- DL manuals
- Barco
- Projector
- MGP 15 Dicom Theater
- Hardware & Software Installation & User Manual
Barco MGP 15 Dicom Theater Hardware & Software Installation & User Manual
Summary of MGP 15 Dicom Theater
Page 1
Hardware & software installation & user manual mgp 15 dicom theater.
Page 2
2 mgp 15 dicom theater copyright this document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems - ...
Page 3
Mgp 15 dicom theater 3 interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Disposal information the lamps inside the display contain mer...
Page 4
4 mgp 15 dicom theater (this page intentionally left blank.).
Page 5
Table of contents 5 table of contents introduction ................................................................................ 9 about the system....................................................................... 11 about the separate components.................................................
Page 6
Table of contents 6 using the barcomed product installation wizard .............. 35 driver installation................................................................ 38 barco monitor plug and play software.............................. 42 display controller tools ....................................
Page 7
Table of contents 7 current scheme................................................................... 65 save as ................................................................................ 66 delete .................................................................................. 66 work sched...
Page 8
Table of contents 8 introduction ................................................................................ 85 source selection ......................................................................... 85 picture-in-picture selection........................................................ 86 p...
Page 9
9 introduction.
Page 10
Introduction 10 (this page intentionally left blank.).
Page 11
Introduction 11 about the system barco’s diagnostic display solutions are known for their image quality, fidelity and consistency. Building upon its wide expertise in medical imaging and high- end projectors, barco has expanded its lcd and crt display solutions with a dicom-compliant projection syst...
Page 12
Introduction 12 display other images, like presentations. Calibration and stabilization is done by using the external optical sensor, which is installed at the side of the large screen. The lcd display is used as review display in the dicom theater system. Calibration and stabilization of the displa...
Page 13
Introduction 13 minimum system requirements • windows 2000 (sp4) or windows xp (sp1) • pentium iv microprocessor • at least 1 free usb and com port per projector • a free pci slot per installed barcomed board.
Page 14
Introduction 14 dicom theater installation overview to install the dicom theater system completely, you have to follow these steps: 1. Install the barcomed display controller(s) in the pc. For more information, please refer to the section about the “display controller installation”. 2. Install and c...
Page 15
Introduction 15 installation examples this section illustrates the most common set-ups supported by dicom theater. A) single-head with 1 display and 1 projector figure 1 proceed as follows: 1. Connect one pc video output to the projector bnc input by means of the dvi-to-5 bnc cable (15 m / 50 ft). 2...
Page 16
Introduction 16 4. Connect the i-guard optical sensor to a free pc usb downstream connector. If the cable is not long enough, you have to use a usb booster/extender. Installation of the sensor is described more in detail in the section “medical and dicom theater software installation and usage”. B) ...
Page 17
Introduction 17 4. Connect a free pc com port to the second projector rs-232 connector by means of a d-sub9-to-d-sub9 cable (15 m / 50 ft). 5. Connect the first i-guard optical sensor to a free pc usb downstream connector. If the cable is not long enough, you have to use a usb booster/extender. 6. C...
Page 18
Introduction 18 3. Connect a free pc com port to the projector rs-232 connector by means of the d-sub9-to-d-sub9 cable (15 m / 50 ft). 4. Connect the i-guard optical sensor to a free pc usb downstream connector. If the cable is not long enough, you have to use a usb booster/extender. Installation of...
Page 19
Introduction 19 d) dual-head with two displays and two projectors figure 4 barco rs-232 usb video2 rs-232 barco video1 rs-232 video3 video4 rs-232 usb video1 usb video2 rs-232 video3 video4 video1 video2 video3 video4.
Page 20
Introduction 20 proceed as follows: 1. Connect one video output of the first display controller to the bnc input of the first projector by means of the dvi-to-5 bnc cable (15 m / 50 ft) (video 1 in the illustration above). 2. Connect the other pc video output of the first display controller to the d...
Page 21
Introduction 21 display controller, a display input and a projector input must be connected. E) dual-head with two displays and one projector (picture-in-picture) figure 5 proceed as follows: 1. Connect one pc video output of the first display controller to the dvi video input of the first display b...
