Summary of r9002351
Page 1
Owner's manual r9002357 r9002358 vision 708.
Page 2
Barco projection systems date : 200499 owner's manual art. No. : r5976025a r9002357 r9002358 vision 708.
Page 3
Due to constant research, the information in this manual is subject to change without notice. Produced by barco nv, april 1999. All rights reserved. Trademarks are the rights of their respective owners. Barco nv/projection systems noordlaan 5 b-8520 kuurne belgium tel : +32/56/368211 fax : +32/56/35...
Page 4
Table of contents i-1 5976025a barcovision 708 200499 table of contents table of contents ..................................................................................................................................... I-1 safety instructions .......................................................
Page 5
Table of contents i-2 5976025a barcovision 708 200499 picture tuning ............................................................................................................................................. 6-3 color balance ..........................................................................
Page 6
Safety instructions 1-1 5976025a barcovision 708 200499 warning to prevent fire or electrical shock hazard, do not expose this equipment to rain or moisture federal communication commission (fcc statement) this equipment has been tested and found to comply with the limits of a class a digital device...
Page 7
Safety instructions 1-2 5976025a barcovision 708 200499 b. Power cord with ansi 73.11 plug: the wires of the power cord are colored in accordance with the following code. Green/yellow:ground white: neutral black: line (live) 3. Do not allow anything to rest on the power cord. Do not locate this prod...
Page 8
Location and function of controls 2-1 5976025a barcovision 708 200499 2 location and function of controls rear panel terminology rs232in connection between the projector and an ibm pc (or compatible) or mac (rs422) for remote computer control and data communication. Rs232out used to connect to the n...
Page 9
Location and function of controls 2-2 5976025a barcovision 708 200499 control panel terminology a. The local keypad gaining access the local keypad is covered by a door on which the projector logo is screened. To open this door, push as indicated on next drawing and turn it to the front side of the ...
Page 10
Location and function of controls 2-3 5976025a barcovision 708 200499 other functions of the remote control are: - switching between standby and operational modes - switching to "pause" (blanked picture, full power for immediate restarting) - direct access to all connected sources - variable adjustm...
Page 11
Location and function of controls 2-4 5976025a barcovision 708 200499.
Page 12
Connections 3-1 5976025a barcovision 708 200499 3 connections power (mains) cord connection use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. The projector is switched on and off using the ...
Page 13
Connections 3-2 5976025a barcovision 708 200499 source no projector input press digit button 1 comp. Video 1 2 s-video* 2 3 rgbs or rgsb** 3 3 rgb3s or rg3sb*** 4 3 (r-y)y(b-y)s or (r-y)ys(b-y)**** 5 3 (r-y)y(b-y)3s or (r-y)y3s(b-y)***** 6 connecting a composite video source. Composite video signals...
Page 14
Connections 3-3 5976025a barcovision 708 200499 connecting a s-video source to port 2. Separate y-luma/c-chroma signals for higher quality playback of super vhs signals. If a line doubler is built in : the default position of this line doubler is on (active), the video input signal will be displayed...
Page 15
Connections 3-4 5976025a barcovision 708 200499 connecting a rgb analog source with composite sync. Rgb analog input terminals with composite sync input or with sync on green. The projector detects automatically where the sync signal is located. Always use an interface when a computer and local moni...
Page 16
Connections 3-5 5976025a barcovision 708 200499 rgb3s or rg3sb input selection a. Press digit button 4 on the rcu or b. With the local keypad : (to gain access to the local keypad, see 'local keypad' in chapter 'location and function of controls'.) 1. Press adjust key, the general access menu is dis...
Page 17
Connections 3-6 5976025a barcovision 708 200499 (r-y)y(b-y)3s or (r-y)y3s(b-y) input selection a. Press digit button 6 on the rcu or b. With the local keypad : (to gain access to the local keypad, see 'local keypad' in chapter 'location and function of controls'.) 1. Press adjust key, the general ac...
Page 18: Controlling
Controlling 4-1 5976025a barcovision 708 200499 4 controlling caution : do not display a stationary image with full brightness and contrast for longer than 20 min., otherwise you risk damage to the crt's. Battery installation in the rcu. Two batteries are packed together with the rcu. Before using y...
