1. DL manuals
  2. Barco
  3. Projector
  4. RLM-W14
  5. Service Manual

Barco RLM-W14 Service Manual

Other manuals for RLM-W14: Quick Start Manual, User Manual
Manual is about: DLP DIGITAL PROJECTOR

Summary of RLM-W14

  • Page 1

    1 of 149 projector service manual barco rlm w14 rev.01.

  • Page 2

    2 of 149 dlp digital projector rev.01 revision description date rev.00 preliminary 7/4/2014 rev.01 chapter 2-2. Block diagram – page 11 chapter 5. Program setting and software download – page 72 chapter 8. Spart parts list & spare parts photo – page 121 chapter 6-4. Focus adjusting – page 112 8/4/20...

  • Page 3

    3 of 149 contents 1,compliance of safe repair .......................................................................... 5 1-1 cautions during disassembling and assembling ................................................. 6 1-2 lamp ......................................................................

  • Page 4

    4 of 149 7-4 replacing the filter ……….….………………………….….…….……………………..123 8. Spart parts list & spare parts photo ………..…………………………..……… 126 9. Product packaging …………………..……………………...……………….………….. 138 9-1 full set unit packaging ….…..………………………….……….……….………….…138 9-2 model accessory part.. ………………………………….………...

  • Page 5: Barco Rlm W14 Projector

    5 of 149 barco rlm w14 projector please note the information contained herein is based on the experience and knowledge relating to the subject matter gained by barco prior to publication. No patent license is granted by this information. Barco reserves the right to change this information without no...

  • Page 6

    6 of 149 1. Compliance of safe repair be sure to read this service manual before providing services. In the projector, full consideration is taken to ensure the safety for fire, electric shock, injury, harmful radiation, and substance. Therefore, observe the notice described in this service manual s...

  • Page 7

    7 of 149 2. Specifications this section provides technical information about the projector's performance. 2-1 specifications *item description projection system it is designed with dmd lvds 0.96" 1920*1200 1200p spd dc3 dlp tm 3-chips channel high-definition images projector. Resolution wuxga 1200p ...

  • Page 8

    8 of 149 projection lens r9862000-tld+ (0.73:1) r9840775-tld+ (1.2:1) r9862010-tld+ (1.5 - 2.0:1) r9862020-tld+ (2.0 – 2.8:1) r9862030-tld+ (2.8 – 4.5:1) r9862040-tld+ (4.5 – 7.5 :1) r9829997-tld+ (7.5 – 11.2:1) r9862005-tld+ ultra (1.25 – 1.6).

  • Page 9

    9 of 149 inputs / outputs ●hdmi input ●sdi/hdsd/3g input ●sdi/hdsd/3g output ●d-sub 15 input (rgbhv) ●hdbaset input (digital video) ●sync input ●sync output ●5-bnc input (rgbhv) ●3-rca input (ypbpr) ●rs-232 input (support rs-232 standard, firmware download, switch on & off, rs-232 commands) ●ir inpu...

  • Page 10

    10 of 149 temperature non- operating : -20~ 60 °c operating : 0~ 40 °c altitude non-operating : no definition operating : up to 3,000 m @ 25°c humidity non-operating : 90% operating : 0 ~ 90% dimensions 504.8 mm (w) x 631 mm (l) x 277 mm (h) weight 33.5 kg.

  • Page 11

    11 of 149 2-2 block diagram w14 wuxga 3d all boards' function block diagram.

  • Page 12

    12 of 149.

  • Page 13

    13 of 149 2-3 fan location fan.No connector type function normal eco fan0 fans e bd(cn635) 3pin afb0612hc-f00 rdmd cooling 3500 rpm 2900 rpm fan1 fans e bd(cn635) 4pin afb1212h-sm09 exhaust 2000 rpm 1500 rpm fan2 fans e bd(cn635) 5pin afb1212h-sm09 exhaust 1800 rpm 1500 rpm fan3 fans e bd(cn635) 6pi...

  • Page 14

    14 of 149.

  • Page 15: System Operation Commands

    15 of 149 3. Troubleshooting 3-1. Rs-232 protocol command  interface and requirements the rs-232 commands use only ascii characters which can be entered using a typical terminal emulator like windows hyperterminal with the following setting: bits per second: 115200 data bits: 8 parity: none stop bi...

  • Page 16

    16 of 149 for motor control like lens shift, focus and zoom, the parameters “ + ” and “ - ” are defined as follows. Command item command system action focus + - + => focus near, - => focus far zoomio + - + => zoom out - => zoom in vert.Offset + - + => up - => down horiz.Offset + - + => right - => le...

  • Page 17

    17 of 149 the lists of valid operation commands for barco rlm w14 are shown in below table. Barco rlm w14 operation commands command item operation commands values notes 1-1 input.Sel = ? 0 = hdmi 1 = hdbaset 2 = rgb d-15 3 = yuv 1 4 = rgbhv/yuv2 5 = reserve 6 = reserve 7 = reserve 8 = sdi/hdsdi/3g ...

