- DL manuals
- Barco
- Medical Equipment
- Nio medical display systems
- Installation & User Manual
Barco Nio medical display systems Installation & User Manual
Summary of Nio medical display systems
Page 1
Installation & user manual nio® medical display systems supported displays: e-2620, e-3620, e-5620, e-2621, e-3621.
Page 2
(this page intentionally left blank.) 2.
Page 3
Copyright notice 3 copyright notice this document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems...
Page 4
Copyright notice 4 (this page intentionally left blank.).
Page 5
Table of contents 5 table of contents preface........................................................................................ 9 safety instructions............................................................................. 13 explanation of symbols ............................................
Page 6
Table of contents 6 palette mode .............................................................................. 66 drawing modes .......................................................................... 68 monitor configuration ................................................................ 69 con...
Page 7
Table of contents 7 setting the resolution of your b arco m ed n io display ............. 117 driver re-installation, updates or removal..................................... 120 reinstalling or updating your barcomed nio driver ............... 120 uninstalling the barcomed nio driver or barco niowat...
Page 8
Table of contents (this page intentionally left blank.) 8.
Page 9
9 preface.
Page 10
Preface (this page intentionally left blank.) 10 (this page intentionally left blank.).
Page 11
Preface 11 notice although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable documentation possible; if you discover errors, please let us know. Barcoview ...
Page 12
Preface 12 canadian notice this class a digital apparatus complies with canadian ices-003. Cet appareil numérique de la classe a est conforme à la norme nmb-003 du canada. Disposal information the lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as requi...
Page 13
Safety instructions 13 safety instructions general recommendations read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instru...
Page 14
Safety instructions 14 • power cords: power cord with cee 7 plug: the colors of the mains lead are colored in accordance with the following code: green-and-yellow: earth (safety earth), blue: neutral, brown: line power cord with ansi 73.11 plug: the wires of the power cord are colored in accordance ...
Page 15
Safety instructions 15 operating precautions continuous operation of the display with the same screen may result in some image sticking on the lcd panel. Over 10 hours operation with the same image content is not recommended. Switching on the display dpms may decrease the risk of image sticking (ima...
Page 16
Explanation of symbols 16 explanation of symbols symbols on the display and power supply on the display or power supply, you may find the following symbols: symbols used throughout the manual: indicates the display is approved according to the ce regulations or indicates the display is approved acco...
Page 17
17 overview.
Page 18
Overview (this page intentionally left blank.) 18 (this page intentionally left blank.).
Page 19
Introduction 19 introduction thank you for choosing barco. Single display or complete system? This manual describes installation and usage of a complete n io system. A n io system is a bundling of one or more displays and one or more display controllers. However, if you have purchased the display on...
Page 20
Introduction 20 niowatch in n io systems, the display comes standard with n io w atch , a user-friendly software tool that optimizes the lcd panel for dicom-compliant viewing. Power saving the displays are equipped with a power saving system. When left idle for a certain time, the computer connected...
Page 21
Barcomed nio display controller overview 21 barcomed nio display controller overview the barcomed nio display controller delivers a quality image with 256 simultaneous shades of gray for medical viewing applications. Minimum system requirements • pentium ii 266 mhz with 128 mb ram (pentium ii 800mhz...
Page 22
Barcomed nio display controller overview 22 for barcomed nio 3mp • 1536 x 2048 @ 60 hz (primary) • 2048 x 1536 @ 60 hz for barcomed nio 5mp • 2048 x 2560 @ 60 hz (primary) • 2560 x 2048 @ 60 hz for all barcomed nio display controllers the following resolution is also available when the os is booted ...
Page 23
Package contents 23 package contents nio system package each n io system contains one or more display boxes (see below) and a system accessory box containing the following items: • display controller(s) • cd-rom with driver, niowatch software and documentation display box each display box includes o...
Page 24
Parts, controls and connectors 24 parts, controls and connectors front figure 1: front side 1. Power led the led is off when the display is disconnected from the power. The led is also off when the led function is disabled in the on-screen display (osd). The led is green when the display is on (when...
