1. DL manuals
  2. Barco
  3. Projector Accessories
  4. R9827880
  5. Owner's Manual

Barco R9827880 Owner's Manual

Manual is about: projection system

Summary of R9827880

  • Page 1

    R5975765 rcvds05 020997 1 r5975765 rcvds05 020997 1 barco projection systems date: 30.06.98 art. No. R5975765 owner's manual r9827880 r9827881 r9827888 r9827889 rcvds 05 revision : 06 barco projection systems date: 30.06.98 art. No. R5975765 owner's manual r9827880 r9827881 r9827888 r9827889 rcvds 0...

  • Page 2

    R5975765 rcvds05 020997 2 r5975765 rcvds05 020997 2 due to constant research, the information in this manual is subject to change without notice. Produced by barco nv, june 1998. All rights reserved. Trademarks are the rights of their respective owners. Barco nv/projection systems noordlaan 5 b-8520...

  • Page 3

    R5975765 rcvds05 020997 3 r5975765 rcvds05 020997 3 i. Safety instructions ............................................................................................. 7 i.1 notice on safety .................................................................................... 7 i.2. Installation ins...

  • Page 4

    R5975765 rcvds05 020997 4 r5975765 rcvds05 020997 4 c.2.2. Signal connection between multiple rcvds05's. ........................ 34 c.3. Optional remote ir receiver to rcvds05. ..................................... 35 d. Rcvds05 used as high bandwidth signal splitter. .................................

  • Page 5

    R5975765 rcvds05 020997 5 r5975765 rcvds05 020997 5 vii. Error codes ................................................................................................... 66 viii. Optional decoder ......................................................................................... 68 table of con...

  • Page 6

    R5975765 rcvds05 020997 6 r5975765 rcvds05 020997 6 table of contents table of contents table of contents table of contents.

  • Page 7

    R5975765 rcvds05 020997 7 r5975765 rcvds05 020997 7 safety instructions safety instructions safety instructions safety instructions i. Safety instructions i.1 notice on safety rcvds05s are built in accordance with the requirements of the international safety standards iec 950 and ul 1950, which are ...

  • Page 8

    R5975765 rcvds05 020997 8 r5975765 rcvds05 020997 8 safety instructions safety instructions safety instructions safety instructions the lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons. The...

  • Page 9

    R5975765 rcvds05 020997 9 r5975765 rcvds05 020997 9 safety instructions safety instructions * all the safety and operating instructions should be read before using this unit. * the safety and operating instructions manual should be retained for future reference. * all warnings on the projector and i...

  • Page 10

    R5975765 rcvds05 020997 10 r5975765 rcvds05 020997 10 safety instructions safety instructions safety instructions safety instructions b. Power cord with ansi 73.11 plug: the wires of the power cord are colored in accordance with the following code. Green/yellow: ground white: neutral black: line (li...

  • Page 11

    R5975765 rcvds05 020997 11 r5975765 rcvds05 020997 11 safety instructions safety instructions safety instructions safety instructions this product should never be placed near or over a radiator or heat register. This switcher should not be placed in a built-in installation or enclosure unless proper...

  • Page 12

    R5975765 rcvds05 020997 12 r5975765 rcvds05 020997 12 safety instructions safety instructions safety instructions safety instructions solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. I.7. On repacking save the original shippi...

  • Page 13

    R5975765 rcvds05 020997 13 r5975765 rcvds05 020997 13 introduction introduction introduction introduction ii. Introduction the rcvds05 offers the possibility to connect a wide range of video, data and graphics sources to one or more projectors or other displays. Its modular input design makes it pos...

  • Page 14

    R5975765 rcvds05 020997 14 r5975765 rcvds05 020997 14 introduction introduction introduction 2. As splitter. Rcvds05 rgb analog rgb analog composite video communication link composite video rgb analog comp. Video rgb analog comp. Video rgb analog 3. As stand alone system switcher. Rgb analog rgb ana...

  • Page 15

    R5975765 rcvds05 020997 15 r5975765 rcvds05 020997 15 input modules input modules input modules iii. Input modules as the rcvds05 works as an interface between the different input sources and the display (projector or monitor) it connects the following sources through to the output module or modules...

  • Page 16

    R5975765 rcvds05 020997 16 r5975765 rcvds05 020997 16 input modules input modules input modules input modules $ % a. Input module installation. Up to 10 input modules can be inserted in any order in the rcvds05. Install the input modules in the rcvds05 as follows : 1. Power down the rcvds05 and disc...