  • Page 18

    18 of 149 barco rlm w14 operation commands command item operation commands values notes 2-4 (reserve) (reserve) (reserve) (reserve) 2-5 sharp = ? + - 0 - 200 note2 2-6 nr = ? + - 0 - 200 note2 2-7 color.Temp = ? 0 = 3200k 1 = 5400k 2 = 6500k 3 = 9300k 4 = native note2; note8; note20 2-8 red.Offset =...

  • Page 19

    19 of 149 barco rlm w14 operation commands command item operation commands values notes 2-20 color.Space2 = ? 0 = auto 1 = yuv hd 2 = yuv std 3 = rgb-pc (0-255) 4 = rgb-video (16-235) note2 3-1 zoom = ? 0 = off 1 = crop 2 = zoom note2; note6 3-2 pip.Sel = ? 1 = hdmi 2 = hdbaset 3 = rgb d-15 4 = yuv ...

  • Page 20

    20 of 149 barco rlm w14 operation commands command item operation commands values notes 4-6 lamp2.Stat ? 0 = off 1 = on note1 5-1 rear.Proj = ? 0 = front 1 = rear note1 5-2 ceil.Mode = ? 0 = floor 1 = ceiling note1 5-3 zoomio + - + = zoom out - = zoom in motor command; note1 5-4 focus + - + = focus ...

  • Page 21

    21 of 149 barco rlm w14 operation commands command item operation commands values notes 5-9 int.Ptrn = ? 0 = off 1 = color bars 2 = hatch 3 = burst 4 = red 5 = green 6 = blue 7 = white 8 = black 9 = ti-red 10 = ti-green 11 = ti-blue 12 = ti-ramp note1 5-10 color.Space = ? 0 = native 1 = ebu 2 = smpt...

  • Page 22

    22 of 149 barco rlm w14 operation commands command item operation commands values notes 5-22 blank.Left = ? + - 0 ~ 534 note1 5-23 blank.Right = ? + - 0 ~ 534 note1 5-23a blank.Rst (execute) note1 5-24 scen.Stat = ? 0 = off 1 = on note1 5-25 scen.Wht.Top scen.Wht.Btm = ? + - 0 ~ 500 note1;note16 5-2...

  • Page 23

    23 of 149 barco rlm w14 operation commands command item operation commands values notes 5-35 lens.Load = 1 = load memroy1 lens setting 2 = load memory2 lens setting 3 = load memory3 lens setting note1 5-36 lens.Save = 1 = save lens setting to memroy1 2 = save lens setting to memory2 3 = save lens se...

  • Page 24

    24 of 149 barco rlm w14 operation commands command item operation commands values notes 6-10 startup.Chime = ? 0 = off 1 = on 6-11 btn.1 = ? 0 = hdmi 1 = hdbaset 2 = rgb d-15 3 = yuv 1 4 = rgbhv/yuv2 5 = reserve 6 = reserve 7 = reserve 8 = sdi/hdsdi/3g 9 = stereo dvi 6-12 btn.2 = ? 0 = hdmi 1 = hdba...

  • Page 25

    25 of 149 barco rlm w14 operation commands command item operation commands values notes 6-14 btn.4 = ? 0 = hdmi 1 = hdbaset 2 = rgb d-15 3 = yuv 1 4 = rgbhv/yuv2 5 = reserve 6 = reserve 7 = reserve 8 = sdi/hdsdi/3g 9 = stereo dvi 6-15 btn.5 = ? 0 = hdmi 1 = hdbaset 2 = rgb d-15 3 = yuv 1 4 = rgbhv/y...

  • Page 26

    26 of 149 barco rlm w14 operation commands command item operation commands values notes 6-17 trig.2 = ? 0 = 5:4 1 = 4:3 2 = 16:10 3 = 16:9 4 = 1.88 5 = 2.35 6 = letterbox 7 = native 8 = unscaled 9 = auto note1 6-18 auto.Src = ? 0 = off 1 = on note1 6-19 lang = ? 0 = english 1 = french 2 = spanish 3 ...

  • Page 27

    27 of 149 barco rlm w14 operation commands command item operation commands values notes 7-4 act.Src ? 0 = hdmi 1 = hdbaset 2 = rgb d-15 3 = yuv 1 4 = rgbhv/yuv2 5 = reserve 6 = reserve 7 = reserve 8 = sdi/hdsdi/3g 9 = stereo dvi note1 7-5 pip.Src ? 0 = off 1 = hdmi 2 = hdbaset 3 = rgb d-15 4 = yuv 1...

  • Page 28

    28 of 149 barco rlm w14 operation commands command item operation commands values notes 7-18 hdbt.Txver ? Note1 8-1 cs_cust_rx = ? 000 ~ 999 p7 command; note1; note20 8-2 cs_cust_ry = ? 000 ~ 999 p7 command; note1; note20 8-3 cs_cust_gx = ? 000 ~ 999 p7 command; note1; note20 8-4 cs_cust_gy = ? 000 ...