Page 25
Parts, controls and connectors 25 rear figure 2: rear side 1. Connector compartment cover to get access to the connectors, remove the cover by pulling down the 2 clips at the top of the cover. 2. Tilt & swivel foot cover this cover is packed in a separate box when the display is shipped to the custo...
Page 26
Parts, controls and connectors 26 8. Dc power input connect the external power supply, delivered with the display, to this connector. 9. Tilt & swivel foot clip the display is shipped with this clip in the foot to protect the tilt & swivel mechanism during transport. After unpacking, you should remo...
Page 27
27 installation.
Page 28
Installation (this page intentionally left blank.) 28 (this page intentionally left blank.).
Page 29
Installation precautions 29 installation precautions precautions • keep your original packaging. It is designed for this display and is the ideal protection during transport. • avoid reflections in the flat panel to reduce eye strain. • place the display on a strong and stable table or desk. • keep ...
Page 30
Display controller installation 30 display controller installation caution: wear a grounded, protective esd strap during installation or handling of the display controller. Electrostatic charges can damage the display controller. Prior to installing your barcomed nio display controller(s) in your pc...
Page 31
Display controller installation 31 figure 4 if you decide to use a separate vga monitor as your boot monitor, you must disable the barcomed nio’s on-board vga capabilities by moving the jumper to the bottom two pins. Caution: to use multiple barcomed nio controllers in a single host with vga enabled...
Page 32
Display controller installation 32 figure 5: pci and raid controller slots installing the barcomed nio display controller install the barcomed nio controller in your computer following these steps: 1. Turn off the power to your computer and disconnect the power cord, however make sure that the compu...
Page 33
Display controller installation 33 6. Connect the primary display to the connector marked “vid 1” on the barcomed nio display controller using the provided dvi cable (see figure 6 below). For a dual-headed barcomed nio setup, connect the secondary display to the other connector on the display contro...
Page 34
Display installation 34 display installation after unpacking the display important: in the factory, the height-positioning system in the display foot is blocked with a red clip to prevent damage during transportation. Before installing the display, you must remove this clip. Figure 7 to remove the c...
Page 35
Display installation 35 adjust the panel orientation you can change the orientation of the panel at any time, but it is more convenient to select landscape or portrait orientation before connecting the cables. To change the panel orientation: 1. Stand at the front side of the panel and take the pane...
Page 36
Display installation 36 figure 10: tilt the panel before rotating 3. To change from portrait to landscape, turn the panel counterclockwise. Figure 11: to rotate the panel from portrait to landscape 4. To change from landscape to portrait, turn clockwise. Notice: if, after installing the display or t...
Page 37
Display installation 37 • in a complete n io system, the image orientation will adapt to the new panel orientation automatically after a second. • if you would use the display without the n io display controller board, the image orientation will not change with the panel orientation. To change the o...
Page 38
Display installation 38 2. Connect the output of the 12v dc power supply to the dc input of the display. 3. Connect one end of the proper power cable to the ac input of the 12v dc power supply. 4. Connect the other end of the power cord to a grounded power outlet. Video connection connecting dvi cab...
Page 39
Display installation 39 usb connection the usb connection allows you to use the display as usb hub, to which you can connect usb devices, such as a keyboard, mouse or digital camera. To connect the usb cable: figure 15 1. Connect a pc usb downstream connector to the display’s usb upstream connector ...
Page 40
Display installation 40 • bind the cables together above and under the foot, by means of the 2 velcro strips attached to the inside of the foot cover (packed inside the accessory box). • at last, put the foot cover back in place. To put the foot cover in place: figure 16 1. Push the upper side of th...
Page 41
Attaching the display to an arm stand 41 attaching the display to an arm stand the panel, standard attached to the tilt & swivel foot, is compatible with the vesa 100 mm standard. So it can be used with an arm stand according to the vesa 100 mm standard. Therefore, the tilt & swivel foot must be rem...
