- DL manuals
- Barco
- Projector
- R1306981K(R12)
- Installation Manual
Barco R1306981K(R12) Installation Manual
Summary of R1306981K(R12)
Page 1
Barco projection systems date: 29.05.2001 installation manual replacement of the dlp uhb (engine) in the elm series projectors r1306981k(r12) r1306991k(g10) art. No.: r5976199 rev: 00 k it e ngine elm.
Page 2
Due to constant research, the information in this manual is subject to change without notice. Produced by barco nv, may 2001. All rights reserved. Trademarks are the rights of their respective owners. Barco n.V./projection systems noordlaan 5 b-8520 kuurne belgium tel : +32/56/368211 fax : +32/56/35...
Page 3
Barco 3 projection systems service and assembly warnings who this installation must be performed by authorized technical personnel only, trained concerning ultraviolet radiation and electrical shock hazards and protective measures described on this note. General cau...
Page 4
Barco 4 projection systems contents of the kit kit contents the kit contains the following items : art. No description quantity art. No description quantity r1306981 dlp sxga uhb (r12) 1 or r1306991 dlp xga uhb (g10) 1 r5976199 man ins g10/r12elm engine 1 illustrati...
Page 5
Barco 5 projection systems removing the top and side projector covers what has to be done to access the engine the top and the side projector covers have to be removed. Necessary tools screwdriver 5 mm - allen key 5mm warning ! Refer to service and assembly warnings...
Page 6
Barco 6 projection systems removing the top and side projector covers (continued) illustrations image 2 removing the side covers to remove side covers, follow the next procedure: 1 2 3 1 1 3 on the signal input side of the projector, turn the indicated bolts (a) a q...
Page 7
Barco 7 projection systems access to the engine module what has to be done the studs and crossbar above the formatter box and the cover of the box itself have to be removed to access the module necessary tools small screw driver flat-blade 4.5mm removing the studs t...
Page 8
Barco 8 projection systems access to the engine (continued) removing the formatter box cover to remove the formatter box cover, follow the next procedure: 1 2 3 4 1&2 2 1 loosen the 6 spring screws (a) fastening the box cover to frame. Remove the bolt (b) fixating t...
Page 9
Barco 9 projection systems access to the engine (continued) illustration location of the engine (right view of the projector) image 3 remark depending on the projector the picture may not always coincide with the reality (metallic frame slightly different etc,...). ...
Page 10
Barco 10 projection systems formatter module disconnection what has to be done the 3 flex foil connectors have to be removed from the module. Warning take all necessary precautions while handling the static-sensitive formatter module. Removing the connectors to remo...
Page 11
Barco 11 projection systems removing the cables what has to be done the remaining cables connected to the engine have to be removed. Necessary tools none to be continued on next page removing the studs to remove those cables, follow the next procedure: 1 2 3 1 2&3 4...
Page 12
Barco 12 projection systems removing the cables (continued) illustrations picture 4 c.
Page 13
Barco 13 projection systems removing the engine what has to be done the engine has to be removed. To be continued on next page necessary tools hexagon ball driver 2.5 or l-shaped driver (2.5) + pliers removing the engine to remove the engine, follow the next procedu...
Page 14
Barco 14 projection systems removing the engine (continued) illustrations c d image 5 image 3 d image 4 f a b.
Page 15
Barco 15 projection systems mounting the engine to be continued on next page removing the engine to remove the engine, follow the next procedure: 1 2 3 4 1 1 2&3(next page) 4(next page) unpack gently the engine and put it on a table loosen the 3 screws and remove th...
Page 16
Barco 16 projection systems mounting the engine (continued) illustrations image 3 image 2 a b image 4.
Page 17
Barco 17 projection systems formatter module connection what has to be done the formatter module has to be connected to the engine. Warning take all necessary precautions while handling the static-sensitive formatter module. To be continued on next page connection o...
Page 18
Barco 18 projection systems formatter module connection (continued) d image 2 c illustrations b image 3 !.
Page 19
Barco 19 projection systems replacing the cables what has to be done the remaining cables have to be connected to the engine. Necessary tools none to be continued on next page connecting the cables to connect these cables, follow the next procedure: 1 2 3 1 2 3&4(ne...
Page 20
Barco 20 projection systems replacing the cables (continued) illustrations picture 4 c picture 3.
Page 21
Barco 21 projection systems centering the image in the light path (if necessary). What has to be done the postion of the folding mirror has to be aligned to center the projected image in the light path. Necessary tools hexagon ball driver 2.5mm positioning the foldi...
Page 22
Barco 22 projection systems reassembling the projector parts what has to be done the parts removed to have access to the engine have to be reinstalled. Reassembling to reinstall the removed parts, follow the next procedure (referred to pages where the described acti...