30sg operator’s manual 11/25/13 page 1 of 24 the model 30sg hydraulic track stump grinder operator’s manual – original instructions stump grinder intended use the barreto stump grinder is designed to remove in-ground tree stumps and exposed roots. It should not be used to cut any material other than...
30sg operator’s manual 11/25/13 page 2 of 24 lubrication requirements grease at the intervals indicated per the illustration of grease lubrication points. There is also a grease diagram decal on the machine..
30sg operator’s manual 11/25/13 page 3 of 24 safety messages general safety messages are listed in this safety messages section. Specific safety messages appear as appropriate in this manual where a potential hazard may occur if procedures or instructions are not followed correctly and completely. S...
30sg operator’s manual 11/25/13 page 4 of 24 safety instructions overview read safety and operating instructions before operating! Use common sense and plenty of it! Call before you cut.If you do not call, you may cause an accident; suffer injuries or death; cause interruption of services; damage th...
30sg operator’s manual 11/25/13 page 5 of 24 safety instructions overview (continued) warning: contact with the cutter wheel while in operation will cause serious injury or even death. The teeth of the cutter wheel are sharp. Avoid contact even when the wheel is not moving. Avoid inclines if at all ...
30sg operator’s manual 11/25/13 page 6 of 24 safety instructions overview (continued) avoid contact with hydraulic fluid. Warning: when machine is operating, hydraulic fluid is under extreme pressure and can get under skin and burn or poison. Warning: keep safety guards and shields in place while th...
30sg operator’s manual 11/25/13 page 7 of 24 stump grinder operating instructions read safety instructions before operating! Both the safety instructions and operating instructions are in this manual. Be sure that the engine oil and fuel, and the machine hydraulic fluid are all at proper levels befo...
30sg operator’s manual 11/25/13 page 8 of 24 controls (continued) 4. Cutter wheel control: to start the cutter wheel, hold down the thumb button on the control handle. Then pull the trigger back. After the wheel is started, the thumb button can be released, but the trigger must be held to keep the c...
30sg operator’s manual 11/25/13 page 9 of 24 engine controls fuel shutoff valve: must be in open position for engine to run. Choke: use to aid starting the vanguard engine only when it is cold. Keyed ignition switch: this remote switch is located with the engine controls for your convenience. Use it...
30sg operator’s manual 11/25/13 page 10 of 24 engine start up procedure only operate machine outdoors and avoid breathing engine exhaust and fumes. Warning: engine exhaust contains carbon monoxide gas that is toxic. Breathing it can cause unconsciousness and death. Avoid any areas or actions that ex...
30sg operator’s manual 11/25/13 page 11 of 24 kohler start up procedure 1. Check the oil level. Add oil if low. Do not overfill. 2. Check the fuel level. Add fuel if low. Check the fuel system components and lines for leaks. 3. Check and clean the cooling areas, air intake areas and external surface...
30sg operator’s manual 11/25/13 page 12 of 24 briggs/vanguard controls & start up procedure starting the engine note: some engines and equipment have remote controls. See the equipment manual for location and operation of remote controls. 1. Check the oil level. See the how to check/add oil section ...
30sg operator’s manual 11/25/13 page 13 of 24 operator preparation each operator must: • become familiar with the controls and operation of the stump grinder, preferably under the supervision of an experienced operator. • be at least 18 yrs. Of age and be mentally and physically capable of operating...
30sg operator’s manual 11/25/13 page 14 of 24 vibration emission data declared vibration emission value in accordance with en 12096: the average measured vibration emission value is 2.0 m/s². The uncertainty in the measurement is 2.4 m/s². Safety gloves help to isolate the hands from the vibration, ...
30sg operator’s manual 11/25/13 page 15 of 24 determine location of underground utilities osha cfr 29 1926.651 requires that the estimated location of underground utilities be determined before beginning excavation or an underground drilling operation. When the actual excavation or bore approaches a...
30sg operator’s manual 11/25/13 page 16 of 24 work site assessment examine the work area for any conditions or obstructions that may inhibit cutting or create a safety hazard for the operator or others. Use the information in this manual combined with good judgment to identify any hazards to avoid. ...
30sg operator’s manual 11/25/13 page 17 of 24 contact with underground utilities after locating underground utilities and performing the work site assessment, accidental contact with a buried utility might still occur. If it does, stop and call 911 for help. If you cut a wire or cable, assume that y...
30sg operator’s manual 11/25/13 page 18 of 24 stump grinding procedure 1. Raise the cutter head and move the machine into position to cut. Position the machine so the cut head can swing across near the edge of the stump. 2. Have engine at full throttle (lever forward). 3. Start cutter wheel. 4. Usin...
30sg operator’s manual 11/25/13 page 19 of 24 jump starting engine with electric starter shield entire face, especially your eyes, and wear rubber gloves to avoid acid burns whenever doing anything with the battery. Battery caps must be tightly in place if the battery has removable caps. Warning: th...
30sg operator’s manual 11/25/13 page 20 of 24 ground transport of the stump grinder raise the cutter head. Warning: contact with the cutter wheel while in operation will cause serious injury or even death. The teeth of the cutter are sharp. Avoid contact even when the cutter is not moving. Track con...
30sg operator’s manual 11/25/13 page 21 of 24 emergency towing in case of engine failure there is a provision that allows the machine to be towed a short distance. The drive tracks are driven by a set of tandem pumps. The front pump drives right track, and the other pump drives left track. The drive...
30sg operator’s manual 11/25/13 page 22 of 24 road transport of the stump grinder the best way to transport the stump grinder over roads is with the barreto e4x6 tilt bed trailer. Refer to the following checklist before towing: • towing vehicle should have a 2" (5cm) ball. Be sure it is in good repa...
30sg operator’s manual 11/25/13 page 23 of 24 road transport of the stump grinder (continued) warning: navigating on the inclined trailer bed increases the danger of the tracks losing traction, especially if the bed surface is wet. If you lose control, get out of the way to avoid personal injury. Mo...
30sg operator’s manual 11/25/13 page 24 of 24 index battery, 1, 6, 19 choke, 9, 10 cold weather operations, 10 contact with underground utilities, 17 controls, 1, 7, 8, 12 emergency towing, 1, 21 engine, 3, 4, 5, 6, 7, 9, 10, 11, 12, 16, 17, 18, 19, 21, 22, 23 engine controls, 1, 9 fuel shutoff valv...