  • Page 29

    29 of 149 barco rlm w14 operation commands command item operation commands values notes 8-12 cs_cust_my = ? 000 ~ 999 p7 command; note1; note20 8-13 cs_cust_yx = ? 000 ~ 999 p7 command; note1; note20 8-14 cs_cust_yy = ? 000 ~ 999 p7 command; note1; note20 0.1 picture.Mute = ? 0 = off 1 = on 0.2 powe...

  • Page 30

    30 of 149 barco rlm w14 operation commands command item operation commands values notes 0.6 errcode ? 0=errmsgovertempinlet 1=errmsgovertempdmd 2=errmsgovertemplamp1 3=errmsgovertemplamp2 4=errmsgovertempballast1 5=errmsgovertempballast2 6=errmsgfaniniterror 7=errmsgfan0rotateerror 8=errmsgfan1rotat...

  • Page 31

    31 of 149 barco rlm w14 operation commands command item operation commands values notes 0.7 f.Search = ? 0 = f1 search 1 = f2 search (default) 0.8 sdi.3gccir = ? 0 = trs 1 = ccir 0.9 darktm.Sel = ? 0 = 650 us 1 = 1300 us 2 = 1950 us note 19 0.10 3dsync.Inv = ? 0 = off 1 = on note 19 0.11 3dsync.Dly ...

  • Page 32

    32 of 149 note13: only mcu version number will be read back in standby mode. Note14: not applicable when the internal pattern is displayed. Note15: the summation of the absolute value of h.Keystone and v.Keystone should not be greater than 350. Note16: per geo semi’s specification, the minimum blend...

  • Page 33

    33 of 149 appendix 1: main select hdmi 1 hdbas et rgb d-15 yuv 1 rgbhv / yuv 2 sdi / hdsdi/3g pip select hdmi 1 - o o o - hdbaset - o o o - rgb d-15 o o - - o yuv 1 o o - - o rgbhv / yuv 2 o o - - o sdi / hdsdi/3g - - o o o o source available - na appendix 2: input format : 640x480_75hz_vga: 640x480...

  • Page 34

    34 of 149 appendix 3: the allowable combinations of warp, blanking and scenergix were summarized as the following table x indicates a not-allowed combination ok indicates a allowed combination.

  • Page 35

    35 of 149 3-2. Troubleshooting & error code error code definition in rs232 debug mode, the main formatter board & slave mcu will response with error code in case of system error like lamp fail, or thermal situation failure, etc. They are defined as below table. Error code message – troubleshooting a...

  • Page 36

    36 of 149 replace fan 7. 15 errmsgdmdinitfail – check and replace main formatter board, formatter board and dmd chip. 16 errmsglampinitfail – check and replace ballast 1. 17 errmsglamplitfail – check and replace lamp 1. 18 errmsgballastuarterror – check and replace ballast 1 and power board. 19 errm...

  • Page 37

    37 of 149 45 errmsgfan17rotateerror –– reserved & none for this model. 46 errmsgfan18rotateerror –– reserved & none for this model. 47 errmsgfan19rotateerror –– reserved & none for this model. 48 errmsgfan20rotateerror –– fan20 gets error during projector working. Check and replace fan 20. 49 errmsg...

  • Page 38

    38 of 149.

  • Page 39

    39 of 149.

  • Page 40

    40 of 149 4. Key part replacement & wire dressing 4-1 right cover & left cover loosen 8 screws on the left cover. Take out the left cover. Left cover loosen 8 screws on the right cover. Take out the right cover. Right cover.

  • Page 41

    41 of 149 4-2 top cover loosen 3 screws on the back of top cover. Loosen 4 screws on the right of top cover. Loosen 4 screws on the left of top cover. Open the top cover. Take out the top cover..

  • Page 42

    42 of 149 4-3 w2 board loosen 7 screws and unplug 4 connectors on the w2 board. Take out the w2 module. Take out the cover and loosen 4 screws on the w2 board. Take out the w2 board. Loosen 2 screws and unplug 1 connector ( cn4 ) on the main formatter board. Take out the fan..

  • Page 43

    43 of 149 4-4 main formatter board unplug 1 connector on the main formatter board . Unplug other 9 connectors on the main formatter board . Loosen 8 screws on the main formatter board . Take out the main formatter board..

  • Page 44

    44 of 149 4-5 fan c board unplug 5 connectors and loosen 2 screws on the fan c board . Take out the fan c board. Loosen 2 screws on the bracket . Take out the bracket. Loosen 17 screws on the i/o terminal..

  • Page 45

    45 of 149 4-6 fan e board & hd baset board & micor control board & rj-45 board loosen 2 screws and unplug 5 connectors on the fan e board. Take out the fan e board. Loosen 3 screws on the hdbaset board. Take out the hdbaset board. Unplug 23 connectors and loosen 3 screws on the micor control board. ...

  • Page 46

    46 of 149 disconnect the right connector under micro control board. Take out the micro control board. Unplug 1 connector and loosen 1 screw on the rj-45 board. Take out the rj-45 board..