Page 42
Attaching the display to an arm stand 42 6. Remove the four screws fixing the foot while supporting the foot. 7. Attach the arm stand firmly to the panel using 4 screws m4 x 8 mm. Figure 18 4 screws m4 x 8mm.
Page 43
Windows 2000 barcomed nio software installation 43 windows 2000 barcomed nio software installation note: these instructions apply to both windows ® 2000 and windows ® xp. Preparation prior to installing your b arco m ed n io software the following should be done. 1. Install the barcomed nio display ...
Page 44
Windows 2000 barcomed nio software installation 44 using the barcomed product installation wizard to install your barcomed nio windows display controller driver and niowatch software for the first time follow the steps below. If you are reinstalling the drivers or installing a new driver release ove...
Page 45
Windows 2000 barcomed nio software installation 45 figure 19 if it determines that the microsoft installer is either out of date or missing, it will display the screen shown in figure 20 below. Click “ok” to continue, the wizard will then install a newer version of the microsoft installer. Figure 20...
Page 46
Windows 2000 barcomed nio software installation 46 hardware wizard - video controller”. Again, please be patient as windows will again scan its library of plug-and- play device drivers to see if it has a driver for your barcomed nio controller. The barcomed software install wizard will automatically...
Page 47
Windows 2000 barcomed nio software installation 47 your barcomed software cd. Select the device you want to install and then click “next”. Note: if there are no barcomed devices installed, or if windows does not recognize the installed devices, or if the driver on your barcomed software cd does not ...
Page 48
Windows 2000 barcomed nio software installation 48 figure 23 click “ok” to install the new driver. If you don’t want to replace the exiting driver, click “ok” and then click “cancel”. 7. Your selection on the "enable dualview" screen (figure 24 below) determines if dualview is enabled or not. Dualvi...
Page 49
Windows 2000 barcomed nio software installation 49 figure 25: dualview disabled–rectangle 2 represents the combined heads of the barcomed controller. Figure 26: dualview enabled–rectangles 2 & 3 represents the individual heads of the barcomed controller. Special note: if you installed the drivers wi...
Page 50
Windows 2000 barcomed nio software installation 50 adapters" in the "device manager control panel". The second device will be disabled. This is normal. Do not try to enable any of the disabled display adapters. 8. The “device confirmation” screen displays the device driver that will be installed and...
Page 51
Windows 2000 barcomed nio software installation 51 figure 28: windows xp windows logo testing warning 10. When the screen shown in figure 29 below appears select the palette mode which is the correct one for your viewing application. If you are uncertain use the default settings. You can change the ...
Page 52
Windows 2000 barcomed nio software installation 52 figure 29 when the driver install wizard tells you that it has successfully installed the selected driver, click “finish”. The wizard will now begin installing the next selected piece of barcomed software. If you are working with the default selecti...
Page 53
Windows 2000 barcomed nio software installation 53 driver. The wizard will also begin to install the next selected piece of barcomed software. If the wizard failed to successfully install the selected driver, it will warn you that the installation failed. Click “finish” to return to the barcomed pro...
Page 54
Windows 2000 barcomed nio software installation 54 4. Click “next” on the select program folder screen to install the niowatch software in the default location. Or select one of the folders in the existing folders dialog window. While the wizard is installing niowatch, it will display a setup status...
Page 55
Windows 2000 barcomed nio software installation 55 figure 31: windows 2000 digital signature not found warning figure 32: windows xp windows logo testing warning the barco monitor plug and play software should automatically set the resolution for the displays of your barcomed nio system. It may be n...
Page 56
Windows 2000 barcomed nio software installation 56 panel”. If for some reason windows failed to correctly set the resolution of your displays please turn to the section “setting the resolution of your b arco m ed n io display” on page 117 of the troubleshooting section of this manual for instruction...
Page 57
Niowatch 57 niowatch barcomed niowatch installation 1. Click “next” on the welcome screen of the barco niowatch installshield wizard (figure 33) to begin the installation or click “cancel” to cancel and return to the barcomed product install wizard. 2. After reading the software license agreement on...
