1. DL manuals
  2. Barco
  3. Projector
  4. R9002400
  5. Installation Manual

Barco R9002400 Installation Manual

Other manuals for R9002400: Owner's Manual

Summary of R9002400

  • Page 1

    Installation manual cine 9 r9002400

  • Page 3: Barco Projection Systems

    Barco projection systems date : 26032002 installation manual rev. : 02 cine 9 r9002400 art. No. : r5976195.

  • Page 4

    Due to constant research, the information in this manual is subject to change without notice. Produced by barco nv, march 2002. All rights reserved. Trademarks are the rights of their respective owners. Barco n.V./projection systems noordlaan 5 b-8520 kuurne belgium tel : +32/56/368211 fax : +32/56/...

  • Page 5: Table of Contents

    Table of contents i -1 5976195 barcocine 9 31012002 i table of contents safety instructions..................................................................................................... 1-1 safety instructions ......................................................................................

  • Page 6

    Table of contents i -2 5976195 barcocine 9 31012002 source connections ................................................................................................... 6-1 input sources ..................................................................................................................

  • Page 7: Safety Instructions

    Safety instructions 1-1 5976195 barcocine 9 31012002 1 safety instructions safety instructions notice on safety this equipment is built in accordance with the requirements of the international safety standards en60950, ul 1950 and csa c22.2 no.950, which are the safety standards of information techn...

  • Page 8

    Safety instructions 1-2 5976195 barcocine 9 31012002 safety warning to prevent fire or electrical shock hazard, do not expose this equipment to rain or moisture federal communication commission (fcc statement) this equipment has been tested and found to comply with the limits of a class a digital de...

  • Page 9

    Safety instructions 1-3 5976195 barcocine 9 31012002 caution on fire hazard do not place flammable or combustible materials near projector ! Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat on its externa...

  • Page 10

    Safety instructions 1-4 5976195 barcocine 9 31012002 on repacking save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory. On illumination in order to o...

  • Page 11: Packing And Dimensions

    Packing and dimensions 2-1 5976195 barcocine 9 31012002 2 packing and dimensions unpacking unpacking to open the banding around the carton, pull out the clip as shown below : take the projector out of its shipping carton. Be aware of the weight of the projector : 85 kg (188 lbs). To carry the projec...

  • Page 12

    Packing and dimensions 2-2 5976195 barcocine 9 31012002 projector dimensions (in mm).

  • Page 13: Installation Guidelines

    Installation guidelines 3-1 5976195 barcocine 9 31012002 3 installation guidelines installation guidelines ambient temperature conditions careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the proj...

  • Page 14

    Installation guidelines 3-2 5976195 barcocine 9 31012002 which screen type? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. Screens are rated by how much light they reflect (or transmit in the ...

  • Page 15

    Installation guidelines 3-3 5976195 barcocine 9 31012002 projector configuration which configuration can be used. The projector can be installed to project images in four different configurations (image 1): rear/ceiling, rear/table, front/ceiling or front/table. Image 1 positioning the projector the...

  • Page 16

    Installation guidelines 3-4 5976195 barcocine 9 31012002 image 1 battery installation in the rcu. How are the batteries delivered ? Two batteries are packed together with the power cord. Before using your rcu, install first these batteries. How to install ? 1 remove the battery cover on the backside...

  • Page 17: Installation Setup

    Installation setup 4-1 5976195 barcocine 9 31012002 4 installation setup access to controls warning risk of electric shock ! The installation should only be done by barco authorized service personnel opening the top cover during the projector setup and installation it is necessary to open the top co...

  • Page 18

    Installation setup 4-2 5976195 barcocine 9 31012002 reinstalling the top cover to reinstall the top cover on the projector : 1 place the top cover back on the projector. 2 bring the two parts of the hinges right in front of each other (image 2). 3 insert the handles back in the hinges. 4 secure the ...

  • Page 19

    Installation setup 4-3 5976195 barcocine 9 31012002 horizontal scan switches access to the connectors 1 open the top cover and remove it from the projector (see 'removing top cover' ); 2 loosen the 3 retaining screws on each side of the projector (image 1); 3 open the protection plate and pivot it f...