Page 22
Introduction 22 2. Connect the other video output of the first display controller to the bnc input of the projector by means of the dvi-to-5 bnc cable (15 m / 50 ft) (video 2 in the illustration above). 3. Connect one pc video output of the second display controller to the dvi video input of the sec...
Page 23
23 display controller installation.
Page 24
Display controller installation 24 (this page intentionally left blank.).
Page 25
Barcomed 2mp2cp overview 25 barcomed 2mp2cp overview the barcomed 2mp2cp display controller delivers a quality image with 24-bit true color for medical viewing applications. Minimum system requirements • pentium 4, athlon or compatible processor • 256mb of system memory (minimum) for optimum perform...
Page 26
Barcomed 2mp2cp overview 26 • display properties control panel interface to dynamically change display settings • control panel supports the english (u.S.), dutch, german, korean, japanese, simplified chinese and traditional chinese languages • displays vga boot messages on dicom theater displays. S...
Page 27
Barcomed 2mp2cp overview 27 • 1920x1200, 24-bit true color.
Page 28
Display controller installation 28 display controller installation caution: wear a grounded, protective esd strap during installation or handling of the display controller. Electrostatic charges can damage the display controller. Prior to installing your barcomed 2mp2cp display controller(s) in your...
Page 29
Display controller installation 29 figure 7 below). By default, vga should be enabled, switch 1 on and switch 2 off. If you decide to use a separate vga monitor as your boot monitor, you must disable the barcomed 2mp2cp’s on- board vga capabilities by changing the switch settings to switch 1 off and...
Page 30
Display controller installation 30 figure 8: pci and raid controller slots installing the barcomed 2mp2cp display controller install the barcomed 2mp2cp controller in your computer following these steps: 1. Turn off the power to your computer and disconnect the power cord, however make sure that the...
Page 31
Display controller installation 31 6. Connect the primary display to the connector marked “vid 1” on the barcomed 2mp2cp display controller using the provided dvi cable (see figure figure 9 on page 31). For a dual-headed barcomed 2mp2cp setup, connect the secondary display to the other connector on ...
Page 32
Display controller installation 32 (this page intentionally left blank.).
Page 33
33 display controller software installation.
Page 34
Display controller software installation 34 (this page intentionally left blank.).
Page 35
Windows 2000 barcomed 2mp2cp software installation 35 windows 2000 barcomed 2mp2cp software installation note: these instructions apply to both windows ® 2000 and windows ® xp. Preparation prior to installing your dicom theater software the following should be done. 1. Install the barcomed 2mp2cp di...
Page 36
Windows 2000 barcomed 2mp2cp software installation 36 windows stops launching the “found new hardware wizard”. Please be patient as this may take several minutes while windows scans its library of plug-and-play device drivers to see if it has a driver for your barcomed 2mp2cp controller. 3. If windo...
Page 37
Windows 2000 barcomed 2mp2cp software installation 37 if it determines that the microsoft installer is either out of date or missing, it will display the screen shown in figure 11 below. Click “ok” to continue, the wizard will then install a newer version of the microsoft installer. Figure 11 the ba...
Page 38
Windows 2000 barcomed 2mp2cp software installation 38 figure 12 driver installation 6. Click “next” on the display driver wizard’s welcome screen to continue or “cancel” to exit the display driver wizard and return to the software install wizard. The device selection screen’s dialog box (figure 13 o...
Page 39
Windows 2000 barcomed 2mp2cp software installation 39 figure 13: sample device selection screen, the device shown in your system may be different. Caution: you can install the driver for only one type of barcomed device at a time. If you have multiple types of barcomed devices installed in your comp...
Page 40
Windows 2000 barcomed 2mp2cp software installation 40 click “back” to return to the device selection screen. Click “next” to begin installing the driver. Click “cancel” to abort the driver installation. Caution: once you click “next”, you cannot cancel the driver installation. Prior to beginning the...
Page 41
Windows 2000 barcomed 2mp2cp software installation 41 figure 16: windows xp windows logo testing warning 9. When the screen shown in figure 17 below appears decide if you want the driver to install with cloned heads mode enabled or disabled then click “next”. Figure 17 when the driver install wizard...