Page 58
Niowatch 58 6. When the installshield wizard complete screen appears click “finish”. 7. Click “finish” on the barcomed product installation screen to complete the install process. Note: silent mode installation you can install niowatch in silent mode on a system where no previous version of niowatch...
Page 59
59 display controller settings.
Page 60
Display controller settings (this page intentionally left blank.) 60 (this page intentionally left blank.).
Page 61
Barco display tab 61 barco display tab introduction the barco display tab is used for gathering information about the barcomed flat panel display(s). To access the barco display tab do the following: 1. Open the “display properties control panel” by right clicking on the desktop, then select “proper...
Page 62
Barco display tab 62 using the barco display tab displays all of the available display adapters that are of the same type as the current barco display adapter are shown here graphically, with one display icon representing each port of a display adapter. The icon orientation reflects the display reso...
Page 63
Barco display tab 63 backlight runtime: this is time in hours that the back light has been on. A common question is: how much longer will the backlight last? The backlight will typically last a very long time, but will only be able to hold a calibrated output of for 17000 hours, after which time it ...
Page 64
Barcomed driver tab 64 barcomed driver tab introduction after the barcomed windows display controller driver is installed, a new display properties tab is available for configuring special features of the barcomed display controller. Languages supported the barcomed driver tab supports the following...
Page 65
Barcomed driver tab 65 figure 36: barcomed driver tab under windows 2000 and windows xp status the status section displays information about the current barcomed display controller, driver, and the currently selected display resolution. Graphics board this displays the current barcomed display contr...
Page 66
Barcomed driver tab 66 resolution this displays the currently selected display resolution. Palette mode in the palette mode section you can choose one of the four following palette modes.If you are using a color display in conjunction with your barco grayscale display(s) under windows 2000 or window...
Page 67
Barcomed driver tab 67 windows operating system, but applications can manipulate the middle 236 entries. This is the standard palette mode as configured by windows. Figure 37 static gray palette including standard system colors this option sets the palette to be a static set of 256 gray values. Ther...
Page 68
Barcomed driver tab 68 static gray palette with no system colors this option sets the palette to be a static linear ramp of 256 shades of gray. Therefore, applications are denied the ability to dynamically change or allocate palette entries. This prevents palette conflicts between applications, whic...
Page 69
Barcomed driver tab 69 enable directdraw this option allows the user to enable or disable directdraw. Directdraw is a software interface that provides direct access to display devices while maintaining compatibility with the windows graphics device interface (gdi). Directdraw provides a device-indep...
Page 70
Barcomed driver tab 70 configuring the windows 2000 or windows xp desktop important: if you are using a color display in conjunction with your barco grayscale display(s) you should configure your desktop before setting the resolution of the your barco grayscale display(s). Under windows 2000 or wind...
Page 71
Barcomed driver tab 71 examples (your resolution settings may be different): ok to use: display 1 2480 x 2560 @ 59 hz display 2 2480 x 2560 @ 59 hz not ok to use display 1 2480 x 2560 @ 59 hz display 2 2560 x 2480 @ 59 hz the following options maybe set individually on each barco display even if the...
Page 72
Barcomed hardware tab 72 barcomed hardware tab introduction the barcomed hardware tab is used for gathering information about barcomed display controller(s). For all barcomed display controller(s) it will display pci information. For barcomed display controller(s) based on the aura video chipset it ...
Page 73
Barcomed hardware tab 73 using the barcomed hardware tab to access the barcomed hardware tab do the following: 1. Open the “display properties control panel” by right clicking on the desktop, then select “properties”. Barcomed 3mp2fh pci and firmware information barcomed 5mp1h pci information only b...
Page 74
Barcomed hardware tab 74 figure 40 barcomed hardware tab under windows 2000 or windows xp device displays the current barcomed display controller, driver, and the currently selected display resolution. Identify device: this button is for barcoview medical imaging systems (mis) internal use only and ...
Page 75
Barcomed hardware tab 75 pci information device id: displays the device’s pci device id number. Vendor id: displays the device manufacturer’s pci vendor id number. Subsystem id: displays the device’s pci subsystem id number. Subsystemvendorid: displays the device’s pci subsystem vendor id number. Vg...