  • Page 20

    Installation setup 4-4 5976195 barcocine 9 31012002 j151: horizontal red scan connector j251: horizontal green scan connector j351: horizontal bleu scan connector j152: vertical red scan connector j252: vertical green scan connector j352: vertical bleu scan connector horizontal scan connectors when ...

  • Page 21

    Installation setup 4-5 5976195 barcocine 9 31012002 all projectors leave the factory set with a ceiling/front configuration. Scan position check to check the scan position i.E. The orientation of the scan connectors proceed as follows: this procedure can only be done after power (mains) connection. ...

  • Page 22

    Installation setup 4-6 5976195 barcocine 9 31012002.

  • Page 23: Ac Power Connections

    Ac power connections 5-1 5976195 barcocine 9 31012002 5 ac power connections ac power cord ac power cord connection use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the rear side of the projector. Preparing the power...

  • Page 24

    Ac power connections 5-2 5976195 barcocine 9 31012002 ac power the power voltage the power input voltage is autoranging between 100v (-10%) and 240v (+6%) fuses power cord with an ansi 73.11 plug the wires of the delivered mains lead (power cord) are colored in accordance with the following code : y...

  • Page 25

    Ac power connections 5-3 5976195 barcocine 9 31012002 switching on the projector switching on the projector is switched on and off using the power (mains)switch. Pressed : on not pressed : off power switch stand by indication lamp : no light up : projector switched off green color : projector in ope...

  • Page 26

    Ac power connections 5-4 5976195 barcocine 9 31012002 start up in stand by mode the projector starts up in stand by. Press a digit key corresponding to the desired source or press stby key. The projector displays the selected source or the warm up cycle message. When this warm up message appears on ...

  • Page 27: Source Connections

    Source connections 6-1 5976195 barcocine 9 31012002 6 source connections input sources input facilities the following source types can be connected to the inputs : 1 composite video 2 s-video 3 rgbs or rgsb 4 rgb3s or rg3sb 5 (r-y)y(b-y)s or (r-y)ys(b-y) [component input] 6 (r-y)y(b-y)3s or (r-y)y3s...

  • Page 28

    Source connections 6-2 5976195 barcocine 9 31012002 connecting a composite video source to port 1 composite video signals coming from a vcr, off air signal decoder and so on can be connected to port 1. 75 w termination switch for video terminate the video input of the projector using the 75 w switch...

  • Page 29

    Source connections 6-3 5976195 barcocine 9 31012002 pin assignment for the 4 pin connector how to select s-video (or composite video) source: select the s-video input by pressing the numeric button 2 on the rcu or the local keypad. 3,1 3,1 3,1 3,1 ($57+*5281'/80,1$1&( ($57+*5281'&+520,1$1&( /80,1$1&...

  • Page 30

    Source connections 6-4 5976195 barcocine 9 31012002 connecting a rgb analog source to port 3 connect a rgb analog signal via an interface (e.G. Rgb 120mhz interface, part number 98 26570) to port 3: rgb analog input with automatic sync detection (separate h and v sync inputs, with composite sync inp...

  • Page 31

    Source connections 6-5 5976195 barcocine 9 31012002 75 w termination resistors in case of chaining (loop-through) the projectors, the 75 w line termination resistors must be removed from the second rgb input module when the projector is not the last unit in the chain. In case of a stand-alone projec...

  • Page 32

    Source connections 6-6 5976195 barcocine 9 31012002 connecting a rgb analog source to port 4/5 rgb analog input terminals with separate h and v sync inputs, composite sync input or sync signals on green can be connected to the projector via port 4/5. The projector automatically detects where the syn...

  • Page 33

    Source connections 6-7 5976195 barcocine 9 31012002 connecting a rgb analog source with tri-level sync to port 4/5 rgb analog input terminals with tri-level sync input or with tri-level sync on green can be connected to the projector via port 4/5. The projector detects automatically where the sync s...

  • Page 34

    Source connections 6-8 5976195 barcocine 9 31012002 communication connections communication facilities : 1. Rs232 in / rs232 out. 2. Comm port for communication with peripheral (switchable between ppm and rc5) 3. Rc for remote cable connection with the rcu. 4. Mouse to control a pc with the projecto...

