damage to the crt's. Battery installation in the rcu. A new battery (not yet installed to save the battery life) i...

  • Page 16

    Controlling 4-2 5976283 barcographics 808s 160501 the barcoreality 812hs can be controlled with a. The rcu b. The hardwired rcu (cable not included) c. The local keyboard the procedure and results of controlling the projector with either of these rcu options is essentially the same. How to use your ...

  • Page 17

    Controlling 4-3 5976283 barcographics 808s 160501 how to program an address into the rcu? Press the address key (recessed key on the rcu) with a pencil and enter the address with the digit buttons. That address can be any digit between 0 and 9. When programming '0', zero address, the rcu will contro...

  • Page 18

    Controlling 4-4 5976283 barcographics 808s 160501 the bar scale increases when pressing on the + button (higher brightness) and decreases when pressing on the - button (lower brightness). Contrast control a correct 'contrast' setting is important for good image reproduction. Adjust the contrast to t...

  • Page 19

    Start up of the adjustment mode 5-1 5976283 barcographics 808s 160501 5 start up of the adjustment mode adjustment mode all picture geometry and convergence adjustments are made while in the 'adjustment mode'. Press the adjust key to enter the 'adjustment mode'. You are now in the 'adjustment mode'....

  • Page 20

    Start up of the adjustment mode 5-2 5976283 barcographics 808s 160501 some items in the adjustment mode are password protected. While selecting such an item, the projector asks you to enter your password. (password protection is only available when the password dip switch on the controller module is...

  • Page 21

    Random access adjustment mode 6-1 5976283 barcographics 808s 160501 6 random access adjustment mode starting-up the random access adjustment mode. Push the control disc é or ê to highlight "random access" and then press enter. Some items in the random access mode are password protected (when the pas...

  • Page 22

    Random access adjustment mode 6-2 5976283 barcographics 808s 160501 random access adjustment mode h size v size blanking left bottom right top v linearity coarse adjustment from next page from next page setup pattern selection focusing blue green red blue green red red and blue blue and green red an...

  • Page 23

    Random access adjustment mode 6-3 5976283 barcographics 808s 160501 selecting setup pattern if an external source is connected to the projector, this menu will be displayed. Push the control disc é or ê to highlight the desired setup pattern and then press enter. Genlocked pattern : internally gener...

  • Page 24

    Random access adjustment mode 6-4 5976283 barcographics 808s 160501 select with or then to return. Random access adjustment mode picture tuning geometry convergence focusing color select orbiting contr. Modulation soft edge select with or to accept to return. Picture tuning color balance sync : fast...

  • Page 25

    Random access adjustment mode 6-5 5976283 barcographics 808s 160501 sync fast/slow adjustment the sync function is used to minimize horizontal jittering or tearing at the top to the displayed image. Highlight sync by pushing the control disc é or ê and press enter to toggle between fast and slow. No...

  • Page 26

    Random access adjustment mode 6-6 5976283 barcographics 808s 160501 port 2 : video or s-video port 2 can be used as a video or s-video input. Highlight port 2 by pushing the control disc é or ê and press enter to toggle between video and s-video. Select with or to accept to return. Picture tuning co...

  • Page 27

    Random access adjustment mode 6-7 5976283 barcographics 808s 160501 focusing before starting the 'focusing' adjustment, be sure the lenses are correctly focused. Push the control disc forward or backward to select 'focusing' and press enter. Select with or then to return. Random access adjustment mo...

  • Page 28

    Random access adjustment mode 6-8 5976283 barcographics 808s 160501 geometry adjustments the geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color images : left-right (ew) and top-bottom corrections, blanking, horizontal amp...

  • Page 29

    Random access adjustment mode 6-9 5976283 barcographics 808s 160501 raster shift adjustment the green raster must be centered both horizontally and vertically on the center of the crt surface. To center the green raster, look into the green lens and use the control disc to move the raster. Caution i...

  • Page 30

    Random access adjustment mode 6-10 5976283 barcographics 808s 160501 left-right (east-west) adjustments left-right adjustments affect only the vertical lines of the projected image. Only the green image is displayed while making left-right adjustments. The red and blue images will automatically be c...

  • Page 31

    Random access adjustment mode 6-11 5976283 barcographics 808s 160501 seagull correction use this correction only if, after adjusting the vertical lines with the side bow or side keystone, still a 's' deformation is visible on the left and the right side of the image. The default value on the bar sca...

  • Page 32

    Random access adjustment mode 6-12 5976283 barcographics 808s 160501 top-bottom (north-south) adjustments top-bottom and center adjustments affect only the horizontal lines of the projected image. To start up the top-bottom and center corrections, follow the next procedure : push the control disc é ...