  • Page 47

    47 of 149 4-7 video board & dual link dvi (3d) board loosen 1 screw under the right of the brace of video board. Loosen 1 screw under the left of the brace of video board. Take out the brace. Unplug 1 connector and loosen 2 screws on the dual link dvi (3d) board. Take out the dual link dvi (3d) boar...

  • Page 48

    48 of 149 unplug 1 connector on the video board. Loosen 3 screws on the right side of the video board. Loosen 4 screws on the left side of the video board. Take out the video board..

  • Page 49

    49 of 149 4-8 fan d board & bracket plate unplug the 2 connectors and loosen 2 screws on the fan d board. Take out the fan d board. Loosen 6 screws on the fip signal cable in the bracket. Take out the 2 group cables from concave space in the bracket. Take out the 2 group cables from fasten tie and 1...

  • Page 50

    50 of 149 4-9 fan b board & filter & lamp 1 & lamp 2 & fan 2 & fan 3 unplug the 5 connectors, and loosen 2 screws on the fan b board. Take out the fan b board. Loosen 2 screws on the ventilation slot of rear cover. Then, open the cover. Take out the filter. Loosen 2 screws on the ventilation slot of...

  • Page 51

    51 of 149 loosen 4 screws on the fan 2 & fan 3 module of back cover. Take out the fan 3 module. And, loosen 4 screws on it and open the cover, then loosen 4 plastic pin. Open fan 3 module. Loosen 2 screws on the fan 3, and then take off fan 3. Loosen 3 screws on lamp 2 module. Take out the lamp 2 mo...

  • Page 52

    52 of 149 take out the fan 2 module. And, loosen 4 screws on it and open the cover, then loosen 4 plastic pin. Open fan 2 module. Loosen 2 screws on the fan 2, and then take off fan 2. Loosen 3 screws on lamp 1 module. Take out the lamp 1 module. Take off the lamp1 & lamp 2 module ..

  • Page 53

    53 of 149 4-10 back cover & keypad & rear ir board loosen 4 screws on the right and bottom side of cover. Loosen 8 screws on the left side of cover and two fan modules. Take off the back cover. Loosen 4 screws and unplug 1 connector on the rear cover. Loosen 1 screw and unplug 1 connector on the rea...

  • Page 54

    54 of 149 4-11 fan 20 & fan 21 & fan 22 & fan 23 loosen 3 screws on the fan 20. Loosen 2 screws on the fan 20. Then, take off fan 20. Loosen 2 screws on the fan 21. Loosen 2 screws on the fan 21. Then, take off fan 21..

  • Page 55

    55 of 149 loosen 3 screws on the fan 22. Loosen 2 screws on the fan 22. Then, take off fan 22. Loosen 2 screws on the fan 23. Loosen 2 screws on the fan 23. Then, take off fan 23..

  • Page 56

    56 of 149 4-12 left cover & fan 1 loosen 13 screws on the left cover. Take off the left cover. Loosen 4 screws on the fan 1 module of left cover. Loosen 4 plastic pin on the fan 1 module of left cover. Unplug the cable from bracket and take off the fan 1..

  • Page 57

    57 of 149 4-13 ballast & dc-dc board & ac filter board & power board & fan 8 & fan 9 loosen 4 screws on the ballast module cover and then take off it. Unplug 3 connectors and loosen 4 screws on ballast. Then, take off it. Unplug 3 connectors and loosen 4 screws on ballast. Then, take off it. Take ou...

  • Page 58

    58 of 149 loosen 2 screws on the top of power module loosen 1 screw on the left bottom of power module. Loosen another 1 screw on the right bottom of power module raise the power module. Take off the power module. Open the power module..

  • Page 59

    59 of 149 unplug 1 connector from ac filter board. Unplug 2 connectors and loosen 4 screws on the ac filter board. Take off the ac filter board. Loosen 4 screws on the dc-dc board. Take off the dc-dc board. Loosen 2 screws on the inside bracket from power module..

  • Page 60

    60 of 149 take off the bracket. Loosen 2 screws on the top left side of power board. Loosen 3 screws on the bottom left side of power board. Loosen 3 screws on the left side of power board. Unplug 1 connector on power board and cable from concave of power module. Unplug 1 connector on power board an...

  • Page 61

    61 of 149 unplug 1 connector on power board and cable from fasten tie of power module. Take off the power board. Loosen 4 plastic pin on the fan 8 of power module. Take off the fan 8. Loosen 4 plastic pin on the fan 9 of power module. Take off the fan 9..

  • Page 62

    62 of 149 4-14 front cover & front ir board loosen 1 screw on right bottom side of front cover. Loosen 4 screws on the right side of right cover. Take off the front cover. Front cover unplug 1 connector and loosen 1 screw on front ir board. Take off the front ir board..

