Summary of R9001290
Page 1
R9001290 owner's manual vision 9200
Page 3: Barco Projection Systems
Barco projection systems date : 280497 art. No. : r5975338 r9001290 owner's manual vision 9200 rev : 01.
Page 4
Due to constant research, the information in this manual is subject to change without notice. Produced by barco nv, april 1997. All rights reserved. Trademarks are the rights of their respective owners. Printed in belgium barco nv/projection systems noordlaan 5 b-8520 kuurne belgium printed in belgi...
Page 5: Table of Contents
Table of contents i-1 5975338 barcovision 9200 280497 table of contents i table of contents ................................................................................................................................................................... I-1 safety instructions .......................
Page 6
Table of contents i-2 5975338 barcovision 9200 280497 gain adjustment per color ..................................................................................................................................................... 9-2 smoothness ..........................................................
Page 7: Safety Instructions
Safety instructions 1-1 5975338 barcovision 9200 210497 1 safety instructions projectors are built in accordance with the requirements of the international safety standards iec950, ul 1950 and csa c22.2 no. 950, which are the safety standards of information technology equip- ment including electrica...
Page 8
Safety instructions 1-2 5975338 barcovision 9200 210497 remarque sur la sécurité les projecteurs sont fabriqués conformément aux exigences des normes de sécurité internationales iec950, ul 1950 et csa c22.2 no. 950. Ces normes de sécurité sont imposées aux équipements de la technologie informatique ...
Page 9
Safety instructions 1-3 5975338 barcovision 9200 210497 * do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. * to disconnect the cord, pull it out by the plug. Never pull the cord itself. * if an extension cord is used with this product, ...
Page 10
Safety instructions 1-4 5975338 barcovision 9200 210497 * ne rien laisser en appui sur le cordon d’alimentation. Ne pas placer ce cordon là où des personnes risques de marcher dessus. * pour débrancher le cordon, le tirer par le connecteur, jamais par le cordon lui-même. * si on utilise une rallonge...
Page 11: Unpacking And Dimensions
Unpacking and dimensions 2-1 5975338 barcovision 9200 210497 27.1 1125.7 630 42 2. 18 70 20 8. 6 150 702.3 42 50.3 135.2 284.25 568.5 468.2 center of gravity 2 unpacking and dimensions unpacking to open the banding, pull on the clip as shown in the first drawing. Take the projector out of its shippi...
Page 12
Unpacking and dimensions 2-2 5975338 barcovision 9200 210497 battery installation in the rcu. A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power cord. To install the battery, remove the battery cover on the backside of the remote control by...
Page 13: Installation Guidelines
Installation guidelines 3-1 5975338 barcovision 9200 210497 3 installation guidelines installation guidelines careful consideration of things as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Max. Ambient tempe...
Page 14
Installation guidelines 3-2 5975338 barcovision 9200 210497 * where to install the projector? Definitions of the abbreviation on drawings b = distance between ceiling and top of the screen or between floor and bottom of the screen. A = correction value, distance between bottom side of projec- tor (w...
Page 15
Location and functions of control 4-1 5975338 barcovision 9200 210497 4 location and functions of control front panel terminology rs 232 in remote projector mode : green - operation red - standby communication port (800-peripherals) rs232 out 0 i th is d evice complies wit h part 15 o f t he f cc ru...
Page 16
Location and functions of control 4-2 5975338 barcovision 9200 210497 b. Remote control this remote control includes a battery powered infrared (ir) transmit- ter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up....
Page 17: Installation Set Up
Installation set up 5-1 5975338 barcovision 9200 210497 5 installation set up the projector can be installed to project images in four different configurations : front/table, front/ceiling, rear/table and rear/ceiling. Front/table front/ceiling rear/table rear/ceiling when switching on and the proje...
Page 18
Installation set up 5-2 5975338 barcovision 9200 210497 push the control disk up or down to highlight systems settings and press enter. Enter displays the system settings menu. Exit returns to operational mode. Push the control disk up or down to highlight installation and press enter. System settin...
Page 19: Connections
Connections 6-1 5975338 barcovision 9200 280497 6 connections rs232 out i r- ack no wl edg e d i r- rece i ve d di ag nos ti cs code i r- rece i ve r 100 - 230 v 9 - 4 a 60 - 50 hz 0 i this device complies with part 15 of the fcc rules. Operation is subject to following two conditions : (1) this dev...
Page 20
Connections 6-2 5975338 barcovision 9200 280497 when the total run time of the lamp is 970 hours or more, the following message will be displayed for 1 minute. This message will be repeated every 30 minutes. Press exit to remove the message before the minute is over. When the total run time of the l...
Page 21
Connections 6-3 5975338 barcovision 9200 280497 video/s-video input module to the video input : composite video signals from a vcr, off air signal decoder, etc... 1 x bnc 1.0vpp ± 3 db to the s-video input : separate y-luma/c-chroma signals for higher quality playback of super vhs-signals. Video/s-v...