  • Page 33

    Random access adjustment mode 6-13 5976283 barcographics 808s 160501 seagull correction use this correction after the image has been adjusted with top and bottom bow and keystone. If still a deformation (like a seagull) on top and bottom of the image is visible, proceed to the seagull correction. Du...

  • Page 34

    Random access adjustment mode 6-14 5976283 barcographics 808s 160501 vertical linearity adjustment the vertical linearity adjustment function corrects for vertical non- linearities which extend from the center of the image to the top and bottom of the image. Push the control disc é or ê to highlight...

  • Page 35

    Random access adjustment mode 6-15 5976283 barcographics 808s 160501 select with or then to return. Blanking top bottom left right blanking adjustments blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black ou...

  • Page 36

    Random access adjustment mode 6-16 5976283 barcographics 808s 160501 convergence adjustment convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image wh...

  • Page 37

    Random access adjustment mode 6-17 5976283 barcographics 808s 160501 vertical corners highlight 'vertical corners' and press enter to start the adjustment. To make a coarse adjustment of the red or blue horizontal lines in zone 10, 14, 18 and 22 simultaneously. Select with or then to return. Coarse ...

  • Page 38

    Random access adjustment mode 6-18 5976283 barcographics 808s 160501.

  • Page 39: Service Mode

    Service mode 7-1 5976283 barcographics 808s 160501 select with é or ê then to return. Starting up the service mode. Use the control disc to highlight 'service' and then press enter. Some items in the service mode are password protected (when the password function is active). Enter your password to c...

  • Page 40

    Service mode 7-2 5976283 barcographics 808s 160501 identification highlight 'identification' with the control disc and press enter. The 'identification' screen gives information concerning : - projector address. To change the address of your projector, contact a qualified service technician. - softw...

  • Page 41

    Service mode 7-3 5976283 barcographics 808s 160501 deletion of blocks this item is password protected. The delete function is used to clear all data (settings) from an adjustment block. A delete can be given : - block by block or - for all blocks. Deleting block by block the delete a block function ...

  • Page 42

    Service mode 7-4 5976283 barcographics 808s 160501 change password this item is password protected. Highlight 'change password' with the control disc and press enter. The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control disc è or ç to select ...

  • Page 43

    Service mode 7-5 5976283 barcographics 808s 160501 set to midposition item is password protected. Highlight 'set to midposition' with the control disc and press enter to set all settings to their midposition. A confirmation menu will be displayed first. Select with or then to return. Service mode id...

  • Page 44

    Service mode 7-6 5976283 barcographics 808s 160501 dynamic astigmatism (spot shape adjustment) the spot shape adjustments correct the spot shape in 8 different areas on the screen for all three colors separately. The spot shape is adjusted according to the axial axises and the diagonal axises when u...

  • Page 45

    Service mode 7-7 5976283 barcographics 808s 160501 g2 adjust item is password protected. Highlight 'g2 adjust' with the control disc and press enter to continue. A safety notice will be displayed on the screen as it is necessary to open the top cover to adjust the g2. 'g2 adjustment should be perfor...

  • Page 46

    Service mode 7-8 5976283 barcographics 808s 160501 projector warm up highlight 'projector warm up' by pushing the control disc é or ê and press enter to select the projector warm up menu. Select with or then to return. Service mode g2 adjustment gamma corrections crt run in cycle projector warm up c...

  • Page 47

    Messages, warnings and failure codes 8-1 5976283 barcoraphics 808s 160501 8 messages, warnings and failure codes source 01 fh= 15.6 khz fv= 050 hz source 01 fh= 15.6 khz fv= 050 hz announcement of the selected source. E n t e r password xxxx message to enter your pass- word. Password contains 4 digi...

  • Page 48

    Messages, warnings and failure codes 8-2 5976283 barcographics 808s 160501 warning : go to stand by projector will switch to 'stand- by' when the rcvds is no longer available. Warning : invalid frequency input the entered frequency or ap- plied frequency of the source is out of the projector's range...

  • Page 49: Options

    Options 9-1 5976283 barcographics 808s 160501 hardwired rcu. The control signals from the rcu can be sent to the projector via a wired connection. 9 options shield conductor preparing your remote cable : use a shielded cable with a maximum length of 100 m and two mini- jack 3.5 mm connectors (order ...

  • Page 50

    Options 9-2 5976283 barcographics 808s 160501 magik interface multifuctional analog graphics interface kit. Barco's magik interface allows the user to connect a presentation device such as a projector or a professional monitor to any computer with analog video signal with or without maintaining the ...

  • Page 51: Numbers 90 - 99

    Adjustment blocks and source numbers 90-99 a-1 5976283 barcographics 808s 160501 adjustment blocks (memory blocks) as the projector is digitally controlled, all geometry and convergence adjustments are stored in the projector’s memory as numeric values. These numeric values are used to control digit...