Page 42
Windows 2000 barcomed 2mp2cp software installation 42 the barcomed product install wizard or click “back” to return to the welcome screen of the barcomed product install wizard to select additional software to install. When you click “finish” windows may prompt you to restart your system, if it does...
Page 43
Windows 2000 barcomed 2mp2cp software installation 43 displays the screens shown in figure 18 below and figure 19 on page 43, click “yes” or “continue anyway” to continue. Figure 18: windows 2000 digital signature not found warning figure 19: windows xp windows logo testing warning the barco monitor...
Page 44
Windows 2000 barcomed 2mp2cp software installation 44 displays active. To make your mgp 15 or your displays active you must extend your desktop to these displays using the “windows display control panel”. If for some reason windows failed to correctly set the resolution of your mgp 15 or displays pl...
Page 45
45 display controller tools.
Page 46
Display controller tools 46 (this page intentionally left blank.).
Page 47
Barco display tab 47 barco display tab introduction the barco display tab is used for gathering information about the barcomed flat panel display(s). To access the barco display tab do the following: 1. Open the “display properties control panel” by right clicking on the desktop, then select “proper...
Page 48
Barco display tab 48 display properties you may access the properties page of the currently selected display, which is represented by the monitor icon above with the black frame around it, by either clicking on the “properties” button or double clicking on the icon. This screen (figure 20 on page 49...
Page 49
Barco display tab 49 figure 20
Page 50
Barco display tab c oronis 3mp (this page intentionally left blank.) 50
Page 51
Barcomed driver tab 51 barcomed driver tab introduction after the barcomed windows display controller driver is installed, a new display properties tab is available for configuring special features of the barcomed display controller. Languages supported the barcomed driver tab supports the following...
Page 52
Barcomed driver tab 52 figure 21: barcomed driver tab under windows 2000 and windows xp status the status section displays information about the current barcomed display controller, driver, and the currently selected display resolution. Graphics board this displays the current barcomed display contr...
Page 53
Barcomed driver tab 53 resolution this displays the currently selected display resolution. Monitor configuration if the options in this section are grayed out, then they are not available for the model controller with which you are working. For the barcomed 2mp2cp, the monitor configuration pull-dow...
Page 54
Barcomed driver tab c oronis 3mp (this page intentionally left blank.) 54.
Page 55
Barcomed hardware tab 55 barcomed hardware tab introduction the barcomed hardware tab is used for gathering information about barcomed display controller(s). For all barcomed display controller(s) it will display pci information. For barcomed display controller(s) based on the aura video chipset it ...
Page 56
Barcomed hardware tab 56 using the barcomed hardware tab to access the barcomed hardware tab do the following: 1. Open the “display properties control panel” by right clicking on the desktop, then select “properties”. 2. Click on the “settings” tab. Double click on the rectangle that represents one ...
Page 57
Barcomed hardware tab 57 figure 22 barcomed hardware tab under windows 2000 or windows xp device displays the current barcomed display controller, driver, and the currently selected display resolution. Information device id: displays the device’s pci device id number. Vendor id: displays the device ...
Page 58
Barcomed hardware tab 58 subsystem id: displays the device’s pci subsystem id number. Subsystemvendorid: displays the device’s pci subsystem vendor id number. Vga status: displays whether the vga capabilities of the barcomed controller are enabled or disabled. Firmware information product name: disp...
Page 59
Barcomed hardware tab 59 detailed customer contact information. After completion of the customer contact information screen, the wizard will then ask the user to provide a description of the problem, and prompt the user to enter the medical viewing applications that they are using. The wizard will t...
Page 60
Barcomed hardware tab 60 this screen gathers the diagnostic data from the user’s system as described above in this document. Click the “start diagnostic” button to begin the diagnostic gathering process. To perform the graphics operations test, check the graphics operations checkbox. During the grap...
Page 61
Barcomed hardware tab 61 3. Then click on “support” in the drop down menu. 4. Find the appropriate imagecare center for your country and click on the email link. 5. Enter a subject and a brief message describing the problem about which you are requesting help. 6. Attach the barcomed self exam report...
