1. DL manuals
  2. Barco
  3. Projector
  4. SERIAL COMMUNICATION LCD PROJECTOR
  5. User Manual

Barco SERIAL COMMUNICATION LCD PROJECTOR User Manual

Manual is about: SERIAL COMMUNICATION LCD PROJECTOR

Summary of SERIAL COMMUNICATION LCD PROJECTOR

  • Page 1

    Barco projection systems barco projection systems date: 10.04.98 r5975236_r03 date: 10.04.98 r5975236_r03 serial communication lcd projector user's manual serial communication lcd projector user's manual.

  • Page 2

    I-1 i-1 user's manual r5975236-r3 user's manual r5975236-r3 contents contents.

  • Page 3

    I-2 i-2 user's manual r5975236-r3 user's manual r5975236-r3 chapter 1 : communication basics. Communication protocol .......................................... 1-3 communication settings .......................................... 1-4 hardware ............................................................

  • Page 4

    I-3 i-3 user's manual r5975236-r3 user's manual r5975236-r3 treble, increment ....................................................2-40 volume, decrement .................................................2-41 volume, increment ..................................................2-42 chapter 3 : advanced...

  • Page 5

    I-4 i-4 user's manual r5975236-r3 user's manual r5975236-r3 lock audio, read .....................................................3-57 lock audio, write .....................................................3-59 phase, read ............................................................3-61 phase, write...

  • Page 6

    1-1 1-1 user's manual r5975236-r3 user's manual r5975236-r3 chapter 1: communication basics chapter 1: communication basics.

  • Page 7

    1-2 1-2 user's manual r5975236-r3 user's manual r5975236-r3 communication protocol summary start byte \xfe projector address command byte(s) data bytes (optional) checksum byte stop byte \xff start byte the “start byte” informs the projector (in case of transmission) or the computer (in case of rece...

  • Page 8

    1-3 1-3 user's manual r5975236-r3 user's manual r5975236-r3 checksum byte the “checksum byte” is used to detect errors during transmission or reception. Formula : checksum byte = (projector address + command bytes + data bytes) modulo 256 stop byte the “stop byte” informs the projector (in case of t...

  • Page 9

    1-4 1-4 user's manual r5975236-r3 user's manual r5975236-r3 communication settings summary baud rate see baudrate table data bits 8 parity no stop bits 1 baud rate defines the speed of the data transfer. The baud rate can be set using the dip switches on the processor board of the projector. Before ...

  • Page 10

    1-5 1-5 user's manual r5975236-r3 user's manual r5975236-r3 baud rate table bd5000, bd5000lc, bd8000 s1:4 s1:3 s1:2 s1:1 baud rate (baud) off off off off 50 off off off on 75 off off on off 100 off off on on 110 off on off off 150 off on off on 200 off on on off 300 off on on on 600 on off off off 1...

  • Page 11

    1-6 1-6 user's manual r5975236-r3 user's manual r5975236-r3 connector labelled “rs232 in” this female d9-pin connector is used to connect the projector with the computer. Connector labelled “rs232 out” this male d9-pin connector is used to drive the next projector in a chain. Pin-out the pin-out is ...

  • Page 12

    1-7 1-7 user's manual r5975236-r3 user's manual r5975236-r3 chapter 1: communications basics hardware cable (ibm pc or compatible projector): chapter 1: communications basics hardware cable (ibm pc or compatible projector): 56,1 56287 &2003257 $8',2287 &75/ '(&2'(5 0$&,1387 9,'(2,1387 9, '(2 69,'(2 ...

  • Page 13

    1-8 1-8 user's manual r5975236-r3 user's manual r5975236-r3 cable (ibm pc or compatible projector) : 1 1 cd cd 2 2 rxd rxd 3 3 txd txd 4 4 dtr dtr d9 5 5 d9 female gnd gnd male 6 6 dsr dsr 7 7 rts rts 8 8 cts cts 9 9 ri ri order number r9827560 (cable length = 15m) order number r9872570 (cable lengt...

  • Page 14

    1-9 1-9 user's manual r5975236-r3 user's manual r5975236-r3 chapter 1: communications basics hardware cable (mac projector) : chapter 1: communications basics hardware cable (mac projector) : 56,1 56287 &2003257 $8',2287 &75/ ' ( & 2' ( 5 0 $ &,1 3 8 7 9 ,' ( 2,13 8 7 9,'(2 6 9 , '(2 9 *$ ,1 3 8 7 r...

