Barska Biometric Safe User Manual

E. To Delete All Fingerprints / Initialization

1. Open door by pressing the wake-up button, a beep is heard 

    and red LED of sensor flashes.

2. Put finger on the scanner, a beep is heard and green LED of 

    sensor flashes once, then the door is opened automatically.

3. Unscrew battery cover and remove one battery.

4. Press wake-up button a few times to release remaining 

    electronic power.

5. Remove tamper resistant cover from initialization button.

    Press and hold initialization button on the inside of the door as 

    the battery is reinserted, you will hear 1 beep followed by 2 

    consecutive beeps, release initializing button the LED light will 

    flash green accordingly with the beeps. This may take a few 

    seconds. Replace tamper resistant cover back onto 

    initialization button. 

    Initialization deletes all fingerprints stored in the module. Now 

    any fingerprint can open the safe.

A. Parts of the Safe

F. Replacing Batteries

1. With the door open unscrew battery cover and remove

    batteries.

2. Press wake-up button a few times to release remaining 

    electronic power.

3. Reinstall new batteries and replace battery cover.

B. Registering Fingerprint

1. During set up the door must be open and the locking bolts in 

    the retracted position. Remove tamper resistant cover from

    initialization button.

2. During registration process, keep the safe door open and 

    locking bolts in the retracted postion. 

3. Press and release initialization button on the inside of the 

    safe door. Immediately place finger on scanner, you will hear 

    1 beep followed by 2 consecutive beeps. Remove fingerprint 

    from scanner. 

4. Registration of fingerprint is now complete. Replace tamper

    resistant cover back onto initialization button.

5. To add a fingerprint repeat steps 2 through 4.

Note:

      If fingerprint is not registered successfully, two short beeps

      will be heard and red LED flashes, check the operation and 

      register again.

      If the green and red LED flash alternatively 10 times, this

indicates the fingerprint memory is full. 

DO NOT lose tamper resistant cover. 

C. Locking Door

     Close the door and turn the handle counter clockwise

Note: Be sure the door is closed completely

     Alarm: When 3 beeps are heard, change the batteries in 

the safe. 

D.

Opening the Door with Fingerprint

1. Press wake-up button, a beep is heard and red LED of sensor

    flashes.

2. Put finger on scanner, a beep is heard and green led of  

    sensor flashes once, now turn the handle clockwise

3. If verification failed, two short beeps will be heard and red 

    LED flashes twice, then operate step 1 and 2 again.

Note: When no user fingerprint is registered, any finger can open 

the door

A. Initialization Button with 

    tamper resistant cover

B. Fingerprint Scanner

B

C

D

H. Opening the Safe with Key

Back up key access is located near the door handle of the safe

Entry access can either be a logo plate OR key cover. Key 

access is for emergency use. 

Safe Plate 

Use the screwdriver to twist the screws on the safe plate. Then 

open the door with the key. After opening door, take out the key 

and return the safe plate. 

Key Cover

Gently lift off the key cover and then open the door with the key. 

After opening door, take out the key and return the key cover 

back into place. 

A

User Manual for Biometric Safe

See reverse side for more information

G. External Battery Pack

Note: Included with select models 

         Use external battery pack only when batteries are low

1. Install batteries; note the polarity of the placement of batteries

2. Plug the external battery pack into the pink hole on the lower 

    left side of the fingerprint module

3. Press the wake-up button to open safe door by scanning a 

    fingerprint

I. Sound Options

To Turn Off Beep Sound

With the door open remove tamper resistant cover from 

initialization button. Press & hold initialization button until green 

light flashes, release initialization button. Replace tamper

resistant cover back onto initialization button. Beep is now 

disabled

To Turn On Beep Sound

With the door open remove tamper resistant cover from 

initialization button. Press & hold initialization button until green 

light flashes and you hear one beep. Replace tamper resistant 

cover back onto initialization button. Beep is now enabled

C. Wake-Up Button

D. Back Up Key Access

- or -