Page 62
Barcomed hardware tab 62.
Page 63
63 display tools.
Page 64
Display tools 64 (this page intentionally left blank.).
Page 65
Barco dpms screen saver 65 barco dpms screen saver introduction the barco dpms (display power management signaling) screen saver allows the user to set power and display saving features for medical displays controlled by barcomed display controllers. At the end of the work day, the display will ente...
Page 66
Barco dpms screen saver 66 save as saves your current barco dpms screen saver settings. The name you specify will appear in the scheme list so you can easily restore these settings later. Delete deletes the scheme that is selected in the scheme box. Work schedule in this part of the control panel th...
Page 67
Barco dpms screen saver 67 dpms settings after work day if you have an display controller that supports dpms calls, then you will be able to set the dpms settings for after the work day. Otherwise, a text box will be displayed telling you why dpms functions are not available. Amount of time in each ...
Page 68
Barco dpms screen saver 68 on barco c oronis displays, the i-guard will stabilize the image within a few seconds after the display returns to the active state so there is no need for a warm-up time period. Use as logon screen saver check the box to use the barco dpms screen saver when no one is logg...
Page 69
Barco dpms screen saver 69 including those who do not have administrator privileges, can create, modify or delete private schemes. When the delete button is pressed, the user is asked to confirm the delete request. Using the barco dpms screen saver using the barco dpms screen saver is similar to usi...
Page 70
Barco dpms screen saver 70 figure 24: windows xp screen saver tab 2. Click on the “settings” button. The “barco dpms screen saver control panel” will open (see figure 25 on page 70). Figure 25: barco dpms settings control panel.
Page 71
Barco dpms screen saver 71 3. Use the default schemes by selecting one of the three default schemes. Click “ok”. Then click “ok” again. Note: if you make any changes to any of the settings of one of the three default schemes, the current scheme field will blank and you must save your changes by clic...
Page 72
Barco dpms screen saver 72 4. Select one of the default schemes from the “current scheme” drop down menu. 5. Set the work schedule by setting the beginning and ending time of your work day for each day of the week. 6. Select the screen saver you wish to use during the work day in the “screen saver d...
Page 73
Barco dpms screen saver 73 and run the barcomed product install wizard (please see the section software installation for complete instructions). Special note: reinstalling the barco dpms screen saver will over write the dpms configuration settings and you will need to reconfigure the dpms settings o...
Page 74
Barco dpms screen saver 74 (this page intentionally left blank.).
Page 75
75 medical pro and dicom theater software.
Page 76
Medical pro and dicom theater software 76 (this page intentionally left blank.).
Page 77
Medical pro installation 77 medical pro installation install medical pro on the pc. Follow the instructions from the medical pro user guide. Important: do not forget you have to have administrator privileges to install or uninstall medical. During installation, you will have to indicate you are usin...
Page 78
Using medical pro 78 using medical pro after installation of the hardware and software, you must start medical pro. With medical pro, you can calibrate the display and projector, and start the projector stabilization. Proceed as follows: 1. Start medical pro. If appropriate, you can connect to medic...
Page 79
Using medical pro 79 8. For all the devices in the configuration, define (if necessary) and select a preset. 9. After selecting the preset, medical pro starts consistency calibration automatically. Please refer to the medical pro user guide for more information..
Page 80
Optical sensor connection 80 optical sensor connection the optical sensor can be attached to the screen by means of velcro, attached to the rear of the sensor. The sensor must be connected to the pc through usb. Note: when you plug in the optical sensor to the pc usb bus for the first time, you will...
Page 81
Optical sensor connection 81 sensor position and screen resolution a) selected resolution of 1280 x 1024 (1024 x 1280) figure 29 b) selected resolution of 1600 x 1200 (1200 x 1600) figure 30 active image 1280x1024 active image 1600x1200
Page 82
Using dicom theater software 82 using dicom theater software the dicom theater software tool has two purposes: the first goal is to stabilize the projector. In other words, this is to control the projector so that it continually conforms to the target situation as defined in the medical pro preset. ...