  • Page 15

    1-10 1-10 user's manual r5975236-r3 user's manual r5975236-r3 cable (mac projector) : 1 4 hsko dtr 2 8 hski cts 3 3 txd- txd 4 5 gnd gnd din 5 2 d9 mini 8 rxd- rxd male 6 txd+ 7 n.C. 8 rxd+ order number r9827640 (d9-din mini8; cable length = 1m) order number r9827560 (d9-d9; cable length = 15m) orde...

  • Page 16

    1-11 1-11 user's manual r5975236-r3 user's manual r5975236-r3 length \x0b ‘h’ \x68 ‘e’ \x65 ‘l’ \x6c ‘l’ \x6c ‘o’ \x6f \x20 ‘w’ \x77 ‘o’ \x6f ‘r’ \x72 ‘l’ \x6c ‘d’ \x64 characters in this manual, all characters are expressed using the c-language syntax : decimal values ddd ddd = 0..255 hexadecimal v...

  • Page 17

    1-12 1-12 user's manual r5975236-r3 user's manual r5975236-r3 filename a filename is specified as a c-language string. This string has to follow some rules: filename 0 1 2 3 4 5 6 7 8 9 10 11 12 x x x x x x x x . Y z z null length string = 12 x = character of the base name (= 8 characters) ‘a’ ‘b’ ‘...

  • Page 18

    2-1 2-1 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands chapter 2: elementary commands chapter 2: elementary commands.

  • Page 19

    2-2 2-2 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands balance, decrement description decrement balance. Command command[0] \x23 command[1] \x0a data no data bytes. Projector type bd2100., bd2100lc, bd3000, bd300lc, bd3100., bd3100lc...

  • Page 20

    2-3 2-3 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description increment balance. Command command[0] \x22 command[1] \x0a data no data bytes. Projector type bd2100., bd2100lc, bd3000, bd300lc, bd3100., bd3100lc example increment ...

  • Page 21

    2-4 2-4 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands bass, decrement description decrement bass. Command command[0] \x23 command[1] \x08 data no data bytes. Projector type bd2100., bd2100lc, bd3000, bd300lc, bd3100., bd3100lc examp...

  • Page 22

    2-5 2-5 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands bass, increment bass, increment description increment bass. Command command[0] \x22 command[1] \x08 data no data bytes. Projector type bd2100., bd2100lc, bd3000, bd300lc, bd3100....

  • Page 23

    2-6 2-6 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands brightness, decrement brightness, decrement description decrement brightness. Command command[0] \x04 data no data bytes. Projector type bd2100., bd2100lc, bd3000, bd300lc, bd310...

  • Page 24

    2-7 2-7 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands brightness, increment brightness, increment description increment brightness. Command command[0] \x03 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100...

  • Page 25

    2-8 2-8 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands color, decrement color, decrement description decrement color (saturation). Command command[0] \x06 data no data bytes. Projector type bd5000, bd5000lc, bd8000, bd8000lc, bg8100 ...

  • Page 26

    2-9 2-9 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands color, increment color, increment description increment color (saturation). Command command[0] \x05 data no data bytes. Projector type bd5000, bd5000lc, bd8000, bd8000lc, bg8100 ...

  • Page 27

    2-10 2-10 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands contrast, decrement contrast, decrement description decrement contrast. Command command[0] \x02 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd...

  • Page 28

    2-11 2-11 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands contrast, increment contrast, increment description increment contrast. Command command[0] \x01 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd...

  • Page 29

    2-12 2-12 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description simulation of the infrared remote control unit. The codes act in the same way as if they were sent by an infrared remote control unit or the local keypad. Command c...

  • Page 30

    2-13 2-13 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands color- \x2d contrast \x25 contrast+ \x28 contrast- \x29 enter \x0a exit \x08 freez \x1b help \x09 mute \x1f pause \x0f phase \x32 phase+ \x34 phase- \x35 sharpness \x33 sharpne...

  • Page 31

    2-14 2-14 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd5100lc, bd8000, bd8000lc, bd8100, bd8100lc, bg8100, bg8100lc example select sour...