Page 22
Connections 6-4 5975338 barcovision 9200 280497 rgb analog input module. Rgb analog input terminals with separate horizontal and vertical sync inputs(rgb-hv), with composite sync input(rgb-s) or with sync signals on green(rgsb). Always use an interface when a computer and local monitor have to be co...
Page 23
Connections 6-5 5975338 barcovision 9200 280497 push the control disk key up or down to select system settings and press enter. Use the control disk to select input slots by pushing up or down and press enter. The internal system will scan the inputs and displays the result in the input slots menu. ...
Page 24
Connections 6-6 5975338 barcovision 9200 280497 straps on module level : floating or non-floating input. R-y : j3 : strap "yes" : non floating strap "no" : floating y : j4 : strap "yes" : non floating strap "no" : floating b-y : j5 : strap "yes" : non floating strap "no" : floating s : j6 : strap "y...
Page 25
Connections 6-7 5975338 barcovision 9200 280497 straps on module level : floating or non-floating input. Red : j3 : strap "yes" : non floating strap "no" : floating green : j4 : strap "yes" : non floating strap "no" : floating blue : j5 : strap "yes" : non floating strap "no" : floating h/c : j6 : s...
Page 26
Connections 6-8 5975338 barcovision 9200 280497 loosen the locking open the top cover r b v r b v 100 - 230 v 9 - 4 a 60 - 50 hz rs232 out 0 i this device complies with part 15 of the fcc rules. Operation is subject to following two conditions : (1) this device may not cause harmful interference (2)...
Page 27: Controlling
Controlling 7-1 5975338 barcovision 9200 280497 7 controlling the projector can be controlled with a. The rcu b. The hardwired rcu (cable is not included) c. The local keypad. Controlling the projector with the rcu and the hardwired rcu is equal. How to use the rcu? A) point the front of the rcu to ...
Page 28
Controlling 7-2 5975338 barcovision 9200 280497 switch value 1 1 2 2 3 4 4 8 5 16 6 32 7 64 8 128 example : address 83 dip switch 1 2 3 4 5 6 7 8 setting 1 1 0 0 1 0 1 0 summary : 1x1 + 1x2 + 0x4+ 0x8+ 1x16 + 0x32 + 1x64 + 0x128 = 83 b. How to control the projector or projectors. The projector's add...
Page 29
Controlling 7-3 5975338 barcovision 9200 280497 brightness control a correct 'brightness' setting is important for good image reproduc- tion. Use the + button for a higher brightness. Use the - button for a lower brightness. Contrast control a correct 'contrast' setting is important for good image r...
Page 30
Controlling 7-4 5975338 barcovision 9200 280497 how to get a summary of your projector? The summary gives an overview of : - type of projector - soft version - lamp run time - projector run time - address - installation configuration - baud rate - projector serial number - lamp serial number to disp...
Page 31: Source Set Up
Source set up 8-1 5975338 barcovision 9200 210497 8 source set up input selection use the numeric keys on the rcu or use the local key pad to select the corresponding input slot. The source settings has to be installed for each source when these sources are displayed for the first time. Installation...
Page 32
Source set up 8-2 5975338 barcovision 9200 210497 push the control disk up or down to select the most fitting file and press enter to select. When scrolling through the files, the image will be adapted according the settings of the selected file (on line adaptation). When the best fitting image is d...
Page 33
Source set up 8-3 5975338 barcovision 9200 210497 during the installation of a file with load, the horizontal period, the total number of vertical lines and the interlaced mode are automati- cally measured and filled in in the menu table. These values will be available when starting up the edit proc...
Page 34
Source set up 8-4 5975338 barcovision 9200 210497 vertical refresh [sync/async] : the way of updating the image information on the lcd panels. * for sources with a vertical frequency up to 60 hz : the vertical refresh rate is the same as the vertical frequency of the incoming source. This is a neces...
Page 35
Source set up 8-5 5975338 barcovision 9200 210497 move to move a selected file to the file with the name and extension given in the to area. Use the control disk to select move and press enter. The move menu will be displayed. File service 847f load edit rename copy move delete options move file pal...
Page 36
Source set up 8-6 5975338 barcovision 9200 210497.
Page 37
Picture control in adjustment mode 9-1 5975338 barcovision 9200 210497 9 picture control in adjustment mode the picture control menu is split up in two parts : signal operations and screen operations. Signal operations : to manipulate the video signal, e.G. Sync slow/fast, color balance adjustment e...
Page 38
Picture control in adjustment mode 9-2 5975338 barcovision 9200 210497 gain adjustment per color if the obtained color balance is not yet correct, adjust with the separate gain controls until the desired color balance is obtained. Smoothness the lower the smoothness value, the sharper the image. The...
Page 39
Picture control in adjustment mode 9-3 5975338 barcovision 9200 210497 screen operations select the picture control menu on the main menu by pushing the control disk up or down. Press enter to select. Push the control disk up or down to select screen operations. Press enter to select. When pushing c...