  • Page 63

    63 of 149 4-15 right cover & fan 0 loosen 14 screws on the right cover. Take off the right cover. Right cover loosen 2 screws on the bracket of fan 0. Loosen 4 plastic pin on the bracket of fan 0, then take off the fan0..

  • Page 64

    64 of 149 loosen 4 screws on the cover of fan 4. Take off the fan 4 cover. Loosen 3 screws on the fan 4. Take off the fan 4. Loosen 3 screws on the fan 5. Take off the fan 5..

  • Page 65

    65 of 149 4-16 motor driver board & lens mount loosen 4 screws and unplug 10 connectors on the motor driver board. Take off the motor driver board. Loosen 2 screws on the left side of lens mount. Loosen other 2 screws on the right side of lens mount. Take off the lens mount lens mount.

  • Page 66

    66 of 149 4-17 prism flow channel & light shutter & fip loosen 1 screw on the prism flow channel. Take off the prism flow channel. Loosen 2 screws on the light shutter. Take off the light shutter..

  • Page 67

    67 of 149 light shutter. Use t-type tool to screw up the fip tightly. Loosen first screw on the bottom side of fip. Loosen second screw on the bottom side of fip. Loosen third screw on the bottom side of fip. Take off the fip. Fip.

  • Page 68

    68 of 149 4-18 illumination & fan 6 & fan 7 & fan 10 & fan 11 loosen first screw on the bottom side of fan 11 bracket. Loosen second screw on the bottom side of fan 11 bracket. Take off the fan 11 module. Loosen 2 plastic pins on the fan 11 bracket. And, take off the fan11. Loosen 1 screw on the lef...

  • Page 69

    69 of 149 take off the illumination. Illumination loosen 2 screws on the bottom side of the fan 7 bracket. Take off the fan 7 module. Loosen 2 plastic pins on the fan 7 bracket. And, take off the fan 7. Loosen 2 screws on the bottom side of the fan 6 & fan 10 bracket..

  • Page 70

    70 of 149 take off the fan 6 & fan 10 module. Unplug the cable from fan 6 location of yellow concave. Loosen eight plastic pins on the fan 6 & fan 10 bracket. Fan 6 & fan 10 from bracket. Fan 6 & fan 10

  • Page 71

    71 of 149 4-19 all module layout.

  • Page 72

    72 of 149 5. Program setting and software download 5-1. Firmware downloads procedure for main formatter board: 5-1-1. Connect the ac power of the projector and have the projector in standby mode. 5-1-2. Connect the rs-232 cable between the projector and the pc. 5-1-3. Open the firmware upgrade tool ...

  • Page 73

    73 of 149 5-1-5. Click the “projector communication test” button for testing the communication with the projector. If everything is ok, the following status bar will be shown. 5-1-6. Click the “open file” button to activate the file selection dialog box and select barcow12.Txt (or barcow112.Txt) fil...

  • Page 74

    74 of 149 5-1-7. Click “upgrade sw” to start the firmware upgrades process. Prior to the firmware upgrade process, you will be prompted with a warning dialog box for confirmation and click “yes” to proceed the firmware upgrade process. 5-1-8. The firmware upgrade process indicator of micro-control b...

  • Page 75

    75 of 149 5-1-9. After finishing the firmware upgrade of the micro-control board (1 st part), the firmware upgrade process of the video board (2 nd part) will be shown as follows. 5-1-10. Depending on the file size of the firmware, it may take about 12 ~ 25 minutes before the firmware upgrading can ...

  • Page 76

    76 of 149 5-2. Firmware downloads procedure for sxw2 board: 5-2-1. Connect the ac power of the projector and have the projector in standby mode. 5-2-2. Connect the rs-232 cable between the projector and the pc. 5-2-3. Open a terminal program (e.G. Tera term) with the following setting, baud rate 115...

  • Page 77

    77 of 149 5-2-5. Close and exit the terminal program. 5-2-6. Activate the sxw2 firmware updater program for the firmware upgrade of sxw2 chip. And select “uart” in the “targets on” 5-2-7. Click “search” button, the available com port (likes com:1) will be listed after searching and shown as follows ...

  • Page 78

    78 of 149 5-2-9. After selecting the firmware file, press the “update firmware” to start the firmware upgrade process. 5-2-10. The firmware upgrade status will be shown on the status bar of the firmware updater to indicate the progress of this firmware download. 5-2-11. After finishing the firmware ...

  • Page 79

    79 of 149 5-3. Firmware downloads procedure for rj-45 board: 5-3-1. Connect the ac power of the projector and have the projector in standby mode. 5-3-2. Connect the rj-45 cable between the projector and the pc. And make sure that the two leds of the rj-45 module are lit after connecting the rj-45 ca...

  • Page 80

    80 of 149 5-3-6. Key in the ip address and followed by “/firmwareupdate.Htm” on the url box as below to activate the firmware update procedure http://192.168.0.100/firmwareupdate.Htm and click the “update” button to start the firmware upgrade process..