  • Page 32

    2-15 2-15 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description disable audio mute. Command command[0] \x26 command[1] \x3d data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc example disable a...

  • Page 33

    2-16 2-16 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description enable audio mute. Command command[0] \x27 command[1] \x3d data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc example enable aud...

  • Page 34

    2-17 2-17 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description disable video mute. Command command[0] \x26 command[1] \x3e data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc, bd5100, bd5100lc...

  • Page 35

    2-18 2-18 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description enable video mute. The on-screen-display will be muted too ! Command command[0] \x27 command[1] \x3e data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd...

  • Page 36

    2-19 2-19 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description decrement phase. Command command[0] \x0c data no data bytes. Projector type bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd5100lc, bd8000, bd8000lc, bd8100, bd8100lc...

  • Page 37

    2-20 2-20 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description increment phase. Command command[0] \x0b data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd5100lc,...

  • Page 38

    2-21 2-21 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description read the projector status. Command command[0] \x67 data no data bytes. Return data the return data consists of one data byte containing the projector status. Only b...

  • Page 39

    2-22 2-22 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands example read the status of a projector with address \x01. Suppose the status is projector on, text on, video mute off, picture freezed and no 800-peripheral connected. Transmit...

  • Page 40

    2-23 2-23 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description set the projector off. Command command[0] \x66 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd5...

  • Page 41

    2-24 2-24 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description set the projector on. Command command[0] \x65 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd51...

  • Page 42

    2-25 2-25 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description decrement sharpness. Command command[0] \x0a data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd510...

  • Page 43

    2-26 2-26 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands sharpness, increment description increment sharpness. Command command[0] \x09 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc, bd5000, bd...

  • Page 44

    2-27 2-27 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description read active source or slot. Command command[0] \x32 data no data bytes. Return data source or slot number (\x01..). Data[0] bd2100 \x01..\x09 bd2100lc \x01..\x09 bd...

  • Page 45

    2-28 2-28 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands source/slot, read number example read the active source/slot number of a projector with address \x01. Suppose the answer is \x03. Transmit start \xfe projector address \x01 com...

  • Page 46

    2-29 2-29 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description select a source or slot. Command command[0] \x31 data source or slot number (\x01..). Data[0] bd2100 \x01..\x09 bd2100lc \x01..\x09 bd3000 \x01..\x03 bd3000lc \x01....

  • Page 47

    2-30 2-30 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands source/slot, write number example select source 1 of a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \x31 data[0] \x01 checksum \x32 stop \...

  • Page 48

    2-31 2-31 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description : read active source or slot number and its mode. Command : command[0] \x34 data : no data bytes. Return data : data[0] = source or slot number (\x01..). Data[0] bd...

  • Page 49

    2-32 2-32 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands data[1] = source or slot mode (\x00 or \x01) video/s-video input data[1] mode \x00 video \x01 s-video rgb analog input - separate sync data[1] mode \x00 h/c : composite sync or...

  • Page 50

    2-33 2-33 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands example: read the active source/slot number+mode of a projector with address \x01. Suppose the source number equals \x03 and its mode equals \x01. Transmit start \xfe projector...

  • Page 51

    2-34 2-34 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands source/slot, write number+mode description: select a source or slot and put it in a pre-defined mode (mode selection is optional). Command: command[0] \x33 data: data[0] = sour...

  • Page 52

    2-35 2-35 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands data[1] = source or slot mode (\x00 or \x01) optional video/s-video input data[1] mode \x00 video \x01 s-video rgb analog input - separate sync data[1] mode \x00 h/c: composite...

  • Page 53

    2-36 2-36 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands example: select source 1, mode 1 of a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \x33 data[0] \x01 data[1] \x01 checksum \x36 stop \xff ...

  • Page 54

    2-37 2-37 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description decrement tint (hue). Command command[0] \x08 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc,bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd510...

  • Page 55

    2-38 2-38 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description increment tint (hue). Command command[0] \x07 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc,bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd510...

  • Page 56

    2-39 2-39 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description decrement treble. Command command[0] \x23 command[1] \x09 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc example decrement t...

  • Page 57

    2-40 2-40 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description increment treble. Command command[0] \x22 command[1] \x09 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc example increment t...

