Barska AX12658 User Manual

User’s Manual for Key Safe

WARNING

Read all instructions before using this safe.

A.  Handle

B.  Key Access

C.  Key Pad

D.  Indicator Lights

E.  Key Drop Slot

     - Located on the side of the safe

- For security purposes, change the factory default 

  code as soon as possible. Factory default code

  is 

159 and 011223.

-Test registered pin code a few times before closing

  the safe door.

- Avoid leaving door open and unattended; it will allow

  unauthorized individuals to reprogram the safe, 

  gaining full access to the safe and its contents.

- Store emergency keys in a secure place; NOT inside 

  of the safe.

- To maximize security and performance of the safe,

   test pin code every 6 months.

Lock

Unlock

See reverse side for more information

GETTING STARTED

Remove emergency keys and other included 

accessories from packaging.

KEY ACCESS

1. Remove grey key cover located on the safe to expose 

    key hole.

2. Use emergency key and insert into key hole, turn key 

    counter clockwise and turn handle clockwise.

BATTERY

Battery compartment is located on the inside of the door 

safe.

1. Remove battery compartment cover. 

2. Insert four AA alkaline batteries into the battery 

    compartment and restore battery compartment cover.

Note: Do not mix new and old batteries

PIN CODE REGISTRATION

    1st Safe Default Pin Code : 159

    2nd Safe Default Pin Code : 011223

1. Press “* *”, then yellow indicator light next to warning 

    will light up. 

2. Input current user code that you want to change, and 

    press “#”.

3. Input your new pin code you want to change it to and 

    press “#”. 

4. Input your new pin code one more time to confirm 

    registration and press “#.” Yellow light will turn off, 

    meaning code has been registered.

Repeat steps above to change second pin code

TESTING REGISTERED PIN CODE 

With safe door open turn handle counter clockwise to 

extend the bolts. Enter registered pin code and press “#” 

safe should unlock. Turn handle clockwise and bolts 

shall retract; if safe unlocked then registration is 

complete.

Note: If safe does not unlock then pin code registration 

was unsuccessful. Please start over with Pin Code 

Registration. 

DELETING PIN CODES / RESETTING SAFE TO 

FACTORY DEFAULT MODE

Please only reset the safe if Pin Codes are lost or 

forgotten.

PARTS OF THE SAFE

A

B

E

C

D

1. Open safe and remove screws securing the back

cover to the safe. 

2. You will see a small button located on the

    circuit board.

3. Press and hold small button until you see all the 

    lights flash and 2 quick beeps will be heard. 

4. All pin codes have been resetted to factory

   Default Pin Codes. 

Note: 1st Safe Default Pin Code : 159

         2nd Safe Default Pin Code : 011223

MOUNTING INSTRUCTIONS

The safe may be mounted to a wall. Be aware of the 

load bearing. Failure to do so can result in personal

injury and/or damage to property. Use appropriate 

tools when performing work and always use eye 

protection.

- Do not mount the safe without anchoring to the 

  wall.

- Find the studs in the wall, at your desired location. 

  Most studs are 16 inches or 24 inches apart.

- Check the wall for concealed wires or pipes.

- Measure the location of the pre-set drill holes; mark 

  their exact position onto the wall ensuring that the

  studs or anything else behind will not interfere.

- Drill the appropriate size holes for the anchors you

  are using.

- Carefully press the anchor into the holes at

  this time.

- Mount the safe by running screws from inside of the 

  safe and securing to anchors; ensure the safe is

  mounted securely.

8/16

BC451

© 2016 BARSKA®

855 Towne Center Drive | Pomona, CA 91767

(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com