  • Page 81

    81 of 149 5-3-7. The following message will be shown on the display, click “continue” button to proceed 5-3-8. Press the “browse” button and locate the firmware (binary code) to be upgraded. Then press the “upgrade” button to proceed the download process. Browse.

  • Page 82

    82 of 149 5-3-9. Wait until the firmware upgrade process finished. 5-3-10. The following message will be shown after the firmware upgrade procedure. Just press the “re login” button to finish the whole firmware upgrade process of rj-45 module. Browse.

  • Page 83

    83 of 149 rj-45 test procedures key in your projector ip to web browser information.

  • Page 84

    84 of 149 5-4. Recover process procedure for nxp mcu:.

  • Page 85

    85 of 149.

  • Page 86

    86 of 149.

  • Page 87

    87 of 149.

  • Page 88

    88 of 149.

  • Page 89

    89 of 149.

  • Page 90

    90 of 149 5-5. Firmware downloads procedure for motor board: 1. Go to rs-232 interface, run command “ op dlmo ” and press “ enter ”. 2. Run " flash magic” 3. Set “select device” to lpc2132 4. Set com port, baud rate, oscillator. 5. Click “browse to choose file. 6. Click “start”.

  • Page 91

    91 of 149.

  • Page 92

    92 of 149.

  • Page 93

    93 of 149.

  • Page 94

    94 of 149 5-6. Firmware downloads procedure for ballast: 1. Use command “op dlba1” to download ballast 1. Use command “op dlba2” to download ballast 2. 2. Close tera term. Run serialupdate2.6e.Exe.

  • Page 95

    95 of 149 3. Press the ‘hex file” to select .Hex file..

  • Page 96

    96 of 149 4. Press the “change” to select “com port”..

  • Page 97

    97 of 149 5. Press “confirm” and “start” to download..

  • Page 98

    98 of 149 5-7. Firmware downloads procedure for hdbase t board: 1. Projector in standby mode 2. Use hdbaset download tool to download fw 1. Select com port and open. 2. Select download fw file. 3. Get hdbaset version in projector. 4. Start to download fw to projector..

  • Page 99

    99 of 149 after finishing downloading all software in projector, please go to osd to check your revision confirmation or go to rs-232 to command for confirmation. (a). Osd (b). Rs-232 please key in “op sw.Ver ?” and, you can get all software revision..

  • Page 100

    100 of 149 or, please key in “op soft.Version ?” and, you can get more detail software revision..

  • Page 101

    101 of 149 6. Adjustment 6-1. Fip convergence (cg) adjusting before cg adjust, please loose 1 pcs m3 screw. Then, please loose 2 m3 screw to remove the fan module..

  • Page 102

    102 of 149 to take the b dmd channel as the base to adjust g dmd channel for example: step1. Prepare 3 kinds of hexagonal wrenches step2. Use hexagonal wrenches to loosen 4 fixed screws..

  • Page 103

    103 of 149 step3. Use hexagonal wrenches to adjust first adjusting screw. Movement from top left to bottom right.

  • Page 104

    104 of 149 step4. Use hexagonal wrenches to adjust second adjusting screw. Movement from bottom left to top right.

  • Page 105

    105 of 149 step5. Use hexagonal wrenches to adjust third adjusting screw. Movement from bottom left to top right.

  • Page 106

    106 of 149 step6. After cg already finished adjusting, please screw up 4 fixed screws slowly backward and forward. Note: if you feel the adjusting screw is too tight or too loosing when you adjust, please try to adjust spring screw..

  • Page 107

    107 of 149 6-2. Folding mirror adjusting 1. Use 7 mm hex-sleeve screwdriver to adjust. 2. Check the full-white image where color band is, and slight adjust fixed-nut to remove it. 3. When finish adjusted, add tb1401b glue on the nuts to fix it. A c b (1) to adjust nut a to move the image vertically ...

  • Page 108

    108 of 149 6-3. P7 color calibration when you change main formatter board, please kindly do the p7 calibration. Make the image screen to 60 inch and put cl-200 in the center of screen. Setting: insert the eut rs-232 port and cl-200 rs-232 port plug into a pc or note book..

  • Page 109

    109 of 149 color temperature: native color space: native gamma: 2.2 lamp mode: normal lamp: dual open the cca_aas_w12.Exe “yes” open the rs-232 and please setup parameter of projector and cl-200 to link each other. Then, press “yes” to get ready..

  • Page 110

    110 of 149 after selecting the setting, please press to send data after sending data, please press to get data. Then, all data will be put into this area, and it also shows “pass” or “ng”. If it still show “ng”, please operate above steps again for p7 calibration..

  • Page 111

    111 of 149 after doing p7 calibration, please measure the below color temperature is in spec. Projector settings native mode zoom position barco lens 2-2.8 (wide) measurement position to get color coordinates of ansi 9points equipment minolta cl200a in normal mode or chroma 7600 specification x y wh...

  • Page 112

    112 of 149 6-4. Focus adjusting (a) (b) rotate the ring of zoom & focus. Because it makes the distance is 4 m from screen to lens and make sure image is square by moving projector, please make three label mark to align the one line. Focus zoom switch to “me” testing pattern to adjust focus. Use 13 m...