  • Page 58

    2-41 2-41 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description decrement volume. Command command[0] \x23 command[1] \x07 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc example decrement v...

  • Page 59

    2-42 2-42 user's manual r5975236-r3 user's manual r5975236-r3 chapter 2: elementary commands chapter 2: elementary commands description increment volume. Command command[0] \x22 command[1] \x07 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd300lc, bd3100, bd3100lc example increment v...

  • Page 60

    3-1 3-1 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands chapter 3: advanced commands chapter 3: advanced commands.

  • Page 61

    3-2 3-2 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the actual balance value. Command command[0] \x21 command[1] \x0a data no data bytes. Return data data[0] = balance value. Data[0] \xea..\x16 projector type bd2100, ...

  • Page 62

    3-3 3-3 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands balance, read balance, read receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector addr...

  • Page 63

    3-4 3-4 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description write a new balance value. Command command[0] \x20 command[1] \x0a data data[0] = balance value. Data[0] \xea..\16 projector type bd2100, bd2100lc, bd3000, bd3000lc, bd31...

  • Page 64

    3-5 3-5 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands bass, read bass, read description read the actual bass value. Command command[0] \x21 command[1] \x08 data no data bytes. Return data data[0] = bass value. Data[0] \xfc..\x05 project...

  • Page 65

    3-6 3-6 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands bass, read bass, read receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x...

  • Page 66

    3-7 3-7 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands bass, write bass, write description write a new bass value. Command command[0] \x20 command[1] \x08 data data[0] = bass value. Data[0] \xfc..\x05 projector type bd2100, bd2100lc, bd3...

  • Page 67

    3-8 3-8 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the actual brightness value. Command command[0] \x21 command[1] \x02 data no data bytes. Return data data[0] = brightness value. Data[0] bg8100 \x00..\xff bg8100lc o...

  • Page 68

    3-9 3-9 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands brightness, read brightness, read receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projecto...

  • Page 69

    3-10 3-10 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description write a new brightness value. Command command[0] \x20 command[1] \x02 data data[0] = brightness value. Data[0] bg8100 \x00..\xff bg8100lc otherwise \x00..\x3f projector...

  • Page 70

    3-11 3-11 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (acknowledge) start \xfe projector address \x01 command[0] \...

  • Page 71

    3-12 3-12 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands contrast, read contrast, read description read the actual contrast value. Command command[0] \x21 command[1] \x01 data no data bytes. Return data data[0] = contrast value. Data[0] ...

  • Page 72

    3-13 3-13 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands contrast, read contrast, read projector type bd2100, bd2100lc, bd3000, bd3000lc, bd3100, bd3100lc, bd5000, bd5000lc, bd5100, bd5100lc, bd8000, bd8000lc, bd8100, bd8100lc, bg8100, b...

  • Page 73

    3-14 3-14 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description write a new contrast value. Command command[0] \x20 command[1] \x01 data data[0] = contrast value. Data[0] bd2100 \x00..\x3f bd2100lc \x00..\x3f bd3000 \x00..\x40 bd300...

  • Page 74

    3-15 3-15 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands contrast, write contrast, write example set the contrast to \x30 on a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \x20 command[1] \x01 data[0...

  • Page 75

    3-16 3-16 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands dimming, decrement dimming, decrement description decrement dimming. Command command[0] \x23 command[1] \x0d data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd3000lc, ...

  • Page 76

    3-17 3-17 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands dimming, increment dimming, increment description increment dimming. Command command[0] \x22 command[1] \x0d data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd3000lc, ...

  • Page 77

    3-18 3-18 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description: decrement the fade value of the external speaker(s). The audio volume level of the external speaker(s) will decrease. Command : command[0] \x23 command[1] \x41 data : ...

  • Page 78

    3-19 3-19 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : increment the fade value of the external speaker(s). The audio volume level of the external speaker(s) will increase. Command : command[0] \x22 command[1] \x41 data :...

  • Page 79

    3-20 3-20 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : read the actual fade value of the external speaker(s). Command : command[0] \x21 command[1] \x41 data : no data bytes. Return data : data[0] = fade value. Data[0] \x0...

  • Page 80

    3-21 3-21 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands fade audio extern, read receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector addres...