  • Page 35

    Installation adjustment mode 7-1 5976195 barcocine 9 31012002 7 installation adjustment mode installation adjustment mode access to the service menus 1 press the adjust key. The projector displays the 'main menu' (menu 1) 2 push the cursor key é or ê to highlight the path 'service menus' in menu1. 3...

  • Page 36

    Installation adjustment mode 7-2 5976195 barcocine 9 31012002 overview flowchart of the installation adjustment mode access to adjustments the top cover of the projector should be removed in order to gain access to the adjustments. Please refer to 'removing the top cover' for how to remove the top c...

  • Page 37

    Installation adjustment mode 7-3 5976195 barcocine 9 31012002 2 on the screen, a drawing (projection distance 1 menu) will be displayed together with parameters indicating a correct position. To change the screen width (see flowchart above) : 1 push the cursor key ç or è to highlight the item sw in ...

  • Page 38

    Installation adjustment mode 7-4 5976195 barcocine 9 31012002 optical lens focusing the optical focusing procedure is performed separately for each lens. The appropriate crt will be switched on as the user proceeds through the optical focusing adjustment sequence. Following screen will be projected ...

  • Page 39

    Installation adjustment mode 7-5 5976195 barcocine 9 31012002 raster centering raster centering contrast level is reduced and brightness increased to make the raster visible on the face plate of each crt. Use the arrow keys to center the raster on the green, red and blue crt respectively. To continu...

  • Page 40

    Installation adjustment mode 7-6 5976195 barcocine 9 31012002 a new projection angle adjustment is required whenever a new screenwidth sw is adopted. Case 1: blue crosshair on the left of the green crosshair action on crt: move the blue crt away (to the outside) from the green crt case 2: blue cross...

  • Page 41

    Installation adjustment mode 7-7 5976195 barcocine 9 31012002 scheimpflug adjustment (diagonal image focusing) why? With the diagonal image focusing corrections, it is possible to obtain uniform focus for the total projected image. These corrections must be repeated for each color. The diagonal imag...

  • Page 42

    Installation adjustment mode 7-8 5976195 barcocine 9 31012002.

  • Page 43

    Messages, warnings and failures 8-1 5976195 barcocine 9 31012002 8 messages, warnings and failures when selecting a new source, information about this source will be displayed on the screen. Source number, horizontal and vertical fre- quencies of the displayed source. Source 01 rgb2 announcement of ...

  • Page 44

    Messages, warnings and failures 8-2 5976195 barcocine 9 31012002 failure rcvds com- munication error serial communication error be- tween the rcvds and the projector. Failure invalid input input not valid failure pc communica- tion error error in the communication between the projector and the pc. F...

  • Page 45: Barco Ceiling Mount Support

    Barco ceiling mount support a-1 5976195 barcocine 9 31012002 exploded view of barco ceiling mount support (image 1) overview drawing of the total system (image 2) introduction this appendix gives only an overview of the contents of the installation guidelines and some overview drawings. The installa...

  • Page 46

    Barco ceiling mount support a-2 5976195 barcocine 9 31012002.

  • Page 47: Gamma Corrections

    Gamma corrections b-1 5976195 barcocine 9 31012002 b gamma corrections gamma corrections gamma warning when entering the gamma corrections, a warning will be displayed (menu 1) : "risk of incorrect adjustment of the projector. The gamma corrections are factory adjusted using an actas color analyzer ...

  • Page 48

    Gamma corrections b-2 5976195 barcocine 9 31012002 to carry out the red and blue midlights correction: 1 push the cursor key é or ê to highlight the item r&b midlights in the menu and then press the enter key (menu 1). If the exit key is pressed, the projector will return to the service menu. 2 push...

  • Page 49

    Formula outside package dimensions (inches) chemical family federal stock number (fsn) gross weight (lbs) % treshold limit value (units) alloys and metallic coatings % % pigments solvents additives catalyst vehicle hazardous mixtures of other liquids, solids, or gases appearance and odor boiling poi...

  • Page 50

    Stability unstable stable conditions to avoid incompatability (materials to avoid) hazardous decomposition products hazardous polymerization will not occur conditions to avoid may occur steps to be taken in case material is released or spilled waste disposal method respiratory protection (specific t...