Page 19
Controlling 4-2 5976025a barcovision 708 200499 the projector can be controlled with a. The rcu b. The hardwired rcu (cable not included) c. The local keypad. Controlling the projector with the rcu and the hardwired rcu is the same. How to use the rcu a) point the front of the rcu towards the reflec...
Page 20
Controlling 4-3 5976025a barcovision 708 200499 352-(&725 $''5(66 projector address a. Software set up of the projector address. See 'change projector address' in chapter 'service mode'. Every projector requires an individual address between 0 and 255 which is set in the service mode. Only projector...
Page 21
Controlling 4-4 5976025a barcovision 708 200499 $'-867 67$1'% (17(5 (;,7 general access select with , or then . To return sharpness tint color brightness contrast 5 6 3 4 1 2 enter adjust general access select with , or then . To return sharpness tint color brightness contrast 5 6 3 4 1 2 enter adju...
Page 22
Controlling 4-5 5976025a barcovision 708 200499 brightness control a correct 'brightness' setting is important for good image reproduction. Adjust the brightness with the + button and - button (rcu) or pushing the control disc to the left or to the right (local keypad) until the darkest parts of the...
Page 23
Controlling 4-6 5976025a barcovision 708 200499.
Page 24
Start up adjustment mode 5-1 5976025a barcovision 708 200499 5 start up of the adjustment mode adjustment mode all picture geometry and convergence adjustments are made while in the 'adjustment mode'. Two possible ways to enter the adjustment mode : a) using the rcu. Press the adjust key. The projec...
Page 25
Start up adjustment mode 5-2 5976025a barcovision 708 200499 while in guided or random access adjustment mode, the user may use an external source, an internally generated genlocked pattern or an internally generated multifrequency cross hatch pattern as a setup pattern. Warning during the start up ...
Page 26
Random access adjustment mode 6-1 5976025a barcovision 708 200499 6 random access adjustment mode starting up the random access adjustment mode. Push the cursor keys up or down to highlight "random access" and then press enter. Some items in the random access mode are password protected (when the pa...
Page 27
Random access adjustment mode 6-2 5976025a barcovision 708 200499 selecting setup pattern if an external source is connected to the projector, this menu will be displayed. Push the cursor keys up or down to highlight the desired setup pattern and then press enter. Genlocked pattern : internally gene...
Page 28
Random access adjustment mode 6-3 5976025a barcovision 708 200499 select with or then to return. Random access adjustment mode picture tuning geometry convergence color select select with or to accept to return. Picture tuning color balance sync : fast decoding : ebu port2 : video chroma delay : on ...
Page 29
Random access adjustment mode 6-4 5976025a barcovision 708 200499 decoding only for ntsc signals. The possibility is offered to decode the ntsc video signals via the normal american ire standard or via the european ebu standard. To change the decoding setting, handle as follow : 1. Push the cursor k...
Page 30
Random access adjustment mode 6-5 5976025a barcovision 708 200499 select with or then to return. Random access adjustment mode picture tuning geometry convergence color select geometry adjustments the geometry adjustments have to be done only on the green image. These adjustments are automatically i...
Page 31
Random access adjustment mode 6-6 5976025a barcovision 708 200499 to start the adjustment : 1. Push the cursor key é or ê to highlight raster shift. 2. Press enter. The green raster will be displayed. Select with or then to return. Geometry h phase raster shift left-right (e-w) top-bottom (n-s) size...
Page 32
Random access adjustment mode 6-7 5976025a barcovision 708 200499 select with or then to return. Left-right (e-w) v centerline bow v centerline skew right bow right keystone left bow left keystone seagull correction left-right (east-west) adjustments left-right and center adjustments affect only the...
Page 33
Random access adjustment mode 6-8 5976025a barcovision 708 200499 select with or then to return. Top-bottom (north-south) adjustments top-bottom and center adjustments affect only the horizontal lines of the projected image. To start up the top-bottom and center corrections, follow the next procedur...
Page 34
Random access adjustment mode 6-9 5976025a barcovision 708 200499 top-bottom select with or then to return. H centerline bow h centerline skew top bow top keystone bottom bow bottom keystone correct by pushing the cursor key down correct by pushing the cursor key up corrects for curvature of the hor...