  • Page 81

    3-22 3-22 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : write a new fade value for the extern speaker(s). Command : command[0] \x20 command[1] \x41 data : data[0] = fade value. Data[0] \x00..\x0f projector type : bd2100, b...

  • Page 82

    3-23 3-23 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff fade audio extern, write receive (acknowledge) start \xfe projector ...

  • Page 83

    3-24 3-24 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands fade audio intern, decrement description : decrement the fade value of the internal speaker. The audio volume level of the internal speaker will decrease. Command : command[0] \x23...

  • Page 84

    3-25 3-25 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : increment the fade value of the internal speaker. The audio volume level of the internal speaker will increase. Command : command[0] \x22 command[1] \x40 data : no da...

  • Page 85

    3-26 3-26 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : read the actual fade value of the internal speaker. Command : command[0] \x21 command[1] \x40 data : no data bytes. Return data : data[0] = fade value. Data[0] \x00.....

  • Page 86

    3-27 3-27 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x21 c...

  • Page 87

    3-28 3-28 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : write a new fade value for the intern speaker. Command : command[0] \x20 command[1] \x40 data : data[0] = fade value. Data[0] \x00..\x0f projector type : bd2100, bd21...

  • Page 88

    3-29 3-29 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff fade audio intern, write receive (acknowledge) start \xfe projector ...

  • Page 89

    3-30 3-30 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : copy file1 to file2. - file2 (destination file) has to be a custom file. - if the location specified by the “file index” of file2 has already been taken up, file2 wil...

  • Page 90

    3-31 3-31 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands transmit start \xfe projector address \x01 command[0] \xc2 data[0] \x6e (= ‘n’) data[1] \x74 (= ‘t’) data[2] \x73 (= ‘s’) data[3] \x63 (= ‘c’) data[4] \x20 (= ‘ ‘) data[5] \x20 (= ...

  • Page 91

    3-32 3-32 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : delete one or more files. - only custom files (????????.C??) can be deleted. Command : command[0] \xc1 data : one or more filenames (wildcards allowed). Projector typ...

  • Page 92

    3-33 3-33 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands example : delete all files starting with the characters “nt” on a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \xc1 data[0] \x6e (= ‘n’) data[...

  • Page 93

    3-34 3-34 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : get a list of files. Command : command[0] \xc0 data : one or more filenames (wildcards allowed). Projector type : bd2100, bd2100lc, bd3000, bd3000lc, bd3100 v1.06 , b...

  • Page 94

    3-35 3-35 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands file, list example : get a list of all files starting with the characters “nt” on a projector with address \x01. Suppose there are 2 files : “ntsc .S02” and “ntsc_rgb.C01”. Transmi...

  • Page 95

    3-36 3-36 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands file, list receive (answer) start \xfe projector address \x01 command[0] \xc0 data[0] \x6e (= ‘n’) data[1] \x74 (= ‘t’) data[2] \x73 (= ‘s’) data[3] \x63 (= ‘c’) data[4] \x20 (= ‘ ...

  • Page 96

    3-37 3-37 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : get the filename of the active file. Command : command[0] \xc5 data : no data bytes. Projector type : bd2100, bd2100lc, bd3000, bd3000lc, bd3100 v1.06 , bd3100lc v1.0...

  • Page 97

    3-38 3-38 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \xc5 d...

  • Page 98

    3-39 3-39 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : move file1 to file2. - only custom files can be moved. - if the location specified by the “file index” of file2 has already been taken up, file2 will overwrite that c...

  • Page 99

    3-40 3-40 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands transmit start \xfe projector address \x01 command[0] \xc4 data[0] \x6e (= ‘n’) data[1] \x74 (= ‘t’) data[2] \x73 (= ‘s’) data[3] \x63 (= ‘c’) data[4] \x20 (= ‘ ‘) data[5] \x20 (= ...

  • Page 100

    3-41 3-41 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff file, move receive (acknowledge) start \xfe projector address \x01 c...

  • Page 101

    3-42 3-42 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : rename file1 to file2. - only custom files can be renamed. - only the base name of a file can be renamed. This means that file1 and file2 have to point to the same lo...