Page 76
Barcomed hardware tab 76 problem. It probes the system for various types of system information, and saves it to a web-page report that can then be analyzed by the barco imagecare team. Barcomed self exam is implemented in a wizard format. The barcomed self exam wizard will first ask the user to prov...
Page 77
Barcomed hardware tab 77 gathering diagnostic data screen important: when performing the graphics operations, you must drag the "gathering diagnostic data screen" onto the display for which you want the graphics operations data. This screen gathers the diagnostic data from the user’s system as descr...
Page 78
Barcomed hardware tab 78 customer support organization by email. To do this you need a system with access to the world wide web. 1. Enter the following address in your web browser’s address bar: http://www.Barco.Com/medical/ 2. In the left hand column click on “contact us” 3. Then click on “support”...
Page 79
Barcomed hardware tab 79 update device... Button: clicking this button will launch the barcomed hardware configuration utility. This program allows the user to flash update the firmware stored in the rom of the currently selected barcomed display controller. The barcomed hardware.
Page 80
Barcomed hardware tab 80 configuration utility is implemented in a wizard format, which guides the user through the flash update procedure. The user will be prompted to select a firmware update file to use for the update process. This file will be provided by barcoview mis if and when a firmware upd...
Page 81
81 niowatch operation.
Page 82
Niowatch operation (this page intentionally left blank.) 82 (this page intentionally left blank.).
Page 83
Niowatch operation 83 to use niowatch the niowatch application resides in the windows systray. To use one of the niowatch functions, right-click on the niowatch systray icon and select the appropriate option: figure 41: niowatch systray icon note: after installation, a shortcut “niowatch client” is ...
Page 84
Display settings 84 display settings general figure 43: display settings dialog the numbered icons in the upper part of the dialog represent the display controller heads supported by niowatch. The display controller heads are also listed in the display drop- down box. If you wish to control a displa...
Page 85
Display settings 85 numbered icon or by selecting the corresponding display controller head from the display drop-down box. Tip: if you click on a numbered icon, the corresponding number appears for a few seconds on the display connected to that display controller head. In that way you can easily se...
Page 86
Display settings 86 • to adjust display luminance manually, adjust the luminance slider. This function is not available for mfcd/mfgd 1218 displays. The luminance setting is saved when the system is shut down. If the slider is positioned above the cal mark, the luminance is in calibrated position, a...
Page 87
Display settings 87 graphic board tab figure 44: graphic board tab here you can see information about the installed display controller: name, serial number, driver version and firmware version..
Page 88
Display settings 88 calibration tab figure 45: calibration tab here you can calibrate display(s), revert to the latest calibration, revert to default factory settings and view the result of the latest calibration. The possible options are explained below. To calibrate the display using the barco lcd...
Page 89
Display settings 89 option in the application settings dialog is set. See “calibration tab” in the description of the application settings dialog. 2. If you have multiple displays connected (multi-head system), select the display you wish to calibrate by clicking on the corresponding numbered icon i...
Page 90
Display settings 90 figure 47: match with reference to equalize the display, check the option “match this display with display....” and click next. The display number that appears in this option, refers to the reference display. Manual calibration 1. Follow step 2 and 3 of the calibration with barco...
Page 91
Display settings 91 figure 48: dicom optimizer dialog 3. Adjust the slider until there is almost no visible difference between the background of the image above the slider and the bitmap inside this image. 4. When done, click button set point 1 of 20. 5. Repeat this procedure until the button is gra...
Page 92
Display settings 92 3. Click the ok button. The calibration and the luminance will be reset to the latest calibrated position. Note: when you start up the system, the calibration is also reset to the latest calibrated position. The luminance, however, is kept at the latest value. To view a graph sho...
Page 93
Test patterns 93 test patterns test patterns figure 49: test patterns dialog 1. Select the desired test pattern by clicking on the corresponding thumbnail or selecting a pattern by name from the test pattern drop-down box. 2. Click show to display the pattern. If you have selected custom image, you ...