Page 83
Using dicom theater software 83 stopping and starting stabilization introduction stabilization starts automatically after the projector was calibrated from medical pro. The stabilization process can be stopped and restarted explicitly by the user using the dicom theater application. However, if the ...
Page 84
Using dicom theater software 84 restarting stabilization manually to restart the projector stabilization, proceed as follows: 1. Position the cursor over the dicom theater sys-tray icon and click the right mouse button (“right-click”). The dicom theater menu appears. Figure 33 2. Click start stabili...
Page 85
Controlling the projector 85 controlling the projector introduction the projector control provides quick access to some frequently used projector functionality, such as: • source selection: allows fast switching between projector inputs. Only inputs that have a valid input (a valid signal present at...
Page 86
Controlling the projector 86 4. Select the desired input source in the source selection section. Picture-in-picture selection to switch picture-in-picture layouts, proceed as follows: 1. Position the cursor over the dicom theater sys-tray icon and click the right mouse button (“right-click”). The di...
Page 87
Controlling the projector 87 projector control configuration under the configuration tab, the user can customize the names of the sources and projectors according to his/her best understanding. To modify the projector control configuration, proceed as follows: 1. Position the cursor over the dicom t...
Page 88
Controlling the projector 88 4. Change the names of the items appearing in the projector control view according to your own preferences. The changed names are used in the dicom theater application only, not in the projector’s on-screen display..
Page 89
Consulting projector properties 89 consulting projector properties with the properties, the user can query the projector for common information. All the properties displayed in this view are also accessible via the "information" section in the osd of the projector. To consult the projector propertie...
Page 90
Consulting projector properties 90 portrait/landscape: the projector’s current orientation front/rear-ceiling/ table: the projector’s current configuration projector address: the projector’s internal rs-232 address lamp runtime: the number of hours the projector lamp has been operating projector run...
Page 91
Troubleshooting the stabilization process 91 troubleshooting the stabilization process the projector stabilization has stopped unexpectedly possible causes: • no communication with projector. The projector may be switched off, removed, or the rs-232 cable may be disconnected at the projector’s or pc...
Page 92
Troubleshooting the stabilization process 92 (this page intentionally left blank.).
Page 93
93 troubleshooting.
Page 94
Troubleshooting 94 (this page intentionally left blank.).
Page 95
95 windows 2000 display resolution tip: these instructions apply to both windows ® 2000 and windows ® xp. Setting the resolution of your dicom theater display in order to set the resolution of your dicom theater display you must be logged in using an account with administrator privileges. 1. To set ...
Page 96
96 7. Click “yes” when asked, “your desktop has been reconfigured. Do you want to keep these settings?” to set the resolution of the second display attached to the barcomed display controller you are working with, go back to the “settings” tab of the “display properties control panel”. Attach the di...
Page 97
Driver re-installation, updates or removal 97 driver re-installation, updates or removal reinstalling or updating your barcomed 2mp2cp driver note: these instructions apply to windows 2000 and windows xp. Important for windows 2000 or windows xp users only: if you previously uninstalled the driver, ...
Page 98
Driver re-installation, updates or removal 98 3. To update the driver, clear the checkbox next to (figure 38) and click “install”. Figure 38 4. For windows 2000 or windows xp please turn to step 6 on page 38 in the section titled “windows 2000 barcomed 2mp2cp software installation” and follow the in...
Page 99
Driver re-installation, updates or removal 99 uninstalling the barcomed 2mp2cp driver 1. Insert your barcomed 2mp2cp software cd into your computer’s cd drive. If the “barcomed product installation wizard” doesn’t start within one minute, browse the contents of your dicom theater software cd and dou...
Page 100
Driver re-installation, updates or removal 100 figure 40 6. Click “next”. 7. If you installed your driver with dualview enabled, skip to step 8. If you installed your driver with cloned heads active, click “next” to continue. Then click “finish” to complete the uninstall process. Click “finish” agai...
Page 101
Driver re-installation, updates or removal 101 10. When your system restarts, log in again using an account with administrator priveleges. Dualview should now be disabled. 11. The “barcomed product installation wizard” should automatically restart. Finish uninstalling the driver by clicking “next” t...
Page 102
Www.Barco.Com b4100441 - 03 august 2004.