  • Page 17

    R5975765 rcvds05 020997 17 r5975765 rcvds05 020997 17 input modules input modules input modules input modules b. Source connection to the rcvds05. B.1. Input module : video/s-video. Order number : 98 27900 signal connection : video composite, s-video and audio. Composite video : 1xbnc 1.0vpp ± 3 db ...

  • Page 18

    R5975765 rcvds05 020997 18 r5975765 rcvds05 020997 18 input modules input modules input modules input modules straps on module level : floating or non-floating input. Video input : j11 : strap "yes" : non floating strap "no" : floating s-video input : j12 : strap "yes" : non floating strap "no" : fl...

  • Page 19

    R5975765 rcvds05 020997 19 r5975765 rcvds05 020997 19 input modules input modules b.2. Input module : rgbs/rgsb analog. Order number : 98 27910 rgbs/rgsb analog : 5 x bnc red : 0.7 vpp ± 3 db blue : 0.7 vpp ± 3 db green : 0.7 vpp ± 3 db 1 vpp ± 3 db if sync on green vert. Sync : 1 vpp to 4 vpp ± 3 d...

  • Page 20

    R5975765 rcvds05 020997 20 r5975765 rcvds05 020997 20 ) or d wlq j r u q r q ior d wlq j lq s x w floating non-floating - 6 6 h s d ud wh v \ q f 6 \ q f r q j uh h q - - - - - input modules input modules ) or d wlq j r u q r q ior d wlq j lq s x w floating non-floating - 6 6 h s d ud wh v \ q f 6 \...

  • Page 21

    R5975765 rcvds05 020997 21 r5975765 rcvds05 020997 21 input modules input modules rgb3s/rg3sb analog : 5 x bnc red : 0.7 vpp ± 3 db blue : 0.7 vpp ± 3 db green : 0.7 vpp ± 3 db 1 vpp ± 3 db if tri-level sync on green vert. Tri-level sync : 1 vpp to 4 vpp ± 3 db hor. Tri-level sync / composite tri-le...

  • Page 22

    R5975765 rcvds05 020997 22 r5975765 rcvds05 020997 22 input modules input modules input modules floating or non-floating input. R-y : j3 : strap "yes" : non floating strap "no" : floating y : j4 : strap "yes" : non floating strap "no" : floating b-y : j5 : strap "yes" : non floating strap "no" : flo...

  • Page 23

    R5975765 rcvds05 020997 23 r5975765 rcvds05 020997 23 )ordwlqjruqrqiordwlqjlqsxw floating non-floating 6\qfvhohfwlrq 6 h s d ud wh v \ q f 6 \ q f r q - - - - - - 1 r u p d o6 \ q f 7ulohyho6\qf - - input modules input modules )ordwlqjruqrqiordwlqjlqsxw floating non-floating 6\qfvhohfwlrq 6 h s d ud...

  • Page 24

    R5975765 rcvds05 020997 24 r5975765 rcvds05 020997 24 b.5. Input module : rgbs/rgsb analog for line doubling* order number : r9828410 rgbs/rgsb analog : 4 x bnc red : 0.7 vpp ± 3 db blue : 0.7 vpp ± 3 db green : 0.7 vpp ± 3 db 1 vpp ± 3 db if sync on green comp. Sync : 0.3 vpp to 4 vpp ± 3 db polari...

  • Page 25

    R5975765 rcvds05 020997 25 r5975765 rcvds05 020997 25 special modules special modules iv. Special modules a. Expansion module order number : 98 28000 to allow more inputs than a rcvds05 can normally accept, several rcvds05's can be connected in series to allow swicthing of up to 90 sources. Signal c...

  • Page 26

    R5975765 rcvds05 020997 26 r5975765 rcvds05 020997 26 special modules b. Communication interface module order number : 98 28010 when the rcvds05's are linked or the optional ir remote receiver will be used or your rcvds05 will be controlled by a central computer, a communication module must be insta...

  • Page 27

    R5975765 rcvds05 020997 27 r5975765 rcvds05 020997 27 special modules special modules switch function rs232 - barco a) rcvds05 used with barco projector : switch in position "barco". B) rcvds05 used as stand alone unit : switch in position "barco". C) rcvds05 controlled by a central computer : switc...

  • Page 28

    R5975765 rcvds05 020997 28 r5975765 rcvds05 020997 28 special modules special modules c. 5 cable output module. Order number : 98 27950 all signals, video, s-video, rgb analog as well as component video are transferred via 5 output bnc's. This module is designed to be used as an output module in lin...