Page 94
Application settings 94 application settings calibration tab figure 50: calibration tab here you can check the equalization option, allowing you to match all the displays from a multi-head system to the luminance of the first calibrated display of the system. Suppose you work with a system containin...
Page 95
Application settings 95 • the system contains at least one display of the same type as the one being calibrated • at least one of the displays of the same type has already been calibrated before using a sensor. To equalize the displays: 1. Be sure the reference display is calibrated to the desired l...
Page 96
Application settings 96 the user-friendly web interface, accessible from any client, users have access to all the information of the installed display base. For more information about medical administrator, please contact barco medical imaging systems or consult our web site..
Page 97
Update niowatch 97 update niowatch in the windows start menu, the update niowatch application is installed during installation of niowatch. To update niowatch: select update niowatch from the start > programs > barco niowatch menu. The application will search via the internet if niowatch updates are...
Page 98
Update niowatch (this page intentionally left blank.) 98.
Page 99
99 display operation.
Page 100
Display operation (this page intentionally left blank.) 100 (this page intentionally left blank.).
Page 101
Display operation 101 display operation operating precautions continuous operation of the display with the same screen may result in some image sticking on the lcd panel. Over 10 hours operation with the same image content is not recommended. Switching on the display dpms may decrease the risk of im...
Page 102
Display operation 102 about the on-screen display (osd) about the on-screen display the on-screen display (osd) has a hierarchical tree structure, with several levels. The top level is the “main menu”. Figure 54: main menu how to navigate through the osd 1. When the osd is not on the screen, rotate ...
Page 103
Display operation 103 3. To exit from a menu, rotate the control wheel to select exit. If you exit from the main menu, you exit the osd. 4. To change an adjustment value (e.G., the luminance value), rotate the control wheel to select the adjustment and press the wheel shortly. The adjustment name ap...
Page 104
Display operation 104 4. Rotate the control wheel to select user controls. 5. Press the control wheel to switch from “on” to “off”. 6. Exit the menus. To enable user controls: 1. Do not use the control wheel for at least 3 seconds. 2. Rotate the control wheel 1 step clockwise. 3. Press the control w...
Page 105
Display operation 105 complete osd overview main menu luminance luminance adjusts the overall luminance (light output) of the display. It does not affect the grayscales of the image on the screen. Name description luminance adjust the target luminance to which the dis- play will be stabilized. Setti...
Page 106
Display operation 106 settings information name description dpms switch on/off the automatic power saving sys- tem (dpms) power led switch the power led on/off. Note: the led's orange dpms state is not influenced by this set- ting. So, when the display goes into power-sav- ing mode, the led will tur...
Page 107
107 cleaning.
Page 108
Cleaning (this page intentionally left blank.) 108 (this page intentionally left blank.).
Page 109
Cleaning 109 precautions • take care not to damage or scratch the glass or lcd panel. • do not apply pressure on the glass or lcd panel. • do not apply or spray liquid directly to the glass, panel or cabinet as excess liquid may cause damage to internal electronics. Instead, apply the liquid to the ...
Page 110
Cleaning 110 removal of dust particles and other dry contaminants on the surface of the lcd panel or the glass panel. Attention: the dust remover contains a liquid gas. If you shake the can or move the can too fast while spraying, you may blow drops of liquid on the panel surface! If this is the cas...
Page 111
111 troubleshooting.
Page 112
Troubleshooting (this page intentionally left blank.) 112 (this page intentionally left blank.).
Page 113
Troubleshooting 113 general tips • if one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power supplies. In that way you can find out if the problem resides in the display or not..
Page 114
Troubleshooting 114 problems and solutions problem description possible tests or solutions screen remains black • please check the installation procedure in this manual • if the led at the front is orange, the display is in stand-by • check in the windows display properties if the display controller...
Page 115
Troubleshooting 115 no image during pc start- up • check the vga jumper settings on the display controller • check the cmos settings in the pc bios nothing happens when you press or rotate the control wheel • the user controls may be disabled. Please read the paragraph about the “user controls” func...