Page 40
Picture control in adjustment mode 9-4 5975338 barcovision 9200 210497 870 870 [window] moves the window upwards 870 870 [window] moves the window downwards 870870 [window] stretches the window in the horizontal direction. 870 870 [window] compresses the window in the horizontal direction. 870 870 [...
Page 41
Picture control in adjustment mode 9-5 5975338 barcovision 9200 210497 870 870 [window] [window] reduces the window, both of horizontal and vertical direc- tions simultaniously. Reset button, brings the window to its maximum dimensions. Picture the picture can be moved, enlarged, reduced within a cr...
Page 42
Picture control in adjustment mode 9-6 5975338 barcovision 9200 210497 [picture] [picture] [picture] [picture] [picture] [picture] compresses the picture in the horizontal direction. Stretches the picture in the vertical direction. Compresses the picture in the vertical direction. Zooms in the pictu...
Page 43
Picture control in adjustment mode 9-7 5975338 barcovision 9200 210497 configure the configure menu contains two toggle functions : geometry and conversion. Use the control disk to select configure and press enter. Screen operations 868b zoom/pan geometry (off) configure conversion [on] geometry [of...
Page 44
Picture control in adjustment mode 9-8 5975338 barcovision 9200 210497 enlarge the upper part of the projected image in horizontal way. Reduce the upper part of the projected image in horizon- tal way. Enlarge the lower part of the projected image in horizontal way. Reduce the lower part of the proj...
Page 45: Service Mode
Service mode 10-1 5975338 barcovision 9200 210497 service mode the service mode offers : - test patterns such as convergence patterns (green, red on green, blue on green and hatch patterns). - alignments for the decoder circuit such as luminance delay, comb filter, etc. (more info in service manual)...
Page 46
Service mode 10-2 5975338 barcovision 9200 210497 factory programmed password : 0000 service mode modify password reset lamp run time lamp run time history convergence display settings decoder settings color balance i2c device test 878 convergence adjustment of the lcd panels. Every lcd panel has 6 ...
Page 47
Service mode 10-3 5975338 barcovision 9200 210497 the pattern shows lines of one pixel. Near six lines on the displayed pattern, a screw is drawn with a number next to it (e.G. If displayed in green = corresponding with the screws and numbers on the green lcd panel). When turning a screw in the dire...
Page 48
Service mode 10-4 5975338 barcovision 9200 210497 two possibilities : 1) distance between red lines is smaller than distance between green lines. Turn screw 5 and 6 clockwise until distance between lines 5 and 6 is the same for the red and green lines. 2) distance between red lines is greater than d...
Page 49
Service mode 10-5 5975338 barcovision 9200 210497 modify password to change your password, highlight 'modify password' and press enter to start up the password modification procedure. Enter your old password with the digit keys. After the fourth digit is entered, the next modify password menu is dis...
Page 50
Service mode 10-6 5975338 barcovision 9200 210497 when reset lamp run time is selected in the service mode menu, the following warning will be displayed : risk of electrical shock. Reset lamp run time is reserved to qualified service personnel. If you are not qualified, press exit to cancel the rese...
Page 51
Standard source set up files a-1 5975388 barcovision 9200 210497 standard source set up files a standard source set up files. Standard preprogrammed set up files. Name resolution fvert fhor fpix ptot pact ltot lact hz khz mhz cga 640 x 200 59,924 15,700 14,318 912 640 262 200 ntsc 675 x 240i 29,970 ...
Page 52
Standard source set up files a-2 5975388 barcovision 9200 210497.
Page 53
Battery replacement in the rcu b - 1 5975338 barcovision 9200 210497 battery replacement in the rcu b fig. 1 battery replacement in the rcu. Remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the rcu. Lift up the top side of the c...
Page 54: Lenses
Lenses c-1 5975338 barcovision 9200 210497 c lenses focusing the lens loosen the fastener ring of the lens by turning counter clockwise. Focus the image by turning the lens barrel to the left or the right. Attention : do not turn out the lens too far, otherwise it will fall out of the lens holder. W...
Page 55
Lenses c-2 5975338 barcovision 9200 210497 lenses this appendix gives an overview of the tables and formulas for the available lenses for the barcovision 9200. The next lenses are available : name length lens diam. Lens weight order number mm (inch) mm (inch) kg (lbs) hd(1.2:1) 253 (9.96) 189 (7.44)...
Page 56: Source Numbers 90 - 99
Source numbers 90 - 99 d - 1 5975338 barcovision 9200 210497 d source numbers 90 - 99 source numbers 90 - 99 these source numbers do not correspond to physical inputs. They can only be used when the projector is equipped with a rcvds 05 or vs05. An additional adjustment file can be created for these...
Page 57: Insert Card
Insert card 5975338 barcovision 9200 210497 p rcu input sources 1 projector rcvds 2 3 4 5 6 1 2 3 5 6 7 8 9 10 input sources 7 p rcu input sources 1 projector rcvds 2 3 4 5 6 1 2 3 5 6 7 8 9 10 input sources 7 " insert card.