1. DL manuals
  2. Batca
  3. Fitness Equipment
  4. LD-2
  5. Owner's Manual

Batca LD-2 Owner's Manual

Summary of LD-2

  • Page 1

    Www.Batcafitness.Com ld-2 owner’s manual june 2011 revision 1 serial number here date of purchase owner’s manual mid row/lat pull down ld-2 1207 new hope road, raleigh, nc - 919.255.1233 - www.Batcafitness.Com.

  • Page 2

    Batca fitness systems 2 ld-2 owner's manual __________ page instructions 2 parts listing 3 hardware comparison 4-7 main assembly 8-18 upholstery 16 cable routing 15 congratulations on the purchase of your new batca ld-2. This gym will provide you with a lifetime of enjoyment to meet your strength tr...

  • Page 3

    Www.Batcafitness.Com 3 ld-2 owner’s manual frame components accessories upholstery hardware cables tools required 9/16” wrench 9/16” ratchet allen wrench set tape measure snap ring pliers item no. Part number description qty. 1 bfp-10842 ld-2 cage 1 2 bfp-10840 base assembly 1 3 bfp-10841 upright su...

  • Page 4

    Batca fitness systems 4 ld-2 owner's manual bolt length note: bolt length is measured from the underside of the head of the bolt..

  • Page 5

    Www.Batcafitness.Com 5 ld-2 owner’s manual.

  • Page 6

    Batca fitness systems 6 ld-2 owner's manual.

  • Page 7

    Www.Batcafitness.Com 7 ld-2 owner’s manual.

  • Page 8

    Batca fitness systems 8 ld-2 owner's manual step 1: note: for a more consistent appearance, position all bolts in the direction shown in each figure . Please follow all directions very carefully for proper installation. All flat washers and nylocks are 3/8” unless otherwise noted. Anywhere a washer ...

  • Page 9

    Www.Batcafitness.Com 9 ld-2 owner’s manual figure 2 step 2: item # part # description qty 3 bfp-10841 upright support 1 4 bfp-51768 curved anti-deflection plate 1 46 bfp-51756 shcs 3/8” x 5 1/4” 2 48 bfh-50204 3/8” curved washer 4 50 bfh-50157 3/8” nylock 2 do not tighten bolts until step 3 all flat...

  • Page 10

    Batca fitness systems 10 ld-2 owner's manual step 3: figure 3 all flat washers and nylocks are 3/8” unless otherwise noted. Anywhere a washer is against the round side of a tube there is to be a 3/8” curved washer instead of a 3/8” flat washer. Item # part # description qty 5 bfp-10843 mid row/lat p...

  • Page 11

    Www.Batcafitness.Com 11 ld-2 owner’s manual figure 4 step 4: all flat washers and nylocks are 3/8” unless otherwise noted. Item # part # description qty 13 bfp-10844 mid row arm 1 14 bfp-51784 axle 1 30 bfp-51696 small aluminum end cap 2 54 bfh-50620 bhscs 3/8” x 1” 2.

  • Page 12

    Batca fitness systems 12 ld-2 owner's manual step 5: all flat washers and nylocks are 3/8” unless otherwise noted. Item # part # description qty 15 bfp-10845 swivel pulley holder 1 16 bfp-10848 chrome seat adjustment tube 1 17 bfp-10847 chrome chest adjustment tube 1 31 bfh-50210 gas spring 1 32 bfh...

  • Page 13

    Www.Batcafitness.Com 13 ld-2 owner’s manual all flat washers and nylocks are 3/8” unless otherwise noted. Anywhere a washer is against the round side of a tube there is to be a 3/8” curved washer instead of a 3/8” flat washer. Step 6: item # part # description qty 18 bfp-10846 knee hold down assembl...

  • Page 14

    Batca fitness systems 14 ld-2 owner's manual step 7: figure 7 all flat washers and nylocks are 3/8” unless otherwise noted. Item # part # description qty 20 bfp-51797 placard plate 1 33 bfh-50174 4 1/2” pulley 1 37 bfp-52373 bhscs 3/8” x 3/4” 2 41 bfp-51752 shcs 3/8” x 2 1/4” 1 49 bfh-50146 3/8” fla...

  • Page 15

    Www.Batcafitness.Com 15 ld-2 owner’s manual all flat washers and nylocks are 3/8” unless otherwise noted. Step 8: item # part # description qty 24 cab-15003 mid row lockout to weight stack cable 1 33 bfh-50174 4 1/2” pulley 6 35 bfp-51746 1/2” pulley spacer 2 40 bfp-51759 shcs 3/8” x 2” 1 41 bfp-517...

  • Page 16

    Batca fitness systems 16 ld-2 owner's manual item # part # description qty 26 bfc-50125 single hook lat bar 1 27 bfp-52129 mid row chest pad 1 28 bfp-52130 large bottom pad 1 29 bfu-50189 7” upholstered roller 2 34 bfh-50622 large aluminum end cap 2 37 bfp-52373 bhscs 3/8” x 3/4” 2 39 bfp-51653 shcs...

  • Page 17

    Www.Batcafitness.Com 17 ld-2 owner’s manual all flat washers and nylocks are 3/8” unless otherwise noted. Step 10: figure 10 item # part # description qty 21 bfp-51740 rear weight stack shroud 1 37 bfp-52373 bhscs 3/8” x 3/4” 2 38 bfh-50254 hcs 3/8” x 3/4” 2 49 bfh-50146 3/8” flat washer 4 do not ti...

  • Page 18

    Batca fitness systems 18 ld-2 owner's manual item # part # description qty 22 bfp-51741 left front weight stack shroud 1 23 bfp-51742 right front weight stack shroud 1 step 11: figure 11 make sure all bolts are tightened.

  • Page 19

    Www.Batcafitness.Com 19 ld-2 owner’s manual final assembly and troubleshooting top plate 200lb stack weight stack decals: important - check these components before using gym: each cable with a threaded bolt on either end must be threaded at least 1/2” into its attachment, whether it be a free floate...

  • Page 20

    Batca fitness systems 20 ld-2 owner's manual  adjust cables to proper tension from any of the locations shown below. Note: all cables with threaded adjustable ends must have at least 1/2” of the threads threaded in to its counterpart. It is very important that the 1/2” jam nut be wrench tight- ened...

  • Page 21

    Www.Batcafitness.Com 21 ld-2 owner’s manual batca fitness systems strives to give you the very best in quality, performance and safety through carefully engineered designs and excellent workmanship. In order to maintain this high level of quality the preventative maintenance schedule below should be...

  • Page 22

    Batca fitness systems 22 ld-2 owner's manual what is covered for residential use: batca fitness systems warrants all of its products against defects in manufacturing, materials and workmanship under normal use and service for one year from date of purchase including paint, chrome, upholstery and gri...

  • Page 23

    Www.Batcafitness.Com 23 ld-2 owner’s manual the ld-2 has a layout dimension of 3’-8” (width) x 5’-1” (length) x 7’-0” (height). There should be a minimum of 18”, preferably 24”, of working space around the entire unit. Layout diagram.