Page 116
Troubleshooting 116 windows 2000 display resolution tip: these instructions apply to both windows ® 2000 and windows ® xp. Important: if you are using a color display in conjunction with your barco grayscale display(s) you should configure your desktop before setting the resolution of the your barco...
Page 117
Troubleshooting 117 setting the resolution of your b arco m ed n io display in order to set the resolution of your b arco m ed n io display you must be logged in using an account with administrator privileges. 1. To set the resolution of your barcomed nio display(s) right click on the desktop and se...
Page 118
Troubleshooting 118 controller, you may need to temporarily make another display the primary display caution: if you have a single display configuration and you have enabled dualview, windows will not allow you to attach the second head. This is normal and not a bug. 4. For the display which is stil...
Page 119
Troubleshooting 119 the display you detached in step 2 above, by right clicking on the rectangle that represents it and selecting “attached”. Now repeat steps 5-8 above for this display. If you are using a quad-head configuration repeat all of the above steps for the two displays on the second displ...
Page 120
Driver re-installation, updates or removal 120 driver re-installation, updates or removal reinstalling or updating your barcomed nio driver note: these instructions apply to windows 2000 and windows xp. Important for windows 2000 or windows xp users only: if you previously uninstalled the driver, do...
Page 121
Driver re-installation, updates or removal 121 3. To update the driver, clear the checkbox next to “niowatch setup” (figure 60) and click “install”. Figure 60 4. For windows 2000 or windows xp please turn to step 6 on page 4 in the section titled “windows 2000 barcomed nio software installation” and...
Page 122
Driver re-installation, updates or removal 122 doesn’t start within one minute, browse the contents of your barcomed nio software cd and double click on the file: “setup.Exe” to start the wizard. 2. The barcomed product installation wizard will display its welcome screen. 3. Make certain that the ch...
Page 123
Driver re-installation, updates or removal 123 figure 62 6. Click “next”. 7. If you installed your driver with dualview enabled, skip to step 8. If you installed your driver with dualview disabled, click “next” to continue. Then click “finish” to complete the uninstall process. Click “finish” again ...
Page 124
Driver re-installation, updates or removal 124 10. When your system restarts, log in again using an account with administrator priveleges. Dualview should now be disabled. 11. The “barcomed product installation wizard” should automatically restart. Finish uninstalling the driver by clicking “next” t...
Page 125
125 technical information.
Page 126
Technical information (this page intentionally left blank.) 126 (this page intentionally left blank.).
Page 127
Technical specifications 127 technical specifications e- 2620: item specification picture panel 19.6-inch diagonal viewable screen tft (thin film transistor) active matrix, gray- scale liquid crystal display resolution native: 1600 x 1200 display area (h x v) 398.4 x 298.8 (mm) viewing angle (@ 10/1...
Page 128
Technical specifications 128 power source input for 12 vdc power supply unit: 90 ~ 264 vac input for display: 12 vdc. (the supplied 12vdc power supply must be used) power consumption 66 watts (max., at 90 vac, maximum backlight, usb load) dimensions (w x h x d) in perpendicular vertical position, hi...
Page 129
Technical specifications 129 e- 2620 (s): item specification picture panel 20.1-inch diagonal viewable screen tft (thin film transistor) active matrix, gray- scale liquid crystal display resolution native: 1600 x 1200 display area (h x v) 408 x 306 (mm) viewing angle (@ 10/1 contrast) vertical: 170º...
Page 130
Technical specifications 130 input signals possible resolutions: • 640 x 480 @ 60, 75, 85, 100 hz • 800 x 600 @ 60, 75, 85, 100 hz • 1024 x 768 @ 60, 75, 85, 100 hz • 1152 x 864 @ 75 hz • 1152 x 870 @ 60, 85, 100 hz • 1024 x 1280 @ 59, 70 hz • 1280 x 1024 @ 60, 75, 85 hz • 1600 x 1200 @ 59, 60 hz • ...