  • Page 29

    R5975765 rcvds05 020997 29 r5975765 rcvds05 020997 29 installation installation v. Installation a. Power (mains) connection a.1. Power requirements the power input is auto-ranging from 100 to 240 vac 100 - 240 v 0.8 - 0.4 a 60 - 50 hz 50 watt a.2. Power cord (mains lead) information. If it becomes n...

  • Page 30

    R5975765 rcvds05 020997 30 r5975765 rcvds05 020997 30 installation installation a.3. Power cord connection plug the male end of the power cord into an available power outlet. A.4. Switching on the rcvds05 is switched on and off using the power (mains) switch on/off on the front of the rcvds05. Press...

  • Page 31

    R5975765 rcvds05 020997 31 r5975765 rcvds05 020997 31 installation installation b. Rcvds05 used as source selector for a barco projector. B.1. Rcvds05 to projector communication link. Plug the male d9 connector of a communication cable into the female d9 connector labelled "to projector" on the back...

  • Page 32

    R5975765 rcvds05 020997 32 r5975765 rcvds05 020997 32 installation installation b.2.2. Rcvds05 to audio amplifier. Connect the left and right audio outputs (connectors below the output module) of the rcvds05 to the left and right audio inputs of an audio amplifier using two conductor audio cables wi...

  • Page 33

    R5975765 rcvds05 020997 33 r5975765 rcvds05 020997 33 installation installation r l r l r to projector 98 28020 98 27920 r l r l r to projector 98 28020 98 27930 98 27920 98 28010 98 28000 rcvds - 1 rcvds - 2 mode switch in "barco" mode ' pdoh ' i b.4. Optional remote ir receiver to rcvds05. The rcv...

  • Page 34

    R5975765 rcvds05 020997 34 r5975765 rcvds05 020997 34 installation installation by the remote ir receiver. Plug the male d9 connector of the communication cable into the female d9 connector on the rear of the ir remote receiver. Plug the female d9 connector of the communication cable into the male d...

  • Page 35

    R5975765 rcvds05 020997 35 r5975765 rcvds05 020997 35 installation installation c.1. Signal connection. C.1.1. Rcvds05 to display. Connect the video output of the rcvds05 to the video input of the display using a coaxial cable with bnc connectors. Connect the s-video output of the rcvds05 to the s-v...

  • Page 36

    R5975765 rcvds05 020997 36 r5975765 rcvds05 020997 36 installation installation c.1.2. Rcvds05 to audio amplifier. Connect the left and right audio outputs (connectors below the output module) of the rcvds05 to the left and right audio inputs of an audio amplifier using two conductor audio cables wi...

  • Page 37

    R5975765 rcvds05 020997 37 r5975765 rcvds05 020997 37 installation installation c.3. Optional remote ir receiver to rcvds05. The rcvds05 must be equipped with a communication interface module to connect the optional remote ir receiver to the rcvds05. The switch on the communication interface module ...

  • Page 38

    R5975765 rcvds05 020997 38 r5975765 rcvds05 020997 38 plug the male d9 connector of the communication cable into the female d9 connector on the rear of the ir remote receiver. Plug the female d9 connector of the communication cable into the male d9 connector labelled "to next device" on the face of ...

  • Page 39

    R5975765 rcvds05 020997 39 r5975765 rcvds05 020997 39 installation installation d. Rcvds05 used as high bandwidth signal splitter. D.1. Use of multiple output modules. The rcvds05 can be equipped with maximum 4 output modules. The selected input signal will be splitted to each output module. D.2. Si...

  • Page 40

    R5975765 rcvds05 020997 40 r5975765 rcvds05 020997 40 installation installation rcvds05 to the red, green, blue, h/s sync and v sync inputs of the display 1 using coaxial cable with bnc connectors. Repeat these connections respectively for output module 2 to display 2, output module 3 to display 3 a...

  • Page 41

    R5975765 rcvds05 020997 41 r5975765 rcvds05 020997 41 installation installation installation installation 5 / 5 / 5 72352-(&725 6 7 $ 1 ' $ 5 ' 2 8 7 3 8 7 vi d e o s- v id e o r g b h / c v 98 28020 r- y y b- y s on 98 27930 & 2 0 3 2 1 ( 1 7 9 ,' ( 2 ,1 3 8 7 r g b h / c v on 5 * % / ( 9 ( / 6 1 &...

  • Page 42

    R5975765 rcvds05 020997 42 r5975765 rcvds05 020997 42 installation installation plug the female d9 connector of a serial cable into the male connector of the serial port of your computer. All rs232 commands have to be sent to the projector. Only the comandfor the projector can be used. These command...