  • Page 113

    113 of 149 (c) (d) they can't appear gap. Use 13 mm inner hexagon sleeve screwdriver and 2.5 mm inner hexagon screwdriver (12 kg-f-cm) to screw up tightly 4 pcs rotating wheels of fixing focus screws. The surface of rotating wheels will touch the brace. But, they can’t appear gap and the rotating wh...

  • Page 114

    114 of 149 (e) after loosing slightly 4 pcs fixing lens mount screws, please use flat screwdriver to adjust left and right focus of whole image clearly. And, then adjust flare to make pixel of whole image clearly..

  • Page 115

    115 of 149 (f) (g) please use 3 mm inner hexagon screwdriver to adjust front and back focus of whole image clearly. And, then adjust flare to make pixel of whole image clearly. After adjusting all position focus of whole image, please use m5 cross screwdriver (10 kg-f-cm) to screw up tightly 4 pcs f...

  • Page 116

    116 of 149 (h) (i) please use “me” pattern to confirm all position focus and flare of whole image clearly. Please use 3.5mm cross torque screwdriver (4 kg-f-cm) to screw up the 2 pcs shaft on 4 pcs rotating wheels to fasten them..

  • Page 117

    117 of 149 7. Maintenance 7-1 cleaning the projector 7-1-1 cleaning the cabinet refer to the following guide to clean the projector cabinet. A. Wipe off dust with a clean dampened cloth. B. Moisten the cloth with warm water and mild detergent and wipe the cabinet. C. Rinse all detergent from the clo...

  • Page 118

    118 of 149 7-1-4 cleaning the optical parts carry out cleaning of the main unit and interior when replacing the lamp or making inspections. The glass cleaner used with the following parts is as follows. A) cleaning the projection lens: *when dust and fingerprints, etc. Are on the lens surface, use t...

  • Page 119

    119 of 149 7-2 replacing consumable parts during the course of normal usage, consumable parts become worn out resulting in reduced performance. The following guides detail how to replace the various consumable parts within the projector quickly and safely. Before replacing any of the parts, please t...

  • Page 120

    120 of 149 7-3 replacing the lamp.

  • Page 121

    121 of 149.

  • Page 122

    122 of 149.

  • Page 123

    123 of 149 7-4 replacing the filter.

  • Page 124

    124 of 149.

  • Page 125

    125 of 149.

  • Page 126

    126 of 149 8. Spart parts list & spare parts photo spare part list for rlm w14 item belong description barco p/n photo cover 1 only w14 cover al top w14 paint blk, rlm w14 r5001500k 2 only w14 cover al front w14 paint blk, rlm w14 r5001501k 3 only w14 cover al rear w14 paint blk, rlm w14 r5001502k.

  • Page 127

    127 of 149 4 only w14 cover al side right w14 assy , rlm w14 r5001503k 5 only w14 cover al side left w14 assy , rlm w14 r5001504k 6 only w14 cover al base w14 paint blk , rlm w14 r5001505k filter 1 only w14 filter kit, rlm w14.

  • Page 128

    128 of 149 fan 1 w12 & w14 bme k rlm w12 fan 7/11-r/b dmd r5001055k 2 w12 & w14 bme k rlm w12 fan 6/10-g/b dmd r5001068k 3 w12 & w14 bme k rlm w12 fan 20 - lamp r5001064k 4 w12 & w14 bme k rlm w12 fan 22 - lamp r5001065k 5 w12 & w14 bme k rlm w12 fan 21 - lamp r5001066k.

  • Page 129

    129 of 149 6 w12 & w14 bme k rlm w12 fan 23 - lamp r5001067k 7 w12 & w14 bme k rlm w12 fan 8 - pwr/ball r5001042k 8 w12 & w14 bme k rlm w12 fan 2/3 - exh r5001049k 9 w12 & w14 bme k rlm w12 fan 1/9-exh/pwr r5001050k 10 w12 & w14 bme k rlm w12 fan 4 - prism r5001051k.

  • Page 130

    130 of 149 11 w12 & w14 bme k rlm w12 fan 5-engine in r5001052k 12 w12 & w14 bme k rlm w12 fan 0 - r dmd r5001056k 13 w12 & w14 bme k rlm w12 fan-r1 - fpga r5001057k 14 w12 & w14 blk rlm w12 fan-12 r5001060k pcba 1 w12 & w14 bme k rlm w12 & w14 horz sensor bd r5001080k.

  • Page 131

    131 of 149 2 w12 & w14 bme k rlm w12 & w14 vert sensor bd r5001081k 3 w14 blk rlm w14 pwb assy main fornatter bd r5001507k 4 w14 blk rlm w14 ttl lvl motor bd r5001508k 5 w12 & w14 bme k rlm w12 & w14 driver b r5001082k.