Page 131
Technical specifications 131 e- 2621: item specification picture panel 21.3-inch diagonal viewable screen tft (thin film transistor) active matrix, gray- scale liquid crystal display resolution native: 1600 x 1200 display area (h x v) 432.0 x 324.0 (mm) viewing angle (@ 10/1 contrast) vertical: 170º...
Page 132
Technical specifications 132 power source input for 12 vdc power supply unit: 90 ~ 264 vac input for display: 12 vdc. (the supplied 12vdc power supply must be used) power consumption 66 watts (max., at 90 vac, maximum backlight, usb load) dimensions (w x h x d) in perpendicular vertical position, hi...
Page 133
Technical specifications 133 e-3620: item specification picture panel 20.8-inch tft am-lcd ips dual domain resolution native: 2048 x 1536 display area (h x v) 423.9 x 318 (mm) viewing angle (@ 10/1 contrast) vertical: 170º horizontal: 170º pixel pitch 0.207 mm (h) x 0.207 mm (v) native color resolut...
Page 134
Technical specifications 134 dimensions (w x h x d) in perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm net weight 13 kg operating temperature 0°c to 40°c, 15°c to 35°c within specs storage temperature -20°c to 60°c humidity 8% - 80% (non-condensing) for ...
Page 135
Technical specifications 135 e-3621: item specification picture panel 21.3-inch tft am-lcd ips dual domain resolution native: 2048 x 1536 display area (h x v) 433.2 x 324.9 (mm) viewing angle (@ 10/1 contrast) vertical: 170º horizontal: 170º pixel pitch 0.2115 mm (h) x 0.2115 mm (v) native color res...
Page 136
Technical specifications 136 e-5620: dimensions (w x h x d) in perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm net weight 14 kg operating temperature 0°c to 40°c, 15°c to 35°c within specs storage temperature -20°c to 60°c humidity 8% - 80% (non-condensi...
Page 137
Technical specifications 137 signal systems video on dvi: complying to dvi rev 1.0 specifications sync on dvi: complying to dvi rev 1.0 specifications usb standard supported usb 1.1 power source input for 12 vdc power supply unit: 90 ~ 264 vac input for display: 12 vdc. (the supplied 12vdc power sup...
Page 138
Connector pin assignments 138 connector pin assignments dvi connector: figure 64: dvi connector pin layout pin no. Signal pin no. Signal 1 tmds data 2- 14 +5v power 2 tmds data 2+ 15 gnd 3 gnd 16 hot plug detect 4 nc 17 tmds data 0- 5 nc 18 tmds data 0+ 6 ddc clock 19 gnd 7 ddc data 20 nc 8 nc 21 nc...
Page 139
Glossary 139 glossary calibration each display is calibrated in the factory before it is sent to the customer. After this calibration, black and white luminance are set to the ideal level. A stabilization routine, constantly active when the display is on, keeps these levels constant using the built-...
Page 140
Glossary (this page intentionally left blank.) 140
Page 141
141 warranty statement.
Page 142
Warranty statement (this page intentionally left blank.) 142 (this page intentionally left blank.).
Page 143
Warranty statement 143 article 1: services barcoview warrants that the equipment will be free of defects in workmanship or material for the warranty period. Notwithstanding the provisions of clause 2, repair and replacement of defects in material and/or workmanship under this warranty shall be accom...
Page 144
Warranty statement 144 article 2: items excluded from warranty the warranty described herein shall not include the following: 2.1 any hardware or software item procured from a source other than barcoview or their official agent or distributor and integrated by customer or a third party into barcovie...
Page 145
Warranty statement 145 obligations under this paragraph shall excuse barcoview's performance hereunder: 3.1 customer shall not expose barcoview personnel to any unsafe working conditions. 3.2 repairs to equipment under warranty resulting from improper maintenance or repair performed by the customer,...
Page 146
Warranty statement 146 products or services covered by or furnished under this warranty condition, whether arising out of contract, negligence, strict tort, warranty or otherwise, shall not exceed the price of the item or items of goods or services upon which such liability is based. Article 7: forc...
Page 147
Www.Barco.Com b4100454 - 00 march 2005.