Page 35
Random access adjustment mode 6-10 5976025a barcovision 708 200499 vertical linearity adjustment the vertical linearity adjustment function corrects for vertical non- linearities which extend from the center of the image to the top and bottom of the image. 1. Push the cursor key é or ê to highlight ...
Page 36
Random access adjustment mode 6-11 5976025a barcovision 708 200499 blanking adjustments blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A 0% on the bar scale indicat...
Page 37
Random access adjustment mode 6-12 5976025a barcovision 708 200499 convergence adjustment convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image whil...
Page 38
Service mode 7-1 5976025a barcovision 708 200499 7 service mode starting up the service mode. 1. Push the cursor key é or ê to select to service 2. Press enter. Some items in the service mode are password protected (when the password function is active). Enter your password to continue. All other pa...
Page 39
Service mode 7-2 5976025a barcovision 708 200499 projector set-up to select projector set-up : 1. Push the cursor key é or ê to highlight projector set_up. 2. Press enter within the projector set-up menu, the following items can be consultated or set to the desired setting : - identification - total...
Page 40
Service mode 7-3 5976025a barcovision 708 200499 change password this item is password protected. To select change password : 1. Push the cursor key é or ê to highlight change password. 2. Press enter if it is the first time you enter a password protected item, enter your password and press enter. T...
Page 41
Service mode 7-4 5976025a barcovision 708 200499 change baudrate the communication speed between projector and computer has 8 possible speeds. The baud rate speed can be software set up. To set up the baudrate : 1. Push the cursor key é or ê to highlight change baudrate. 2. Press enter. The followin...
Page 42
Service mode 7-5 5976025a barcovision 708 200499 select with or then to return. Service mode projector set-up memory management common settings i2c diagnostics select with or then to return. Memory management copy a block delete a block delete all blocks all settings to midpos r & b convergence mid ...
Page 43
Service mode 7-6 5976025a barcovision 708 200499 select with or then to return. Memory management copy a block delete a block delete all blocks all settings to midpos r & b convergence mid gr convergence mid deletion of all blocks to delete all blocks : 1. Push the cursor key é or ê to highlight del...
Page 44
Service mode 7-7 5976025a barcovision 708 200499 r & b convergence mid item is password protected. To set the convergence settings for red and blue in midposition : 1. Push the cursor key é or ê to highlight r & b convergence mid. 2. Press enter. A confirmation screen will be displayed first. 3. Pre...
Page 45
Service mode 7-8 5976025a barcovision 708 200499 crt run in cycle a flashing white pattern will be generated until is pressed. The projector only uses memory blocks adjusted on an internal # pattern; if no such block is available, the projector can't run the procedure and leaves the adjusment mode. ...
Page 46
Service mode 7-9 5976025a barcovision 708 200499 projector warm up to select projector warm up : 1. Push the cursor key é or ê to highlight projector warm up. 2. Press enter the projector warm up menu will be displayed. The projector needs this warm up periode to reach its maximum specifications and...
Page 47
Service mode 7-10 5976025a barcovision 708 200499 how to recall a specific memorybank for the actual source ? When the memory bank option is on and a source is selected, this source will be displayed with the last used memory bank settings. An on-screen menu will give a indication of the memory bank...
Page 48
Messages, warnings and failures 8-1 5976025a barcovision 708 200499 8 messages, warnings and failures when selecting a new source, information about this source will be displayed on the screen. Source number, horizontal and vertical fre- quencies of the displayed source. Source 01 announcement of th...
Page 49
Messages, warnings and failures 8-2 5976025a barcovision 708 200499 failure rcvds com- munication error serial communication error be- tween the rcvds and the projec- tor. Fan failed projector will switch off message when one of the fans are not working anymore. Projector switches to stand-by.
Page 50
Adjustment blocks and source numbers 90-99 a-1 5976025a barcovision 708 200499 adjustment blocks (memory blocks) as the projector is digitally controlled, all geometry and convergence adjustments are stored in the projectors memory as numeric values. These numeric values are used to control digital...