  • Page 43

    R5975765 rcvds05 020997 43 r5975765 rcvds05 020997 43 installation installation e.2.2. Address setting on the rcvds05. To communicate with the computer, a unique address must be set on the communi- cation module. That unique address must be an address between 0 and 15. To set up the address, see cha...

  • Page 44

    R5975765 rcvds05 020997 44 r5975765 rcvds05 020997 44 installation installation a 4-wire coaxial cable with 4 pin plugs. Connect the red, green, blue, h/s sync and v sync outputs of the rcvds05 to the red, green, blue, h/s sync and v sync inputs of the display using coaxial cable with bnc connectors...

  • Page 45

    R5975765 rcvds05 020997 45 r5975765 rcvds05 020997 45 installation the second rcvds05 and the audio connectors below the expansion module of the first rcvds05. Installation 5 / 5 / 5 7235 2-( & 725 67 $ 1 ' $ 5 ' 2 8 73 8 7 vi deo s- vi de o rg b h / c v 98 28020 rg b h / c v on 5 * % / ( 9( /6 & ,1...

  • Page 46

    R5975765 rcvds05 020997 46 r5975765 rcvds05 020997 46 installation installation e.4.3. Signal connection between multiple rcvds's multiple displays. No expansion module must be installed in the rcvds's. The switch on each communication module must be set in the position 'rs232'. Example : 2 rcvds's ...

  • Page 47

    R5975765 rcvds05 020997 47 r5975765 rcvds05 020997 47 installation installation the output signals on the output module of the first rcvds05 are connected to the inputs of the first display. The output signals on the output module of the second rcvds05 are connected to the inputs of the second displ...

  • Page 48

    R5975765 rcvds05 020997 48 r5975765 rcvds05 020997 48 operating instructions operating instructions vi. Operating instructions a. On/off switching the rcvds05 is switched on and off using the power (mains) switch on/off on the front of the rcvds05. Pressed : on not pressed : off b. "beep" indication...

  • Page 49

    R5975765 rcvds05 020997 49 r5975765 rcvds05 020997 49 operating instructions operating instructions c.1. One rcvds05. The rcvds05 counts its own inputs (free and occupied slots) starting with slot 1 (left most slot when viewing the backside). Each empty slot before the last occupied slot will be cou...

  • Page 50

    R5975765 rcvds05 020997 50 r5975765 rcvds05 020997 50 operating instructions operating instructions second example : rcvds05 equiped with the same modules as in example one, but the module in slot 4 is removed. L r l r l r l r l r l r l r l r l r l r l r to projector 9 8 2 80 20 9 8 27 91 0 9 8 27 9...

  • Page 51

    R5975765 rcvds05 020997 51 r5975765 rcvds05 020997 51 operating instructions operating instructions example one : double rcvds05 with the following input slots. Rcvds - 1 slot 1 : rgb analog input module slot 2 : video/s-video input module slot 3 : rgb analog input module slot 4 : expansion module r...

  • Page 52

    R5975765 rcvds05 020997 52 r5975765 rcvds05 020997 52 operating instructions operating instructions rcvds - 2 slot 1 : rgb analog input module slot 2 : rgb analog input module l r l r l r l r l r l r l r l r l r l r l r to proje ctor 98 280 20 9 8 2 791 0 98 2 7900 9 8 2791 0 98 2 801 0 l r l r l r ...

  • Page 53

    R5975765 rcvds05 020997 53 r5975765 rcvds05 020997 53 operating instructions operating instructions d. Operating the rcvds05 with the button panel or rcu. The controls on the button panel of the rcvds05 are : - source selection - analog image setting - stand by switching - text on/off - pause functi...

  • Page 54

    R5975765 rcvds05 020997 54 r5975765 rcvds05 020997 54 operating instructions operating instructions if there are more than 10 sources connected to the rcvds05 (max. 20 sources possible): when selecting a source between 2 and 9, key in the corresponding number with the numeric keys. When selecting a ...

  • Page 55

    R5975765 rcvds05 020997 55 r5975765 rcvds05 020997 55 operating instructions operating instructions continue with 7. Or enter 7 and wait two seconds, source 7 will selected. Example 2 : source 17 enter 1, the display shows : enter 7 within two seconds, the corresponding source will be selected. Only...

  • Page 56

    R5975765 rcvds05 020997 56 r5975765 rcvds05 020997 56 67% 212)) 67% 212)) operating instructions operating instructions d.3. Stand by to go to stand by : press the stand by button (stby) once. All rcvds05's will display '-'. Restart : press stand by key : last selected source will be displayed. Or p...