  • Page 102

    3-43 3-43 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands transmit start \xfe projector address \x01 command[0] \xc3 data[0] \x6e (= ‘n’) data[1] \x74 (= ‘t’) data[2] \x73 (= ‘s’) data[3] \x63 (= ‘c’) data[4] \x20 (= ‘ ‘) data[5] \x20 (= ...

  • Page 103

    3-44 3-44 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands file, rename receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (acknowledge) start \xfe projector address \x01...

  • Page 104

    3-45 3-45 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands freeze, write off freeze, write off description disable freeze. Command command[0] \x26 command[1] \x23 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd3000lc, bd310...

  • Page 105

    3-46 3-46 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands freeze, write on freeze, write on description enable freeze. Command command[0] \x27 command[1] \x23 data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd3000lc, bd3100, ...

  • Page 106

    3-47 3-47 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands installation, read installation, read description read installation. Command command[0] \x21 command[1] \x24 data no data bytes. Return data data[0] = installation. Installation da...

  • Page 107

    3-48 3-48 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands installation, read installation, read receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe pr...

  • Page 108

    3-49 3-49 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands installation, write installation, write description write installation (front/table, ...). Command command[0] \x20 command[1] \x24 data data[0] = installation. Installation data[0]...

  • Page 109

    3-50 3-50 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the lamp run time in hours. Command command[0] \x64 data no data bytes. Return data the return data-transfer being the lamp run time in hours contains of four data...

  • Page 110

    3-51 3-51 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands lamp, read run time lamp, read run time receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe ...

  • Page 111

    3-52 3-52 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands lamp, read serial number lamp, read serial number description read the serial number of the lamp. Command command[0] \x63 data no data bytes. Return data the return data-transfer b...

  • Page 112

    3-53 3-53 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands lamp, read serial number lamp, read serial number receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) s...

  • Page 113

    3-54 3-54 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the lamp status. Command command[0] \x6c data no data bytes. Return data data[0] = lamp status. Only bit0 (least significant bit) is significant. Bit# bit = 0 bit ...

  • Page 114

    3-55 3-55 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands lamp, read status lamp, read status receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe proj...

  • Page 115

    3-56 3-56 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description reset the lamp run time (after installation of a new lamp). Command command[0] \x68 data the data being the lamp serial number is a pascal-language string (see syntax) ...

  • Page 116

    3-57 3-57 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the status of the audio lock. Command command[0] \x21 command[1] \x3f data no data bytes. Return data data[0] = lock specification. Lock data[0] off \x00 input 1 o...

  • Page 117

    3-58 3-58 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands lock audio, read lock audio, read receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projec...

  • Page 118

    3-59 3-59 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands lock audio, write lock audio, write description lock the audio signal to a specific audio input or set the lock off (audio input follows the video input). Command command[0] \x20 c...

  • Page 119

    3-60 3-60 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands lock audio, write lock audio, write receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (acknowledge) start \xfe...

  • Page 120

    3-61 3-61 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands phase, read phase, read description read the actual phase value. Command command[0] \x21 command[1] \x06 data no data bytes. Return data data[0] = phase value. Data[0] bd2100 \x00....

  • Page 121

    3-62 3-62 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands phase, read phase, read example read the actual phase value of a projector with address \x01. Suppose the phase equals \x03. Transmit start \xfe projector address \x01 command[0] \...

  • Page 122

    3-63 3-63 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands phase, write phase, write description write a new phase value. Command command[0] \x20 command[1] \x06 data data[0] = phase value. Data[0] bd2100 \x00..\xff bd2100lc \x00..\xff bd3...

  • Page 123

    3-64 3-64 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands phase, write phase, write example set the phase to \x03 on a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \x20 command[1] \x06 data[0] \x03 ch...

  • Page 124

    3-65 3-65 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands programmable blanking, write description write blanking shapes (circles and rectangles) (optional) command command[0] \xel data data for a solid circle with centre (x, y) and radiu...

  • Page 125

    3-66 3-66 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands data for a solid rectangle with coordinates (x1, y1)(x2, y2). Data data[n] 'r'='\x52' data[n+1] x1(msb) data[n+2] x1(lsb) data[n+3] y1(msb) data[n+4] y1(lsb) data[n+5] x2(msb) data...