  • Page 132

    132 of 149 6 w12 & w14 bme k rlm w12 & w14 fan driver c r5001084k 7 w14 blk rlm w14 fan driver d r5001509k 8 w12 & w14 bme k rlm w12 & w14 fan driver e r5001094k 9 w12 & w14 bme k rlm w12 & w14 main power bd r5001103k.

  • Page 133

    133 of 149 10 w12 & w14 bme k rlm w12 & w14 dc-dc bd r5001098k 11 w12 & w14 bme k rlm w12 & w14 keypad board r5001089k 12 w12 & w14 bme k rlm w12 & w14 ir bd r5001087k 13 w12 & w14 bme k rlm w12 & w14 slide sw r5001100k.

  • Page 134

    134 of 149 14 w14 blk rlm w14 uc control board r5001510k 15 w14 blk rlm w14 rj-45 board r5001511k 16 w14 blk rlm w14 dual link dvi bd r5001512k 17 w14 blk rlm w14 hdbase t board r5001513k 18 w12 & w14 bme k rlm w12 & w14 w2_tdms board r5001108k.

  • Page 135

    135 of 149 19 w14 blk rlm w14 video board r5001514k 20 w14 blk rlm w14 lamp driver 465w r5001515k optic module 1 w14 blk rlm w14 fip assy wuxga r5001516k.

  • Page 136

    136 of 149 2 w14 blk rlm w14 lens holder r5001517k 3 w12 & w14 bme k rlm w12 & w14 shutter assy r5001077k 4 w14 blk rlm w14 lmp 465w.

  • Page 137

    137 of 149 accessories 1 w14 blk rlm w14 remote controller 26keys r5001519k 2 accessor kit, rlm w14 (no battery) tbd.

  • Page 138

    138 of 149 9. Product packaging 9-1. Full set unit packaging.

  • Page 139

    139 of 149 9-2. Model accessory part.

  • Page 140

    140 of 149 9-3. Carton.

  • Page 141

    141 of 149 9-4. Serial no. & label explanation.

  • Page 142

    142 of 149 9-5. Air & sea shipping packaging.

  • Page 143

    143 of 149 appendix. Timing table a. Signal requirement all signal must be available with chroma signal a full white pattern, chroma pattern #41 signal b full black pattern,chroma pattern #11 signal c color bars: eight 100 pixel wide bars. Signal d crosshatch, chroma pattern #1. B. Timing of input s...

  • Page 144

    144 of 149 timing of input signale p o r s video q vertical a : h-total time o : v-total time b : h-sync pulse width p : p: v-sync pulse width c : h-back porch q : v-back porch d : h-display time r : v-display time e : h-front porch s : v-front porch video d b a e c.

  • Page 145

    145 of 149 c. Timing table signal format resolution frame rate 3 r c a y -pr -pb 5 bnc r gbh v vg a 5 bnc y uv hdmi/digital video r gb 8 -b it y uv 10 -b it y uv 12 -b it y uv pc 640x480 59.94 x x x 640x480 74.99 x x x 640x480 85 x x x 800x600 60.32 x x x 800x600 75 x x x 800x600 85.06 x x x 848x480...

  • Page 146

    146 of 149 832x624 74.54 x x x secam secam (m) 50 sdtv rgbs 50 480i 59.94 x x 1440x480i 60 x x x x 1440x576i 50 x x x x 576i 50 x x edtv 480p 59.94 x x x x x x x x 576p 50 x x x x x x x x hdtv 1035i 60 x x x x x x x x 1080i 50 x x x x x x x x 1080i (aus) 50 x x x x x x x x 1080i 59.94 x x x x x x x ...

  • Page 147

    147 of 149 1080p30 hd smpte 292m 1.5gbps hd ycbcr 4:2:2 10 1080p25 hd smpte 292m 1.5gbps hd ycbcr 4:2:2 10 1080i50 hd smpte 292m 1.5gbps hd ycbcr 4:2:2 10 1080p24 hd smpte 292m 1.5gbps hd ycbcr 4:2:2 10 720p60 hd smpte 292m 1.5gbps hd ycbcr 4:2:2 10 720p50 hd smpte 292m 1.5gbps hd ycbcr 4:2:2 10 108...

  • Page 148

    148 of 149 detail of timing chart timing name freq. H(khz) freq. V(hz) clock (m hz) h period h display h sync h backp v total v display v sync v backp 640*480-60 31.47 59.93 25.175 800 640 96 40 525 480 2 25 800*600-60 37.88 60.32 40 1056 800 128 88 628 600 4 23 848*480-47.95 23.674 47.95 25 1056 84...

  • Page 149

    149 of 149 1920x1200 61.816 49.93 158.25 2560 1920 200 320 1238 1200 6 29 1400x1050 65.517 59.98 121.75 1864 1400 144 232 1089 1050 4 32 1035i 33.75 60 74.25 2200 1920 44 148 562 517 5 35 1080i 28.13 50 74.25 2640 1920 44 148 562 540 5 15 1080i (aus ) 31.25 50 72 2304 1920 168 184 625 540 5 57 1080i...