  • Page 57

    R5975765 rcvds05 020997 57 r5975765 rcvds05 020997 57 67% 212)) $8',2 3 ()$', * 67% 212)) operating instructions operating instructions when text is on, a bar scale and number indication will be displayed when activating an image control. When text is off, no indication will be displayed on the scre...

  • Page 58

    R5975765 rcvds05 020997 58 r5975765 rcvds05 020997 58 operating instructions operating instructions proceed as follow : - select a source. - adjust the audio pre-fading with the "+" and "-" pre-fading button. The adjusted level will be memorized by the rcvds05 and recalled every time this source is ...

  • Page 59

    R5975765 rcvds05 020997 59 r5975765 rcvds05 020997 59 operating instructions operating instructions where the chks is : (addr + cmd + dat1 + dat2 + dat3 + dat4)mod256. Only the least significant byte (mod256) of the sum (addr + cmd + dat1 + dat2 + dat3 + dat4) is used for the checksum. Because the n...

  • Page 60

    R5975765 rcvds05 020997 60 r5975765 rcvds05 020997 60 operating instructions operating instructions for communication from rcvds05 to computer, there is no acknowledgement available. However there is only communication in this direction after a request is sent from the computer to the rcvds05. It is...

  • Page 61

    R5975765 rcvds05 020997 61 r5975765 rcvds05 020997 61 operating instructions operating instructions the available commands : addr 01haddress rcvds is displayed on rcvds stdby 0eh standby num_0 10hnumeric keys num_1 11h " num_2 12h " num_3 13h " num_4 14h " num_5 15h " num_6 16h " num_7 17h " num_8 1...

  • Page 62

    R5975765 rcvds05 020997 62 r5975765 rcvds05 020997 62 operating instructions operating instructions "category ii" commands. Catii commands are commands which are not possible with the rcu. Read_source 4ah the rcvds05 will return to the currently selected source and source type. The dat1, dat2, dat3,...

  • Page 63

    R5975765 rcvds05 020997 63 r5975765 rcvds05 020997 63 operating instructions operating instructions read_pot 7ah reads the indicated eeprom-value of the current selected source. The eeprom value may be prefading, sharpness, hue (tint) or saturation. Computer to rcvds : stx offs adr cmd dat1 0 0 0 ch...

  • Page 64

    R5975765 rcvds05 020997 64 r5975765 rcvds05 020997 64 operating instructions operating instructions dat4 1 rcvds05 only answers ack or nack. Example : stx offs adr 79h 06 0 3ah 1 chks +offs the computer will update the sharpness to the value 3ah and write it into the eeprom for the current selected ...

  • Page 65

    R5975765 rcvds05 020997 65 r5975765 rcvds05 020997 65 operating instructions operating instructions block transfer eeprom to pc 72h send all the used bytes in the eeprom to the pc (168 bytes) pc to rcvds : stx offs adr 72h ffh ffh ffh ffh chks +offs rcvds to pc : ack adr 72h ffh ffh ffh ffh chks the...

  • Page 66

    R5975765 rcvds05 020997 66 r5975765 rcvds05 020997 66 operating instructions operating instructions read_version 4ch reads the software version of the eeprom of the rcvds05. Pc to rcvds : stx offs adr 4ch 0 0 0 0 chks +offs dat1 0 dat2 0 dat3 0 dat4 0 rcvds to pc : ack adr 4ch 20h dat2 dat3 0ch chks...

  • Page 67

    R5975765 rcvds05 020997 67 r5975765 rcvds05 020997 67 operating instructions operating instructions dat1 1 programming the output module dat2 1 programming for video 2 programming for s-video dat3 0 dat4 0 example : 3 rcvds05's linked and connected to one display, no decoder installed. The mode swit...

  • Page 68

    R5975765 rcvds05 020997 68 r5975765 rcvds05 020997 68 error codes error codes vii. Error codes during operation, the rcvds05 can display several error codes on its seven segment display. The f error codes ask for an intervention by the operator himself. The e error codes ask for a service interventi...

  • Page 69

    R5975765 rcvds05 020997 69 r5975765 rcvds05 020997 69 error codes error codes error e6 : i²c error, tda4670, call for technical assistance (decoder module). Error e7 : i²c error on decoder interface. Error codes error codes error e6 : i²c error, tda4670, call for technical assistance (decoder module...

  • Page 70

    R5975765 rcvds05 020997 70 r5975765 rcvds05 020997 70 optional decoder order number : 98 28030 a decoder can be installed for video, s-video or component video decoding. All signals are converted into rgb. The decoder must always be installed in the master rcvds05. So, in a multiple rcvds05 installa...