  • Page 126

    3-67 3-67 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands - "solid shape" means blanked inside the shape. - "hole shape" means no blanking inside the shape. Projector type bd3100 v1.07/v2.07 , bd3100lc v1.07/v2.07 , bd5100 v1.07/v2.07 , b...

  • Page 127

    3-68 3-68 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands programmable blanking, write transmit start \xfe projector address \x01 command[0] \xe1 data[0] \x63 data[1] \x01 data[2] \x5e data[3] \x00 data[4] \xfa data[5] \x00 data[6] \xc8 d...

  • Page 128

    3-69 3-69 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the projector run time in seconds. Command command[0] \x62 data no data bytes. Return data the return data-transfer being the projector run time in seconds contain...

  • Page 129

    3-70 3-70 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands projector, read run time receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector addre...

  • Page 130

    3-71 3-71 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the serial number of the projector. Command command[0] \x61 data no data bytes. Return data the return data-transfer being the projector serial number is a pascal-...

  • Page 131

    3-72 3-72 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands projector, read serial number receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector ...

  • Page 132

    3-73 3-73 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description determine the type of projector you are communicating with. Command command[0] \x6b data no data bytes. Return data the return data-transfer being the projector type is...

  • Page 133

    3-74 3-74 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x6b d...

  • Page 134

    3-75 3-75 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands projector, write address projector, write address description write the projector address command command[0] \x6d data data[0] = projector address data[0] \x00..\xff projector type...

  • Page 135

    3-76 3-76 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the actual sharpness value. Command command[0] \x21 command[1] \x05 data no data bytes. Return data data[0] = sharpness value. Data[0] \x00..\x03 data[0] bd5000 bd...

  • Page 136

    3-77 3-77 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands example read the actual sharpness value of a projector with address \x01. Suppose the sharpness equals \x03. Transmit start \xfe projector address \x01 command[0] \x21 command[1] \...

  • Page 137

    3-78 3-78 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description write a new sharpness value. Command command[0] \x20 command[1] \x05 data data[0] = sharpness value. Data[0] \x00..\x03 data[0] bd5000 bd3000 bd2100 bd5000lc bd3000lc b...

  • Page 138

    3-79 3-79 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands example set the sharpness to \x03 on a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \x20 command[1] \x05 data[0] \x03 checksum \x29 stop \xff ...

  • Page 139

    3-80 3-80 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : close the mechanical shutter (optional). Command : command[0] \x23 command[1] \x42 data : data[0] = speed. Data[0] fast \x00 slow \x01 projector type : bd2100, bd2100...

  • Page 140

    3-81 3-81 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands example : close the shutter (full speed) of a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \x23 command[1] \x42 data[0] \x00 checksum \x66 sto...

  • Page 141

    3-82 3-82 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : open the mechanical shutter (optional). Command : command[0] \x22 command[1] \x42 data : data[0] = speed. Data[0] fast \x00 slow \x01 projector type : bd2100, bd2100l...

  • Page 142

    3-83 3-83 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands example : open the shutter (full speed) of a projector with address \x01. Transmit start \xfe projector address \x01 command[0] \x22 command[1] \x42 data[0] \x00 checksum \x65 stop...

  • Page 143

    3-84 3-84 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description : read the actual shutter position (optional). Command : command[0] \x21 command[1] \x42 data : no data bytes. Return data : data[0] = shutter position. Data[0] closed ...

  • Page 144

    3-85 3-85 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x21 c...

  • Page 145

    3-86 3-86 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands software, read language description read the language used in the on-screen-display. Command command[0] \x69 data no data bytes. Return data the return data-transfer being the soft...

  • Page 146

    3-87 3-87 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x69 d...

  • Page 147

    3-88 3-88 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the type of software installed in the projector. Command command[0] \x6a data no data bytes. Return data the return data-transfer being the software type is a pasc...

  • Page 148

    3-89 3-89 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x6a d...

  • Page 149

    3-90 3-90 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the version of the software. Command command[0] \x60 data no data bytes. Return data the return data-transfer being the software version is a pascal-language strin...

  • Page 150

    3-91 3-91 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x60 d...

  • Page 151

    3-92 3-92 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read slow/fast sync (only active when the decoder is used). Command command[0] \x21 command[1] \x27 data no data bytes. Return data data[0] = sync. Sync data[0] slow \x...

  • Page 152

    3-93 3-93 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x21 c...

  • Page 153

    3-94 3-94 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description set the sync to fast (only active when the decoder is used). Command command[0] \x27 command[1] \x27 data no data bytes. Projector type bd2100 v1.02 , bd2100lc v1.02 , ...

  • Page 154

    3-95 3-95 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description set the sync to slow (only active when the decoder is used). Command command[0] \x26 command[1] \x27 data no data bytes. Projector type bd2100 v1.02 , bd2100lc v1.02 , ...

  • Page 155

    3-96 3-96 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description set text off (identical to text button on infrared remote control). Command command[0] \x0e data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd3000lc, bd310...

  • Page 156

    3-97 3-97 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description set text on (identical to text button on infrared remote control). Command command[0] \x0d data no data bytes. Projector type bd2100, bd2100lc, bd3000, bd3000lc, bd3100...

  • Page 157

    3-98 3-98 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the actual treble value. Command command[0] \x21 command[1] \x09 data no data bytes. Return data data[0] = treble value. Data[0] \xfc..\x04 projector type bd2100, ...

  • Page 158

    3-99 3-99 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x21 c...

  • Page 159

    3-100 3-100 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands treble, write description write a new treble value. Command command[0] \x20 command[1] \x09 data data[0] = treble value. Data[0] \xfc..\x04 projector type bd2100, bd2100lc, bd300...

  • Page 160

    3-101 3-101 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description read the actual volume value. Command command[0] \x21 command[1] \x07 data no data bytes. Return data data[0] = volume value. Data[0] \x00..\x2c projector type bd2100...

  • Page 161

    3-102 3-102 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands receive (acknowledge) start \xfe projector address \x01 command[0] \x00 command[1] \x06 checksum \x07 stop \xff receive (answer) start \xfe projector address \x01 command[0] \x21...

  • Page 162

    3-103 3-103 user's manual r5975236-r3 user's manual r5975236-r3 chapter 3: advanced commands chapter 3: advanced commands description write a new volume value. Command command[0] \x20 command[1] \x07 data data[0] = volume value. Data[0] \x00..\x2c projector type bd2100, bd2100lc, bd3000, bd3000lc, b...

  • Page 163

    A-1 a-1 user's manual r5975236-r3 user's manual r5975236-r3 appendix a: command summary 2 appendix a: command summary 2 appendix a command summary 2 appendix a command summary 2.

  • Page 164

    A-2 a-2 user's manual r5975236-r3 user's manual r5975236-r3 appendix a: command summary 2 appendix a: command summary 2 appendix a appendix a balance, decrement : .................................. \x23\x0a balance, increment : .................................. \x22\x0a bass, decrement : .............

  • Page 165

    A-3 a-3 user's manual r5975236-r3 user's manual r5975236-r3 appendix a: command summary 2 appendix a: command summary 2 appendix a appendix a infrared control, color+ : .................................. \x30\x2c infrared control, color- : .................................. \x30\x2d infrared control...

  • Page 166

    A-4 a-4 user's manual r5975236-r3 user's manual r5975236-r3 appendix a: command summary 2 appendix a: command summary 2 appendix a appendix a sharpness, decrement : .................................. \x0a sharpness, increment : .................................. \x09 source/slot, read number : ........

  • Page 167

    B-1 b-1 user's manual r5975236-r3 user's manual r5975236-r3 appendix b: command summary 3 appendix b: command summary 3 appendix b command summary 3 appendix b command summary 3.

  • Page 168

    B-2 b-2 user's manual r5975236-r3 user's manual r5975236-r3 appendix b: command summary 3 appendix b: command summary 3 appendix b appendix a balance, read : ......... \x21\x0a balance, write : ......... \x20\x0a\xvv (\xvv = value) bass, read : ......... \x21\x08 bass, write : ......... \x20\x08\xvv...

  • Page 169

    B-3 b-3 user's manual r5975236-r3 user's manual r5975236-r3 appendix b: command summary 3 appendix b: command summary 3 appendix a appendix a lamp, read status : ......... \x6c lamp, reset run time : ......... \x68 lock audio, read : ......... \x21\x3f lock audio, write : ......... \x20\x3f phase, r...